Wood veneer

Wood veneer RCA Dimensia console TV set

In woodworking, veneer refers to thin slices of wood, usually thinner than 3 mm (1/8 inch),[1] that typically are glued onto core panels (typically, wood, particle board or medium-density fiberboard) to produce flat panels such as doors, tops and panels for cabinets, parquet floors and parts of furniture. They are also used in marquetry. Plywood consists of three or more layers of veneer, each glued with its grain at right angles to adjacent layers for strength. Veneer beading is a thin layer of decorative edging placed around objects, such as jewelry boxes. Veneer is also used to replace decorative papers in Wood Veneer HPL. Veneer is also a type of manufactured board.

Veneer is obtained either by "peeling" the trunk of a tree or by slicing large rectangular blocks of wood known as flitches. The appearance of the grain and figure in wood comes from slicing through the growth rings of a tree and depends upon the angle at which the wood is sliced. There are three main types of veneer-making equipment used commercially:

Each slicing processes gives a very distinctive type of grain, depending upon the tree species. In any of the veneer-slicing methods, when the veneer is sliced, a distortion of the grain occurs. As it hits the wood, the knife blade creates a "loose" side where the cells have been opened up by the blade, and a "tight" side.

Historically veneers were also sawn, but this is more wasteful of wood. Veneering is an ancient art, dating back to at least the ancient Egyptians who used expensive and rare wood veneers over cheaper timbers to produce their furniture and sarcophagi.[2] During the Roman Empire, Romans also used veneered work in mass quantities.[3]

Producing wood veneers

The finest and rarest logs are sent to companies that produce veneer. The advantage to this practice is twofold. First, it provides the most financial gain to the owner of the log. Secondly, and of more importance to the woodworker, it greatly expands the amount of usable wood. While a log used for solid lumber is cut into thick pieces, usually no thinner than 1/8 of an inch (3 mm), veneers are cut as thin as 1/40 of an inch (0.6 mm). Depending on the cutting process used by the veneer manufacturer, very little wood is wasted by the saw blade thickness, known as the saw kerf. Accordingly, the yield of a rare grain pattern or wood type is greatly increased, in turn placing less stress on the resource. Some manufacturers even use a very wide knife to "slice off" the thin veneer pieces. In this way, none of the wood is wasted. The slices of veneer are always kept in the order in which they are cut from the log and are often sold this way.

Types of veneers

There are a few types of veneers available, each serving a particular purpose.

Advantages of using veneers

Compared to wood, one of the primary advantages of using veneer is stability. While solid wood can be prone to warping and splitting, because veneer is made of thin layers of wood glued together, the chances of splitting or cracking are reduced. Further, the glue used provides additional strength, making the end result stronger than natural wood.

Some projects built using wood veneer would not be possible to construct using solid lumber, owing to expansion and contraction caused by fluctuation of temperature and humidity. Another advantage of veneer is sustainability—furniture made with wood veneer uses less wood than the same piece of furniture made with solid wood. Further, veneer may also be more readily available than solid wood as exotic hardwood lumber can be scarce and very expensive.

Ecological characteristics

Buying veneers

Wood veneers are typically sold by the square foot. With the ability to join veneers, even small pieces are usable, resulting in very little waste. Many sources sell small packets of veneers that are sequence matched and are ideal for small projects. These make experimenting and practicing much more economical. It is also possible to buy plywood and other substrates with veneered faces for larger projects consisting of casework.

See also

References

  1. ↑ DK Publishing (2010). Woodwork: A Step-by-Step Photographic Guide to Successful Woodworking. Penguin. p. 198.
  2. ↑ "What is a wood veneer?". www.wonkeedonkeexljoinery.co.uk. Retrieved 2016-06-21.
  3. ↑ MacDonald, Nancy (2013). Woodworking (2nd ed.). Cengage Learning. pp. 782–784. ISBN 978-1-285-70050-2. Retrieved 12 November 2015.
  4. ↑ "Glossary of Wood Veneer Terms". oakwoodveneer.com.
This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.