Teddington Lock

Teddington Lock

Teddington Lock undergoing maintenance. From left to right – rollers, skiff lock, launch lock and barge lock
Waterway River Thames
Country England
County Greater London
Maintained by Environment Agency
Operation
  • Launch: Hydraulic
  • Skiff: Manual
  • Barge: Hydraulic
First built
  • Launch: 1811
  • Skiff: 1858
  • Barge: 1904
Length
  • Launch: 54.22 m (177 ft 11 in)
  • Skiff: 15.08 m (49 ft 6 in)
  • Barge: 198.12 m (650 ft 0 in)

[1]

Width
  • Launch: 7.41 m (24 ft 4 in)
  • Skiff: 1.77 m (5 ft 10 in)
  • Barge: 7.54 m (24 ft 9 in)

[1]

Fall 2.68 m (8 ft 10 in) [1]
Above sea level 14 ft (4.3 m)
Location of Teddington Lock in Greater London
Coordinates 51°25′54″N 0°19′26″W / 51.43167°N 0.32389°W / 51.43167; -0.32389Coordinates: 51°25′54″N 0°19′26″W / 51.43167°N 0.32389°W / 51.43167; -0.32389 [2]
Teddington is normally manned 24 hours
Teddington Lock
Molesey Weir
Molesey Lock
Middlegreen Road
A309 Hampton Court Bridge
River Mole
River Ember
Thames Ditton Island
Ditton marina
Raven's Ait
Hogsmill River
A308 Kingston Bridge
Kingston Railway Bridge
Steven's Eyot
Teddington Weir
foot bridges
moorings
rollers
Skiff Lock
Launch Lock
Barge Lock
River Thames
Barrage at Teddington Lock

Teddington Lock is a complex of three locks and a weir on the River Thames in England at Ham in south west London. The lock is on the southern side of the river.

The river downstream of the lock, known as the Tideway, is tidal, though the Richmond Lock barrage downstream limits the fall of water to maintain navigability at low tide. The boundary point between the Port of London Authority, which is the navigation authority downstream, and the Environment Agency, which is the navigation authority upstream is marked by an obelisk on the Surrey bank a few hundred yards below the lock. Though Teddington marks the tidal limit, in periods of very high fluvial flow the tidal influence can be seen as far upstream as East Molesey, location of the second lock on the Thames.[3][4]

The Teddington lock complex consists of three locks, a conventional launch lock, a very large barge lock and a small skiff lock. The barge lock has an additional set of gates in the middle so it can operate in two sizes.

The large bow shaped weir stretches across to Teddington from an island upstream of the lock which also acts as the centre point for the two bridges making up Teddington Lock Footbridge.

History

First lock, 1810

The Navigation Act obtained in April 1771 by the Thames Navigation Commission did not allow them to build locks below Maidenhead Bridge,[5] but from 1802, several plans for locks in the First District of the Thames, stretching from Staines to Teddington, were drawn up. Stephen Leach took over the post of Clerk of Works for the First District in 1802, following the retirement of Charles Truss at the age of 82. Just before his retirement, Truss has proposed locks at Molesey and Teddington, each having a weir with long tumbling bays, similar to modern practice. John Rennie had suggested a series of long cuts in 1794, and Truss adopted the same idea. Rennie and William Jessop again proposed four long cuts in 1805, each about 1.5 miles (2.4 km) long, but the Navigation Committee were thwarted by strong opposition from landowners.[6]

Zacchary Allnutt, by then Surveyor for the Second and Third Districts, stretching from Staines to Mapledurham, suggested locks at Chertsey, Sunbury and Teddington in 1805. Rennie submitted new proposals in 1809, with nine locks between Staines and Twickenham. Two would be without weirs, while the other seven would require large weirs to be built in the river. Finally Leach drafted plans in 1810, which he suggested were "at once practicable and expedient, the least expensive, and the most likely to pass through Parliament without opposition and yet calculated to remedy the most prominent evils complained of." An Act of Parliament was obtained by the City of London Corporation in June 1810, which authorised construction of locks and weirs at Chertsey, Shepperton, Sunbury and Teddington. Each would be 150 by 20 feet (45.7 by 6.1 m) with the associated weir having ample capacity for flood conditions. Rennie, Leach and the Navigation Committee visited the sites in July, to finalise the positioning of the lock.[6] Leach then took charge of the work, which was undertaken by contractors Joseph Kimber and John Dows who also built Sunbury Lock.[7][8]

Work at Teddington started in September 1810, but there were delays caused by flooding in November and December, and Leach awarded the contractors an extra £500. The lock was finished and opened in June 1811, but the weir was incomplete. The cofferdam protecting the works would need to be removed as river levels rose in the winter, which would have delayed completion until the following July, and so again Leach stepped in, awarding advance payments to the contractors, which enabled them to finish on time.[9] The lock was further upstream than the present lock complex at the point where the footbridge now crosses. It comprised three pairs of gates as stipulated in the act.[8] Total cost for lock, cut, weir, ballast and ground was £22,035 10s.  7 1⁄2d. of which the land from Lord Dysart's estate cost £282 10s. 5d..[10] The lock was, at first, highly unpopular with the local fishermen and bargemen. After attempts to smash it, the lock keeper was granted permission to keep "a blunderbuss with bayonet attached thereto" to ward off attacks on the lock.[11]

Rebuild, 1857

By 1827 the timber lock needed considerable repair and in 1829 the weir was destroyed by an accumulation of ice. It is noted that in 1843 the lock-keeper prevented a steam vessel from coming through the lock. At that time steam vessels were limited to travel as far as Richmond. As originally built, the lock had timber sides up to normal head water level, and turf sides above that. The crest of the weir was 3.5 feet (1.1 m) above low water level at Teddington, but following the removal of the piers of old London Bridge in 1832, the drop increased to 4.5 feet (1.4 m) and increased further to 6 feet (1.8 m) when dredging of the river was carried out.[9] The lower water levels at the bottom sill resulted in the occasional grounding of barges.

Consideration was given to removing the lock altogether in 1840.[12] However, it was decided to rebuild the lock and in June 1854 proposals included providing capacity for seagoing craft with a side lock for pleasure traffic. In June 1857 the first stone of the new lock was laid at the present position, being the central of the three locks, and it opened in 1858 together with the narrow skiff lock, (known as "the coffin"). The boat slide was added in 1869 and in the 1870s it is recorded that the weir collapsed twice causing enormous damage. After the weir had been rebuilt in 1871, the sluice bays were around 240 feet (73 m) wide, similar to the total width of the tumbling bays.[9]

Footbridges and Barge Lock

The footbridges were opened in 1889 and finally the barge lock, the largest lock on the river, was built in 1904–1905.[13] 7,000 cubic yards (5,400 m3) of the extracted gravel was used to raise the level of Cross Deep Ait, a former ait adjacent to Swan Island downstream, to protect it from flooding.[14] The footbridges are Grade II listed.[15]

World War II

In 1940 Teddington Lock was the assembly point for an enormous flotilla of small ships from the length of the River Thames to be used in the Evacuation of Dunkirk.

Recent developments

Early twenty-first century renovation and improvement work in the area around the locks was undertaken as part of the Thames Landscape Strategy Teddington Gateway project.[16][17]

In 2009 a local community group initiated a feasibility study for exploiting Teddington's weir for electricity generation, inspired by similar community-led generation schemes; Torrs Hydro and Settle Hydro. The study was encouraging and the Ham Hydro project now proposes using three reverse-Archimedean screws with a total output of 492 kilowatts (660 hp).[18] Environmental concerns, notably those raised by anglers about the potential effect on fish populations, prompted further environmental surveys during 2012. The outcome of these considerations is awaited before the London Borough of Richmond upon Thames will determine whether planning permission is to be granted for the scheme.[19][20]

Access to and across the lock

The lock is situated on the towpath on the Surrey side in Ham about a mile below Kingston-upon-Thames. It can normally only be reached on foot. The nearest road is Riverside Drive in Ham. Alternatively the lock can be reached from Ferry Road Teddington over the footbridges which cross the river there.

Reach above the lock

Kingston from the river

Located 0.5 miles (0.80 km) above the lock is Trowlock Island, towards the Teddington bank, followed by Steven's Eyot in the centre of the river. There are then Kingston Railway and Kingston Bridges. After 1 mile (1.6 km) the river then curves sharply to the right with Thames Ditton Island towards the village of the same name. Finally before Molesey Lock is Hampton Court Bridge.

Despite settlements on both sides of the lock having formed part of London since the 1960s, the banks are still often referred to as the "Middlesex" and "Surrey" banks.

On the Middlesex (Teddington etc.) side of the river going upstream, the bank generally consists of homes and gardens/communal grounds up to and inclusive of Hampton Wick at Kingston Bridge; Teddington Studios, Lensbury Club, watersports clubs/a football club and the nature reserve at Trowlock are on the stretch. Above Kingston Bridge is Hampton Court Park, which stretches as far as Hampton Court Bridge. Half the Longford River, which feeds the water-features of Hampton Court Palace, runs out of a grated culvert opposite Raven's Ait and below the Water Gallery. After Hampton Court Bridge (along the side of the weir stream) the bank adopts food/hotel use then residential use.

Scullers, skiffs and Thames Raters at Raven's Ait on one of the most active stretches of the river

On the Surrey side is a consistent green buffer and towpath between the river and Ham/Kingston, widening to Canbury Gardens, until the high-rise town centre is reached. The town's buildings switch to entertainment immediately south of Kingston Bridge. After the canalised mouth of the Hogsmill the riverside switches to a promenade with road by residential uses until Seething Wells reservoirs. Raven's Ait is upstream of the bridges in the centre of the river at Surbiton, followed by a marina. Long and Thames Dittons's riverside homes and pubs follow until beyond Thames Ditton Island. A riverside park and playing fields flank the mouth of the Mole until Hampton Court Bridge, near to the top of the reach, overlooking part of the Palace. Hampton Court railway station is before the bridge and just above it is Molesey Lock.

Boats

There are navigation transit markers between Kingston Bridge and Raven's Ait on the Hampton Court bank, to allow river users to check their speed. A powered boat may not pass except in emergencies between the markers in less than one minute. The reach is home to at least five sailing clubs, five rowing clubs, two skiffing and punting clubs, the Royal Canoe Club and two Sea Cadet centres. Numerous pleasure boats ply for trade, London Riverboat services and chartered trips between Kingston and Hampton Court.

Thames Path

The Thames Path as its towpath follows the Surrey side to Kingston Bridge where it crosses to run alongside Hampton Court Park, before returning to what is traditionally (and in navigation use) termed 'the Surrey side' at Hampton Court Bridge.

Sinuosity

The river makes an acute inside angle on this reach — the two locks are less than half the distance apart by land.

Sports clubs on the reach

The skiff lock at Teddington

The lock was the location of the Monty Python Fish-Slapping Dance sketch.

In episode 1 of series 5 of New Tricks (BBC TV police drama), the villain is arrested at Teddington Lock.

Thames Television had purpose-built studios at Teddington Lock.

See also

References

  1. 1 2 3 "A User's Guide to the River Thames" (PDF). PDF file. Environmental Agency. 2009. pp. 29–30. Retrieved 11 November 2012.
  2. ↑ "Teddington Lock website". Retrieved 3 March 2017.
  3. ↑ de Castella, Tom (11 February 2014). "How does the Thames Barrier stop London flooding?". BBC News Magazine.
  4. ↑ "Operation of the Thames Barrier". Spelthorne Borough Council. Retrieved 7 February 2015.
  5. ↑ Skempton 1996, p. 153.
  6. 1 2 Skempton 1996, p. 165.
  7. ↑ Skempton, Alec W., ed. (2002). A Biographical Dictionary of Civil Engineers in Great Britain and Ireland. 1. London: Thomas Telford, on behalf of the Institution of Civil Engineers. pp. 14,397. ISBN 978-0-7277-2939-2. OCLC 223272473.
  8. 1 2 Thacker, Fred. S. (1914). The Thames Highway. Holborn, London: Fred S. Thacker. pp. 206–208. LCCN 15024238.
  9. 1 2 3 Skempton 1996, p. 166.
  10. ↑ "Journal of the House of Commons". 69. HMSO. 1813: 844. (Appendix)
  11. ↑ Croad, Stephen (2003). Liquid History: The Thames Through Time. Batsford. p. 27. ISBN 978-0-7134-8834-0.
  12. ↑ "Number II, The Mapledurham Scheme". The Civil Engineers and Architect's Journal. 13: 66. February 1840.
  13. ↑ Thacker, Fred. S. (1920). The Thames Highway: Volume II Locks and Weirs. republished 1968 David & Charles. ISBN 978-0-7153-4233-6.
  14. ↑ "Site Description". Friends of Radnor Gardens. Retrieved 9 June 2015.
  15. ↑ Historic England. "Teddington Lock Footbridges (1391392)". National Heritage List for England. Retrieved 30 June 2017.
  16. ↑ "Thames Landscape Strategy Teddington Gateway project". Archived from the original on 24 July 2008. Retrieved 14 November 2005.
  17. ↑ "Oldest timber lock gates on the Thames treated to a makeover". Environment Agency. 15 November 2012.
  18. ↑ "From Idea To Reality". Ham Hydro. Retrieved 30 June 2013.
  19. ↑ "Hydropower at Teddington Weir". Thames Anglers Conservancy. Retrieved 30 June 2013.
  20. ↑ Fleming, Christine (28 December 2011). "Teddington weir hydro-electric application submitted". Richmond Guardian.

Bibliography

  • Skempton, Alec (1996). Civil Engineers and Engineering in Britain, 1600–1830. Variorum. ISBN 978-0-86078-578-1. 
Next lock upstream River Thames Next lock downstream
Molesey Lock
7.74 km (4.81 mi) [1]		 Teddington Lock
Grid reference: TQ165716		 Richmond Lock
  1. ↑ "Environment Agency Distances between locks on the River Thames". web page. Environmental Agency. 19 November 2012. Retrieved 21 November 2012. Distances given in km
This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.