Wave-making resistance

Wave-making resistance is a form of drag that affects surface watercraft, such as boats and ships, and reflects the energy required to push the water out of the way of the hull. This energy goes into creating the wave.

Physics

Graph of power versus speed for a displacement hull, with a mark at a speed–length ratio of 1.34

For small displacement hulls, such as sailboats or rowboats, wave-making resistance is the major source of the marine vessel drag.

A salient property of water waves is dispersiveness; i.e., the longer the wave, the faster it moves. Waves generated by a ship are affected by her geometry and speed, and most of the energy given by the ship for making waves is transferred to water through the bow and stern parts. Simply speaking, these two wave systems, i.e., bow and stern waves, interact with each other, and the resulting waves are responsible for the resistance.

The phase speed of deepwater waves is proportional to the square root of the wavelength of the generated waves, and the length of a ship causes the difference in phases of waves generated by bow and stern parts. Thus, there is a direct relationship between the waterline length (and thus wave propagation speed) and the magnitude of the wave-making resistance.

A simple way of considering wave-making resistance is to look at the hull in relation to bow and stern waves. If the length of a ship is half the length of the waves generated, the resulting wave will be very small due to cancellation, and if the length is the same as the wavelength, the wave will be large due to enhancement.

The phase speed $c$ of waves is given by the following formula:

$c={\sqrt {{\frac {g}{2\pi }}l}}$

where $l$ is the length of the wave and $g$ the gravitational acceleration. Substituting in the appropriate value for $g$ yields the equation:

${\mbox{c in knots}}\approx 1.341\times {\sqrt {{\mbox{length in ft}}}}\approx {\frac {4}{3}}\times {\sqrt {{\mbox{length in ft}}}}$

or, in metric units:

${\mbox{c in knots}}\approx 2.429\times {\sqrt {{\mbox{length in m}}}}\approx {\sqrt {6\times {\mbox{length in m}}}}\approx 2.5\times {\sqrt {{\mbox{length in m}}}}$

These values, 1.34, 2.5 and very easy 6, are often used in the hull speed rule of thumb used to compare potential speeds of displacement hulls, and this relationship is also fundamental to the Froude number, used in the comparison of different scales of watercraft.

When the vessel exceeds a "speed–length ratio" (speed in knots divided by square root of length in feet) of 0.94, it starts to outrun most of its bow wave, the hull actually settles slightly in the water as it is now only supported by two wave peaks. As the vessel exceeds a speed-length ratio of 1.34, the wavelength is now longer than the hull, and the stern is no longer supported by the wake, causing the stern to squat, and the bow to rise. The hull is now starting to climb its own bow wave, and resistance begins to increase at a very high rate. While it is possible to drive a displacement hull faster than a speed-length ratio of 1.34, it is prohibitively expensive to do so. Most large vessels operate at speed-length ratios well below that level, at speed-length ratios of under 1.0.

Ways of reducing wave-making resistance

Since wave-making resistance is based on the energy required to push the water out of the way of the hull, there are a number of ways that this can be minimized.

Reduced displacement

Reducing the displacement of the craft, by eliminating excess weight, is the most straightforward way to reduce the wave making drag. Another way is to shape the hull so as to generate lift as it moves through the water. Semi-displacement hulls and planing hulls do this, and they are able to break through the hull speed barrier and transition into a realm where drag increases at a much lower rate. The disadvantage of this is that planing is only practical on smaller vessels, with high power-to-weight ratios, such as motorboats. It is not a practical solution for a large vessel such as a supertanker.

Fine entry

A hull with a blunt bow has to push the water away very quickly to pass through, and this high acceleration requires large amounts of energy. By using a fine bow, with a sharper angle that pushes the water out of the way more gradually, the amount of energy required to displace the water will be less, even though the same total amount of water will be displaced. A modern variation is the wave-piercing design.

Bulbous bow

A special type of bow, called a bulbous bow, is often used on large power vessels to reduce wave-making drag. The bulb alters the waves generated by the hull, by changing the pressure distribution ahead of the bow. Because of the nature of its destructive interference with the bow wave, there is a limited range of vessel speeds over which it is effective. A bulbous bow must be properly designed to mitigate the wave-making resistance of a particular hull over a particular range of speeds. A bulb that works for one vessel's hull shape and one range of speeds could be detrimental to a different hull shape or a different speed range. Proper design and knowledge of a ship's intended operating speeds and conditions is therefore necessary when designing a bulbous bow.

Hull form filtering

If the hull is designed to operate at speeds substantially lower than hull speed then it is possible to refine the hull shape along its length to reduce wave resistance at one speed.This is only practical where the block coefficient of the hull is not a significant issue.

Semi-displacement and planing hulls

A graph showing resistance–weight ratio as a function of speed–length ratio for displacement, semi-displacement, and planing hulls

Since semi-displacement and planing hulls generate a significant amount of lift in operation, they are capable of breaking the barrier of the wave propagation speed and operating in realms of much lower drag, but to do this they must be capable of first pushing past that speed, which requires significant power. Once the hull gets over the hump of the bow wave, the rate of increase of the wave drag will start to reduce significantly.

A qualitative interpretation of the wave resistance plot is that a displacement hull resonates with a wave that has a crest near its bow and a trough near its stern, because the water is pushed away at the bow and pulled back at the stern. A planing hull simply pushed down on the water under it, so it resonates with a wave that has a trough under it, which has about twice the length and therefore four times the speed.

References

On the subject of high speed monohulls, Daniel Savitsky, Professor Emeritus, Davidson Laboratory, Stevens Institute of Technology

This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.