Surface tension

Surface tension is the elastic tendency of a fluid surface which makes it acquire the least surface area possible. Surface tension allows insects (e.g. water striders), usually denser than water, to float and stride on a water surface.

At liquid–air interfaces, surface tension results from the greater attraction of liquid molecules to each other (due to cohesion) than to the molecules in the air (due to adhesion). The net effect is an inward force at its surface that causes the liquid to behave as if its surface were covered with a stretched elastic membrane. Thus, the surface becomes under tension from the imbalanced forces, which is probably where the term "surface tension" came from.^[1] Because of the relatively high attraction of water molecules for each other through a web of hydrogen bonds, water has a higher surface tension (72.8 millinewtons per meter at 20 °C) compared to that of most other liquids. Surface tension is an important factor in the phenomenon of capillarity.

Surface tension has the dimension of force per unit length, or of energy per unit area. The two are equivalent, but when referring to energy per unit of area, it is common to use the term surface energy, which is a more general term in the sense that it applies also to solids.

In materials science, surface tension is used for either surface stress or surface free energy.

Causes

Diagram of the forces on molecules of a liquid

The cohesive forces among liquid molecules are responsible for the phenomenon of surface tension. In the bulk of the liquid, each molecule is pulled equally in every direction by neighboring liquid molecules, resulting in a net force of zero. The molecules at the surface do not have the same molecules on all sides of them and therefore are pulled inwards. This creates some internal pressure and forces liquid surfaces to contract to the minimal area.

Surface tension is responsible for the shape of liquid droplets. Although easily deformed, droplets of water tend to be pulled into a spherical shape by the imbalance in cohesive forces of the surface layer. In the absence of other forces, including gravity, drops of virtually all liquids would be approximately spherical. The spherical shape minimizes the necessary "wall tension" of the surface layer according to Laplace's law.

Water droplet lying on a damask. Surface tension is high enough to prevent floating below the textile

Another way to view surface tension is in terms of energy. A molecule in contact with a neighbor is in a lower state of energy than if it were alone (not in contact with a neighbor). The interior molecules have as many neighbors as they can possibly have, but the boundary molecules are missing neighbors (compared to interior molecules) and therefore have a higher energy. For the liquid to minimize its energy state, the number of higher energy boundary molecules must be minimized. The minimized number of boundary molecules results in a minimal surface area.^[2] As a result of surface area minimization, a surface will assume the smoothest shape it can (mathematical proof that "smooth" shapes minimize surface area relies on use of the Euler–Lagrange equation). Since any curvature in the surface shape results in greater area, a higher energy will also result. Consequently, the surface will push back against any curvature in much the same way as a ball pushed uphill will push back to minimize its gravitational potential energy.

Effects of surface tension

Water

Several effects of surface tension can be seen with ordinary water:

Beading of rain water on a waxy surface, such as a leaf. Water adheres weakly to wax and strongly to itself, so water clusters into drops. Surface tension gives them their near-spherical shape, because a sphere has the smallest possible surface area to volume ratio.
Formation of drops occurs when a mass of liquid is stretched. The animation shows water adhering to the faucet gaining mass until it is stretched to a point where the surface tension can no longer keep the drop linked to the faucet. It then separates and surface tension forms the drop into a sphere. If a stream of water was running from the faucet, the stream would break up into drops during its fall. Gravity stretches the stream, then surface tension pinches it into spheres.^[3]
Flotation of objects denser than water occurs when the object is nonwettable and its weight is small enough to be borne by the forces arising from surface tension.^[2] For example, water striders use surface tension to walk on the surface of a pond in the following way. The nonwettability of the water strider's leg means there is no attraction between molecules of the leg and molecules of the water, so when the leg pushes down on the water, the surface tension of the water only tries to recover its flatness from its deformation due to the leg. This behavior of the water pushes the water strider upward so it can stand on the surface of the water as long as its mass is small enough that the water can support it. The surface of the water behaves like an elastic film: the insect's feet cause indentations in the water's surface, increasing its surface area^[4] and tendency of minimization of surface curvature (so area) of the water pushes the insect's feet upward.
Separation of oil and water (in this case, water and liquid wax) is caused by a tension in the surface between dissimilar liquids. This type of surface tension is called "interface tension", but its chemistry is the same.
Tears of wine is the formation of drops and rivulets on the side of a glass containing an alcoholic beverage. Its cause is a complex interaction between the differing surface tensions of water and ethanol; it is induced by a combination of surface tension modification of water by ethanol together with ethanol evaporating faster than water.

A. Water beading on a leaf
B. Water dripping from a tap
C. Water striders stay atop the liquid because of surface tension
D. Lava lamp with interaction between dissimilar liquids: water and liquid wax
E. Photo showing the "tears of wine" phenomenon.

Surfactants

Surface tension is visible in other common phenomena, especially when surfactants are used to decrease it:

Soap bubbles have very large surface areas with very little mass. Bubbles in pure water are unstable. The addition of surfactants, however, can have a stabilizing effect on the bubbles (see Marangoni effect). Note that surfactants actually reduce the surface tension of water by a factor of three or more.
Emulsions are a type of colloid in which surface tension plays a role. Tiny fragments of oil suspended in pure water will spontaneously assemble themselves into much larger masses. But the presence of a surfactant provides a decrease in surface tension, which permits stability of minute droplets of oil in the bulk of water (or vice versa).

Physics

Physical units

Surface tension, usually represented by the symbol γ, is measured in force per unit length. Its SI unit is newton per meter but the cgs unit of dyne per centimeter is also used.^[5]

\gamma =1~{\mathrm {{\frac {dyn}{cm}}}}=1~{\mathrm {{\frac {erg}{cm^{2}}}}}=1~{\mathrm {{\frac {mN}{m}}}}=0.001~{\mathrm {{\frac {N}{m}}}}=0.001~{\mathrm {{\frac {J}{m^{2}}}}}

Surface area growth

This diagram illustrates the force necessary to increase the surface area. This force is proportional to the surface tension.

Surface tension can be defined in terms of force or energy.

In terms of force: surface tension $γ$ of a liquid is the force per unit length. In the illustration on the right, the rectangular frame, composed of three unmovable sides (black) that form a "U" shape, and a fourth movable side (blue) that can slide to the right. Surface tension will pull the blue bar to the left; the force $F$ required to hold the immobile side is proportional to the length $L$ of the movable side. Thus the ratio $F / L$ depends only on the intrinsic properties of the liquid (composition, temperature, etc.), not on its geometry. For example, if the frame had a more complicated shape, the ratio $F / L$ , with $L$ the length of the movable side and $F$ the force required to stop it from sliding, is found to be the same for all shapes. We therefore define the surface tension as

\gamma ={\frac {1}{2}}{\frac {F}{L}}.

The reason for the 1/2 is that the film has two sides, each of which contributes equally to the force; so the force contributed by a single side is $γL = F / 2$ .

In terms of energy: surface tension $γ$ of a liquid is the ratio of the change in the energy of the liquid, and the change in the surface area of the liquid (that led to the change in energy). This can be easily related to the previous definition in terms of force:^[6] if $F$ is the force required to stop the side from starting to slide, then this is also the force that would keep the side in the state of sliding at a constant speed (by Newton's Second Law). But if the side is moving to the right (in the direction the force is applied), then the surface area of the stretched liquid is increasing while the applied force is doing work on the liquid. This means that increasing the surface area increases the energy of the film. The work done by the force $F$ in moving the side by distance $Δ x$ is $W = F Δ x$ ; at the same time the total area of the film increases by $Δ A = 2 L Δ x$ (the factor of 2 is here because the liquid has two sides, two surfaces). Thus, multiplying both the numerator and the denominator of $γ = 1 / 2 F / L$ by $Δ x$ , we get

\gamma=\frac{F}{2L}=\frac{F \Delta x}{2 L \Delta x}=\frac{W}{\Delta A}

This work $W$ is, by the usual arguments, interpreted as being stored as potential energy. Consequently, surface tension can be also measured in SI system as joules per square meter and in the cgs system as ergs per cm². Since mechanical systems try to find a state of minimum potential energy, a free droplet of liquid naturally assumes a spherical shape, which has the minimum surface area for a given volume. The equivalence of measurement of energy per unit area to force per unit length can be proven by dimensional analysis.^[7]

Surface curvature and pressure

Surface tension forces acting on a tiny (differential) patch of surface.

δθ x

and

δθ y

indicate the amount of bend over the dimensions of the patch. Balancing the tension forces with pressure leads to the Young–Laplace equation

If no force acts normal to a tensioned surface, the surface must remain flat. But if the pressure on one side of the surface differs from pressure on the other side, the pressure difference times surface area results in a normal force. In order for the surface tension forces to cancel the force due to pressure, the surface must be curved. The diagram shows how surface curvature of a tiny patch of surface leads to a net component of surface tension forces acting normal to the center of the patch. When all the forces are balanced, the resulting equation is known as the Young–Laplace equation:^[8]

\Delta p=\gamma \left({\frac {1}{R_{x}}}+{\frac {1}{R_{y}}}\right)

where:

$Δ p$ is the pressure difference, known as the Laplace pressure.^[9]
$γ$ is surface tension.
$R x$ and $R y$ are radii of curvature in each of the axes that are parallel to the surface.

The quantity in parentheses on the right hand side is in fact (twice) the mean curvature of the surface (depending on normalisation). Solutions to this equation determine the shape of water drops, puddles, menisci, soap bubbles, and all other shapes determined by surface tension (such as the shape of the impressions that a water strider's feet make on the surface of a pond). The table below shows how the internal pressure of a water droplet increases with decreasing radius. For not very small drops the effect is subtle, but the pressure difference becomes enormous when the drop sizes approach the molecular size. (In the limit of a single molecule the concept becomes meaningless.)

$Δ p$ for water drops of different radii at STP
Droplet radius	1 mm	0.1 mm	1 μm	10 nm
$Δ p$ (atm)	0.0014	0.0144	1.436	143.6

Floating objects

Cross-section of a needle floating on the surface of water.

F w

is the weight and

F s

are surface tension resultant forces.

When an object is placed on a liquid, its weight $F w$ depresses the surface, and if surface tension and downward force becomes equal than is balanced by the surface tension forces on either side $F s$ , which are each parallel to the water's surface at the points where it contacts the object. Notice that small moment in the body may cause the object sink as the angle of contact decreases surface tension decreases the horizontal components of the two $F s$ arrows point in opposite directions, so they cancel each other, but the vertical components point in the same direction and therefore add up^[2] to balance $F w$ . The object's surface must not be wettable for this to happen, and its weight must be low enough for the surface tension to support it.

F_{\mathrm {w} }=2F_{\mathrm {s} }\cos \theta \quad \Leftrightarrow \quad \rho _{\mathrm {w} }A_{\mathrm {w} }Lg=2\gamma L\cos \theta

Liquid surface

Minimal surface

To find the shape of the minimal surface bounded by some arbitrary shaped frame using strictly mathematical means can be a daunting task. Yet by fashioning the frame out of wire and dipping it in soap-solution, a locally minimal surface will appear in the resulting soap-film within seconds.^[7]^[10]

The reason for this is that the pressure difference across a fluid interface is proportional to the mean curvature, as seen in the Young–Laplace equation. For an open soap film, the pressure difference is zero, hence the mean curvature is zero, and minimal surfaces have the property of zero mean curvature.

Contact angles

The surface of any liquid is an interface between that liquid and some other medium.^{[note 1]} The top surface of a pond, for example, is an interface between the pond water and the air. Surface tension, then, is not a property of the liquid alone, but a property of the liquid's interface with another medium. If a liquid is in a container, then besides the liquid/air interface at its top surface, there is also an interface between the liquid and the walls of the container. The surface tension between the liquid and air is usually different (greater than) its surface tension with the walls of a container. And where the two surfaces meet, their geometry must be such that all forces balance.^[7]^[8]

Forces at contact point shown for contact angle greater than 90° (left) and less than 90° (right)

Where the two surfaces meet, they form a contact angle, $θ$ , which is the angle the tangent to the surface makes with the solid surface. Note that the angle is measured through the liquid, as shown in the diagrams above. The diagram to the right shows two examples. Tension forces are shown for the liquid–air interface, the liquid–solid interface, and the solid–air interface. The example on the left is where the difference between the liquid–solid and solid–air surface tension, $γ ls - γ sa$ , is less than the liquid–air surface tension, $γ la$ , but is nevertheless positive, that is

\gamma _{\mathrm {la} }>\gamma _{\mathrm {ls} }-\gamma _{\mathrm {sa} }>0

In the diagram, both the vertical and horizontal forces must cancel exactly at the contact point, known as equilibrium. The horizontal component of $f la$ is canceled by the adhesive force, $f A$ .^[7]

f_{\mathrm {A} }=f_{\mathrm {la} }\sin \theta

The more telling balance of forces, though, is in the vertical direction. The vertical component of $f la$ must exactly cancel the force, $f ls$ .^[7]

f_{\mathrm {ls} }-f_{\mathrm {sa} }=-f_{\mathrm {la} }\cos \theta

Liquid

Solid

Contact angle

water

soda-lime glass

lead glass

0°

paraffin wax

107°

silver

90°

methyl iodide

soda-lime glass

29°

lead glass

30°

fused quartz

33°

mercury

soda-lime glass

140°

Some liquid–solid contact angles^[7]

Since the forces are in direct proportion to their respective surface tensions, we also have:^[8]

\gamma _{\mathrm {ls} }-\gamma _{\mathrm {sa} }=-\gamma _{\mathrm {la} }\cos \theta

where

$γ ls$ is the liquid–solid surface tension,
$γ la$ is the liquid–air surface tension,
$γ sa$ is the solid–air surface tension,
$θ$ is the contact angle, where a concave meniscus has contact angle less than 90° and a convex meniscus has contact angle of greater than 90°.^[7]

This means that although the difference between the liquid–solid and solid–air surface tension, $γ ls - γ sa$ , is difficult to measure directly, it can be inferred from the liquid–air surface tension, $γ la$ , and the equilibrium contact angle, $θ$ , which is a function of the easily measurable advancing and receding contact angles (see main article contact angle).

This same relationship exists in the diagram on the right. But in this case we see that because the contact angle is less than 90°, the liquid–solid/solid–air surface tension difference must be negative:

\gamma _{\mathrm {la} }>0>\gamma _{\mathrm {ls} }-\gamma _{\mathrm {sa} }

Special contact angles

Observe that in the special case of a water–silver interface where the contact angle is equal to 90°, the liquid–solid/solid–air surface tension difference is exactly zero.

Another special case is where the contact angle is exactly 180°. Water with specially prepared Teflon approaches this.^[8] Contact angle of 180° occurs when the liquid–solid surface tension is exactly equal to the liquid–air surface tension.

\gamma _{\mathrm {la} }=\gamma _{\mathrm {ls} }-\gamma _{\mathrm {sa} }>0\qquad \theta =180^{\circ }

Methods of measurement

Surface tension can be measured using the pendant drop method on a goniometer.

Because surface tension manifests itself in various effects, it offers a number of paths to its measurement. Which method is optimal depends upon the nature of the liquid being measured, the conditions under which its tension is to be measured, and the stability of its surface when it is deformed.

Du Noüy ring method: The traditional method used to measure surface or interfacial tension. Wetting properties of the surface or interface have little influence on this measuring technique. Maximum pull exerted on the ring by the surface is measured.^[11]
Du Noüy–Padday method: A minimized version of Du Noüy method uses a small diameter metal needle instead of a ring, in combination with a high sensitivity microbalance to record maximum pull. The advantage of this method is that very small sample volumes (down to few tens of microliters) can be measured with very high precision, without the need to correct for buoyancy (for a needle or rather, rod, with proper geometry). Further, the measurement can be performed very quickly, minimally in about 20 seconds. First commercial multichannel tensiometers [CMCeeker] were recently built based on this principle.
Wilhelmy plate method: A universal method especially suited to check surface tension over long time intervals. A vertical plate of known perimeter is attached to a balance, and the force due to wetting is measured.^[12]
Spinning drop method: This technique is ideal for measuring low interfacial tensions. The diameter of a drop within a heavy phase is measured while both are rotated.
Pendant drop method: Surface and interfacial tension can be measured by this technique, even at elevated temperatures and pressures. Geometry of a drop is analyzed optically. For pendant drops the maximum diameter and the ratio between this parameter and the diameter at the distance of the maximum diameter from the drop apex has been used to evaluate the size and shape parameters in order to determine surface tension.
Bubble pressure method (Jaeger's method): A measurement technique for determining surface tension at short surface ages. Maximum pressure of each bubble is measured.
Drop volume method: A method for determining interfacial tension as a function of interface age. Liquid of one density is pumped into a second liquid of a different density and time between drops produced is measured.^[13]
Capillary rise method: The end of a capillary is immersed into the solution. The height at which the solution reaches inside the capillary is related to the surface tension by the equation discussed below.^[14]
Stalagmometric method: A method of weighting and reading a drop of liquid.
Sessile drop method: A method for determining surface tension and density by placing a drop on a substrate and measuring the contact angle (see Sessile drop technique).^[15]
Vibrational frequency of levitated drops: The natural frequency of vibrational oscillations of magnetically levitated drops has been used to measure the surface tension of superfluid ⁴He. This value is estimated to be 0.375 dyn/cm at $T$ = 0 K.^[16]
Resonant oscillations of spherical and hemispherical liquid drop: The technique is based on measuring the resonant frequency of spherical and hemispherical pendant droplets driven in oscillations by a modulated electric field. The surface tension and viscosity can be evaluated from the obtained resonant curves.^[17]^[18]^[19]

Effects

Liquid in a vertical tube

Diagram of a mercury barometer

An old style mercury barometer consists of a vertical glass tube about 1 cm in diameter partially filled with mercury, and with a vacuum (called Torricelli's vacuum) in the unfilled volume (see diagram to the right). Notice that the mercury level at the center of the tube is higher than at the edges, making the upper surface of the mercury dome-shaped. The center of mass of the entire column of mercury would be slightly lower if the top surface of the mercury were flat over the entire cross-section of the tube. But the dome-shaped top gives slightly less surface area to the entire mass of mercury. Again the two effects combine to minimize the total potential energy. Such a surface shape is known as a convex meniscus.

We consider the surface area of the entire mass of mercury, including the part of the surface that is in contact with the glass, because mercury does not adhere to glass at all. So the surface tension of the mercury acts over its entire surface area, including where it is in contact with the glass. If instead of glass, the tube was made out of copper, the situation would be very different. Mercury aggressively adheres to copper. So in a copper tube, the level of mercury at the center of the tube will be lower than at the edges (that is, it would be a concave meniscus). In a situation where the liquid adheres to the walls of its container, we consider the part of the fluid's surface area that is in contact with the container to have negative surface tension. The fluid then works to maximize the contact surface area. So in this case increasing the area in contact with the container decreases rather than increases the potential energy. That decrease is enough to compensate for the increased potential energy associated with lifting the fluid near the walls of the container.

Illustration of capillary rise and fall. Red=contact angle less than 90°; blue=contact angle greater than 90°

If a tube is sufficiently narrow and the liquid adhesion to its walls is sufficiently strong, surface tension can draw liquid up the tube in a phenomenon known as capillary action. The height to which the column is lifted is given by:^[7]

h={\frac {2\gamma _{\mathrm {la} }\cos \theta }{\rho gr}}

where

$h$ is the height the liquid is lifted,
$γ la$ is the liquid–air surface tension,
$ρ$ is the density of the liquid,
$r$ is the radius of the capillary,
$g$ is the acceleration due to gravity,
$θ$ is the angle of contact described above. If $θ$ is greater than 90°, as with mercury in a glass container, the liquid will be depressed rather than lifted.

Puddles on a surface

Profile curve of the edge of a puddle where the contact angle is 180°. The curve is given by the formula:^[8]

x-x_{0}={\frac {1}{2}}H\cosh ^{-1}\left({\frac {H}{h}}\right)-H{\sqrt {1-{\frac {h^{2}}{H^{2}}}}}

where

H=2{\sqrt {\frac {\gamma }{g\rho }}}

Small puddles of water on a smooth clean surface have perceptible thickness.

Pouring mercury onto a horizontal flat sheet of glass results in a puddle that has a perceptible thickness. The puddle will spread out only to the point where it is a little under half a centimetre thick, and no thinner. Again this is due to the action of mercury's strong surface tension. The liquid mass flattens out because that brings as much of the mercury to as low a level as possible, but the surface tension, at the same time, is acting to reduce the total surface area. The result of the compromise is a puddle of a nearly fixed thickness.

The same surface tension demonstration can be done with water, lime water or even saline, but only on a surface made of a substance to which water does not adhere. Wax is such a substance. Water poured onto a smooth, flat, horizontal wax surface, say a waxed sheet of glass, will behave similarly to the mercury poured onto glass.

The thickness of a puddle of liquid on a surface whose contact angle is 180° is given by:^[8]

h=2{\sqrt {\frac {\gamma }{g\rho }}}

where

$h$ is the depth of the puddle in centimeters or meters.
$γ$ is the surface tension of the liquid in dynes per centimeter or newtons per meter.
$g$ is the acceleration due to gravity and is equal to 980 cm/s² or 9.8 m/s²
$ρ$ is the density of the liquid in grams per cubic centimeter or kilograms per cubic meter

Illustration of how lower contact angle leads to reduction of puddle depth

In reality, the thicknesses of the puddles will be slightly less than what is predicted by the above formula because very few surfaces have a contact angle of 180° with any liquid. When the contact angle is less than 180°, the thickness is given by:^[8]

h={\sqrt {\frac {2\gamma _{\mathrm {la} }\left(1-\cos \theta \right)}{g\rho }}}.

For mercury on glass, $γ Hg$ = 487 dyn/cm, $ρ Hg$ = 13.5 g/cm³ and $θ$ = 140°, which gives $h Hg$ = 0.36 cm. For water on paraffin at 25 °C, $γ$ = 72 dyn/cm, $ρ$ = 1.0 g/cm³, and $θ$ = 107° which gives $h H 2 O$ = 0.44 cm.

The formula also predicts that when the contact angle is 0°, the liquid will spread out into a micro-thin layer over the surface. Such a surface is said to be fully wettable by the liquid.

The breakup of streams into drops

Intermediate stage of a jet breaking into drops. Radii of curvature in the axial direction are shown. Equation for the radius of the stream is

R (z) = R 0 + A k cos (kz)

, where

R 0

is the radius of the unperturbed stream,

A k

is the amplitude of the perturbation,

z

is distance along the axis of the stream, and

k

is the wave number

In day-to-day life all of us observe that a stream of water emerging from a faucet will break up into droplets, no matter how smoothly the stream is emitted from the faucet. This is due to a phenomenon called the Plateau–Rayleigh instability,^[8] which is entirely a consequence of the effects of surface tension.

The explanation of this instability begins with the existence of tiny perturbations in the stream. These are always present, no matter how smooth the stream is. If the perturbations are resolved into sinusoidal components, we find that some components grow with time while others decay with time. Among those that grow with time, some grow at faster rates than others. Whether a component decays or grows, and how fast it grows is entirely a function of its wave number (a measure of how many peaks and troughs per centimeter) and the radii of the original cylindrical stream.

Thermodynamics

Thermodynamic theories of surface tension

J.W. Gibbs developed the thermodynamic theory of capillarity based on the idea of surfaces of discontinuity.^[20] He introduced and studied thermodynamics of two-dimensional objects – surfaces. These surfaces have area, mass, entropy, energy and free energy. As stated above, the mechanical work needed to increase a surface area A is $dW = γ dA$ . Hence at constant temperature and pressure, surface tension equals Gibbs free energy per surface area:^[8]

\gamma = \left( \frac{\partial G}{\partial A} \right)_{T,P,n}

where $G$ is Gibbs free energy and $A$ is the area.

Thermodynamics requires that all spontaneous changes of state are accompanied by a decrease in Gibbs free energy.

From this it is easy to understand why decreasing the surface area of a mass of liquid is always spontaneous ( $G < 0$ ), provided it is not coupled to any other energy changes. It follows that in order to increase surface area, a certain amount of energy must be added.

Gibbs free energy is defined by the equation^[21] $G = H - TS$ , where $H$ is enthalpy and $S$ is entropy. Based upon this and the fact that surface tension is Gibbs free energy per unit area, it is possible to obtain the following expression for entropy per unit area:

\left( \frac{\partial \gamma}{\partial T} \right)_{A,P}=-S^{A}

Kelvin's equation for surfaces arises by rearranging the previous equations. It states that surface enthalpy or surface energy (different from surface free energy) depends both on surface tension and its derivative with temperature at constant pressure by the relationship.^[22]

H^{A}=\gamma -T\left({\frac {\partial \gamma }{\partial T}}\right)_{P}

Fifteen years after Gibbs, J.D. van der Waals developed the theory of capillarity effects based on the hypothesis of a continuous variation of density.^[23] He added to the energy density the term $c(\nabla \rho )^{2},$ where c is the capillarity coefficient and ρ is the density. For the multiphase equilibria, the results of the van der Waals approach practically coincide with the Gibbs formulae, but for modelling of the dynamics of phase transitions the van der Waals approach is much more convenient.^[24]^[25] The van der Waals capillarity energy is now widely used in the phase field models of multiphase flows. Such terms are also discovered in the dynamics of non-equilibrium gases.^[26]

Thermodynamics of soap bubbles

The pressure inside an ideal (one surface) soap bubble can be derived from thermodynamic free energy considerations. At constant temperature and particle number, $dT = dN = 0$ , the differential Helmholtz energy is given by

dF=-P\,dV+\gamma \,dA

where $P$ is the difference in pressure inside and outside of the bubble, and $γ$ is the surface tension. In equilibrium, $dF = 0$ , and so,

P\,dV=\gamma \,dA

For a spherical bubble, the volume and surface area are given simply by

V={\tfrac {4}{3}}\pi R^{3}\quad \rightarrow \quad dV\approx 4\pi R^{2}\,dR,

and

A=4\pi R^{2}\quad \rightarrow \quad dA\approx 8\pi R\,dR.

Substituting these relations into the previous expression, we find

P={\frac {2}{R}}\gamma ,

which is equivalent to the Young–Laplace equation when $R x = R y$ . For real soap bubbles, the pressure is doubled due to the presence of two interfaces, one inside and one outside.

Influence of temperature

Temperature dependence of the surface tension between the liquid and vapor phases of pure water

Temperature dependency of the surface tension of benzene

Surface tension is dependent on temperature. For that reason, when a value is given for the surface tension of an interface, temperature must be explicitly stated. The general trend is that surface tension decreases with the increase of temperature, reaching a value of 0 at the critical temperature. For further details see Eötvös rule. There are only empirical equations to relate surface tension and temperature:

Eötvös:^[11]^[22]^[27]

\gamma V^{\frac {2}{3}}=k(T_{\mathrm {C} }-T).

Here $V$ is the molar volume of a substance, $T C$ is the critical temperature and $k$ is a constant valid for almost all substances.^[11] A typical value is $k$ = 6993210000000000000♠2.1×10⁻⁷ J K⁻¹ mol^{− ²⁄₃}.^[11]^[27] For water one can further use $V$ = 18 ml/mol and $T C$ = 647 K (374 °C).^[28]

A variant on Eötvös is described by Ramay and Shields:^[21]

\gamma V^{\frac {2}{3}}=k\left(T_{\mathrm {C} }-T-6\right)

where the temperature offset of 6 kelvins provides the formula with a better fit to reality at lower temperatures.

Guggenheim–Katayama:^[22]

\gamma =\gamma ^{\circ }\left(1-{\frac {T}{T_{\mathrm {C} }}}\right)^{n}

$γ °$ is a constant for each liquid and $n$ is an empirical factor, whose value is 11/9 for organic liquids. This equation was also proposed by van der Waals, who further proposed that $γ °$ could be given by the expression

K_{2}T_{\mathrm {C} }^{\frac {1}{3}}P_{\mathrm {C} }^{\frac {2}{3}},

where $K 2$ is a universal constant for all liquids, and $P C$ is the critical pressure of the liquid (although later experiments found $K 2$ to vary to some degree from one liquid to another).^[22]

Both Guggenheim–Katayama and Eötvös take into account the fact that surface tension reaches 0 at the critical temperature, whereas Ramay and Shields fails to match reality at this endpoint.

Influence of solute concentration

Solutes can have different effects on surface tension depending on the nature of the surface and the solute:

Little or no effect, for example sugar at water|air, most organic compounds at oil|air
Increase surface tension, most inorganic salts at water|air
Non-monotonic change, most inorganic acids at water|air
Decrease surface tension progressively, as with most amphiphiles, e.g., alcohols at water|air
Decrease surface tension until certain critical concentration, and no effect afterwards: surfactants that form micelles

What complicates the effect is that a solute can exist in a different concentration at the surface of a solvent than in its bulk. This difference varies from one solute–solvent combination to another.

Gibbs isotherm states that:

\Gamma =-{\frac {1}{RT}}\left({\frac {\partial \gamma }{\partial \ln C}}\right)_{T,P}

$Γ$ is known as surface concentration, it represents excess of solute per unit area of the surface over what would be present if the bulk concentration prevailed all the way to the surface. It has units of mol/m²
$C$ is the concentration of the substance in the bulk solution.
$R$ is the gas constant and $T$ the temperature

Certain assumptions are taken in its deduction, therefore Gibbs isotherm can only be applied to ideal (very dilute) solutions with two components.

Influence of particle size on vapor pressure

The Clausius–Clapeyron relation leads to another equation also attributed to Kelvin, as the Kelvin equation. It explains why, because of surface tension, the vapor pressure for small droplets of liquid in suspension is greater than standard vapor pressure of that same liquid when the interface is flat. That is to say that when a liquid is forming small droplets, the equilibrium concentration of its vapor in its surroundings is greater. This arises because the pressure inside the droplet is greater than outside.^[21]

P_{\mathrm {v} }^{\mathrm {fog} }=P_{\mathrm {v} }^{\circ }e^{\frac {V2\gamma }{RTr_{\mathrm {k} }}}

Molecules on the surface of a tiny droplet (left) have, on average, fewer neighbors than those on a flat surface (right). Hence they are bound more weakly to the droplet than are flat-surface molecules.

$P v °$ is the standard vapor pressure for that liquid at that temperature and pressure.
$V$ is the molar volume.
$R$ is the gas constant
$r k$ is the Kelvin radius, the radius of the droplets.

The effect explains supersaturation of vapors. In the absence of nucleation sites, tiny droplets must form before they can evolve into larger droplets. This requires a vapor pressure many times the vapor pressure at the phase transition point.^[21]

This equation is also used in catalyst chemistry to assess mesoporosity for solids.^[29]

The effect can be viewed in terms of the average number of molecular neighbors of surface molecules (see diagram).

The table shows some calculated values of this effect for water at different drop sizes:

$P / P 0$ for water drops of different radii at STP^[22]
Droplet radius (nm)	1000	100	10	1
$P / P 0$	1.001	1.011	1.114	2.95

The effect becomes clear for very small drop sizes, as a drop of 1 nm radius has about 100 molecules inside, which is a quantity small enough to require a quantum mechanics analysis.

Surface tension of water and of seawater

The two most abundant liquids on Earth are fresh water and seawater. This section gives correlations of reference data for the surface tension of both.

Surface tension of water

The surface tension of pure liquid water in contact with its vapor has been given by IAPWS^[30] as

\gamma _{\text{w}}=235.8\left(1-{\frac {T}{T_{\text{C}}}}\right)^{1.256}\left[1-0.625\left(1-{\frac {T}{T_{\text{C}}}}\right)\right]~{\text{mN/m}},

where both $T$ and the critical temperature $T C$ = 647.096 K are expressed in kelvins. The region of validity the entire vapor–liquid saturation curve, from the triple point (0.01 °C) to the critical point. It also provides reasonable results when extrapolated to metastable (supercooled) conditions, down to at least −25 °C. This formulation was originally adopted by IAPWS in 1976 and was adjusted in 1994 to conform to the International Temperature Scale of 1990.

The uncertainty of this formulation is given over the full range of temperature by IAPWS.^[30] For temperatures below 100 °C, the uncertainty is ±0.5%.

Surface tension of seawater

Nayar et al.^[31] published reference data for the surface tension of seawater over the salinity range of 20 ≤ $S$ ≤ 131 g/kg and a temperature range of 1 ≤ $t$ ≤ 92 °C at atmospheric pressure. The uncertainty of the measurements varied from 0.18 to 0.37 mN/m with the average uncertainty being 0.22 mN/m. This data is correlated by the following equation

\gamma _{\mathrm {sw} }=\gamma _{\mathrm {w} }\left(1+3.766\times 10^{-4}S+2.347\times 10^{-6}St\right)

where $γ sw$ is the surface tension of seawater in mN/m, $γ w$ is the surface tension of water in mN/m, $S$ is the reference salinity^[32] in g/kg, and $t$ is temperature in degrees Celsius. The average absolute percentage deviation between measurements and the correlation was 0.19% while the maximum deviation is 0.60%.

The range of temperature and salinity encompasses both the oceanographic range and the range of conditions encountered in thermal desalination technologies.

Data table

Surface tension of various liquids in dyn/cm against air^[33]
Mixture compositions denoted "%" are by mass
dyn/cm is equivalent to the SI units of mN/m (millinewton per meter)
Liquid	Temperature (°C)	Surface tension, $γ$
Acetic acid	20	27.60
Acetic acid (40.1%) + Water	30	40.68
Acetic acid (10.0%) + Water	30	54.56
Acetone	20	23.70
Diethyl ether	20	17.00
Ethanol	20	22.27
Ethanol (40%) + Water	25	29.63
Ethanol (11.1%) + Water	25	46.03
Glycerol	20	63.00
n-Hexane	20	18.40
Hydrochloric acid 17.7 M aqueous solution	20	65.95
Isopropanol	20	21.70
Liquid helium II	−273	^[34] 0.37
Liquid nitrogen	−196	8.85
Mercury	15	487.00
Methanol	20	22.60
n-Octane	20	21.80
Sodium chloride 6.0 M aqueous solution	20	82.55
Sucrose (55%) + water	20	76.45
Water	0	75.64
Water	25	71.97
Water	50	67.91
Water	100	58.85
Toluene	25	27.73

Gallery of effects

Breakup of a moving sheet of water bouncing off of a spoon.
Photo of flowing water adhering to a hand. Surface tension creates the sheet of water between the flow and the hand.
A soap bubble balances surface tension forces against internal pneumatic pressure.
Surface tension prevents a coin from sinking: the coin is indisputably denser than water, so it must be displacing a volume greater than its own for buoyancy to balance mass.
A daisy. The entirety of the flower lies below the level of the (undisturbed) free surface. The water rises smoothly around its edge. Surface tension prevents water filling the air between the petals and possibly submerging the flower.
A metal paper clip floats on water. Several can usually be carefully added without overflow of water.
An aluminium coin floats on the surface of the water at 10 °C. Any extra weight would drop the coin to the bottom.
A metal paperclip floating on water. A grill in front of the light has created the 'contour lines' which show the deformation in the water surface caused by the metal paper clip.

Notes

↑ In a mercury barometer, the upper liquid surface is an interface between the liquid and a vacuum containing some molecules of evaporated liquid.

References

↑ US Geological Survey (July 2015). "Surface Tension (Water Properties) – USGS Water Science School". US Geological Survey. Retrieved November 6, 2015.
1 2 3 White, Harvey E. (1948). Modern College Physics. van Nostrand. ISBN 0-442-29401-8.
↑ Bush, John W. M. (May 2004). "MIT Lecture Notes on Surface Tension, lecture 5" (PDF). Massachusetts Institute of Technology. Retrieved April 1, 2007.
↑ Bush, John W. M. (May 2004). "MIT Lecture Notes on Surface Tension, lecture 3" (PDF). Massachusetts Institute of Technology. Retrieved April 1, 2007.
↑ Bush, John W. M. (April 2004). "MIT Lecture Notes on Surface Tension, lecture 1" (PDF). Massachusetts Institute of Technology. Retrieved April 1, 2007.
↑ "Mechanical definition of surface tension". Retrieved Dec 16, 2013.
1 2 3 4 5 6 7 8 Sears, Francis Weston; Zemanski, Mark W. University Physics 2nd ed. Addison Wesley 1955
1 2 3 4 5 6 7 8 9 Pierre-Gilles de Gennes; Françoise Brochard-Wyart; David Quéré (2002). Capillarity and Wetting Phenomena—Drops, Bubbles, Pearls, Waves. Alex Reisinger. Springer. ISBN 0-387-00592-7.
↑ Butt, Hans-Jürgen; Graf, Karlheinz; Kappl, Michael (2006). "Physics and Chemistry of Interfaces": 9.
↑ Aaronson, Scott (March 2005) NP-complete Problems and Physical Reality. ACM SIGACT News
1 2 3 4 "Surface Tension by the Ring Method (Du Nouy Method)" (PDF). PHYWE. Retrieved 2007-09-08.
↑ "Surface and Interfacial Tension". Langmuir-Blodgett Instruments. Retrieved 2007-09-08.
↑ "Surfacants at interfaces" (PDF). lauda.de. Retrieved 2007-09-08.
↑ Calvert, James B. "Surface Tension (physics lecture notes)". University of Denver. Retrieved 2007-09-08.
↑ "Sessile Drop Method". Dataphysics. Archived from the original on August 8, 2007. Retrieved 2007-09-08.
↑ Vicente, C.; Yao, W.; Maris, H.; Seidel, G. (2002). "Surface tension of liquid 4He as measured using the vibration modes of a levitated drop". Physical Review B. 66 (21). Bibcode:2002PhRvB..66u4504V. doi:10.1103/PhysRevB.66.214504.
↑ "Droplet oscillations driven by an electric field". Colloids and Surfaces A: Physicochemical and Engineering Aspects. 460: 351–354. doi:10.1016/j.colsurfa.2013.12.013.
↑ "Electrically Driven Resonant Oscillations of Pendant Hemispherical Liquid Droplet and Possibility to Evaluate the Surface Tension in Real Time". Zeitschrift für Physikalische Chemie. 227. doi:10.1524/zpch.2013.0420.
↑ "Oscillations of a Hanging Liquid Drop, Driven by Interfacial Dielectric Force". Zeitschrift für Physikalische Chemie. 225: 405–411. doi:10.1524/zpch.2011.0074.
↑ Gibbs, J.W. (2002) [1876–1878], "On the Equilibrium of Heterogeneous Substances", in Bumstead, H.A.; Van Nameeds, R.G., The Scientific Papers of J. Willard Gibbs, 1, Woodbridge, CT: Ox Bow Press, pp. 55–354, ISBN 0918024773
1 2 3 4 Moore, Walter J. (1962). Physical Chemistry, 3rd ed. Prentice Hall.
1 2 3 4 5 Adam, Neil Kensington (1941). The Physics and Chemistry of Surfaces, 3rd ed. Oxford University Press.
↑ van der Waals, J.D. (1979) [1893], translated by Rowlinson, J.S., "The thermodynamic theory of capillarity under the hypothesis of a continuous variation of density", J. Stat. Phys., 20 (2): 197–200, doi:10.1007/BF01011513
↑ Cahn, J.W.; Hilliard, J.E. (1958), "Free energy of a nonuniform system. I. Interfacial free energy", J. Chem. Phys.: 258–266, doi:10.1063/1.1744102
↑ Langer, J.S.; Bar-On, M.; Miller, H.D. (1975), "New computational method in the theory of spinodal decomposition", Phys. Rev. A.: 1417–1429., doi:10.1103/PhysRevA.11.1417
↑ Gorban, A.N.; Karlin, I. V. (2016), "Beyond Navier–Stokes equations: capillarity of ideal gas", Contemporary Physics (Review article), doi:10.1080/00107514.2016.1256123
1 2 "Physical Properties Sources Index: Eötvös Constant". Retrieved 2008-11-16.
↑ Vargaftik, N. B.; Volkov, B. N.; Voljak, L. D. (1983). "International Tables of the Surface Tension of Water" (PDF). Journal of Physical and Chemical Reference Data. 12 (3): 817. Bibcode:1983JPCRD..12..817V. doi:10.1063/1.555688.
↑ G. Ertl, H. Knözinger and J. Weitkamp; Handbook of heterogeneous catalysis, Vol. 2, page 430; Wiley-VCH; Weinheim; 1997 ISBN 3-527-31241-2
1 2 International Association for the Properties of Water and Steam (June 2014). "Revised Release on Surface Tension of Ordinary Water Substance".
↑ K.G. Nayar; D. Panchanathan; G.H. McKinley & J.H. Lienhard V (November 2014). "Surface tension of seawater". J. Phys. Chem. Ref. Data. 43 (4): 43103. Bibcode:2014JPCRD..43d3103N. doi:10.1063/1.4899037.
↑ F. J. Millero; R. Feistel; D. G. Wright & T. J. McDougall (January 2008). "The composition of Standard Seawater and the definition of the Reference-Composition Salinity Scale". Deep-Sea Research Part I. 55: 50.
↑ Lange's Handbook of Chemistry (1967) 10th ed. pp 1661–1665 ISBN 0-07-016190-9 (11th ed.)
↑ On the Surface Tension of Liquid Helium II

External links

Wikimedia Commons has media related to Surface tension.

On surface tension and interesting real-world cases
Surface Tensions of Various Liquids
Calculation of temperature-dependent surface tensions for some common components
Surface tension calculator for aqueous solutions containing the ions H⁺, NH+
4, Na⁺, K⁺, Mg²⁺, Ca²⁺, SO2−
4, NO−
3, Cl⁻, CO2−
3, Br⁻ and OH⁻.
T. Proctor Hall (1893) New methods of measuring surface tension in liquids, Philosophical Magazine (series 5, 36: 385–415), link from Biodiversity Heritage Library.
The Bubble Wall (Audio slideshow from the National High Magnetic Field Laboratory explaining cohesion, surface tension and hydrogen bonds)
C. Pfister: Interface Free Energy. Scholarpedia 2010 (from first principles of statistical mechanics)
Fundamentals of surface and interfacial tension
Surface and Interfacial Tension

Branches of physics
Divisions	Applied Experimental Theoretical
Energy Motion	Thermodynamics Mechanics Classical Ballistics Lagrangian Hamiltonian Continuum Celestial Statistical Solid Fluid Quantum
Waves Fields	Gravitation Electromagnetism Optics Geometrical Physical Nonlinear Quantum Quantum field theory Relativity Special General
By speciality	Accelerator Acoustics Astrophysics Nuclear Stellar Heliophysics Solar Space Astroparticle Atomic–molecular–optical (AMO) Communication Computational Condensed matter Mesoscopic Solid-state Soft Digital Engineering Material Mathematical Molecular Nuclear Particle Phenomenology Plasma Polymer Statistical
Physics in life science	Biophysics Virophysics Biomechanics Medical physics Cardiophysics Health physics Laser medicine Medical imaging‎ Nuclear medicine Neurophysics Psychophysics
Physics with other sciences	Agrophysics Soil Atmospheric Cloud Chemical Econophysics Geophysics

Diving medicine, physiology, physics and environment

Diving
medicine

Injuries
and
disorders

Pressure

Oxygen	Freediving blackout Hyperoxia Hypoxia (medical) Oxygen toxicity
Inert gases	Atrial septal defect Avascular necrosis Decompression sickness Dysbaric osteonecrosis High-pressure nervous syndrome Hydrogen narcosis Isobaric counterdiffusion Nitrogen narcosis Taravana Uncontrolled decompression
Carbon dioxide	Hypercapnia Hypocapnia

Immersion

Treatments

Diving
physiology

Diving
physics

Diving
environment

Researchers in
diving medicine,
and physiology

Diving medical
research
organisations

Aerospace Medical Association

Divers Alert Network

Diving Diseases Research Centre

Fitness to dive

List of diving hazards and precautions

National Board of Diving and Hyperbaric Medical Technology

Naval Submarine Medical Research Laboratory

Royal Australian Navy School of Underwater Medicine

Rubicon Foundation

South Pacific Underwater Medicine Society

Undersea and Hyperbaric Medical Society

United States Navy Experimental Diving Unit

Categories: Diving medicine
Underwater diving physiology
Underwater diving physics
Physical oceanography
Glossary
Portal

This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.

Surface tension

Causes

Effects of surface tension

Water

Surfactants

Physics

Physical units

Surface area growth

Surface curvature and pressure

Floating objects

Liquid surface

Contact angles

Special contact angles

Methods of measurement

Effects

Liquid in a vertical tube

Puddles on a surface

The breakup of streams into drops

Thermodynamics

Thermodynamic theories of surface tension

Thermodynamics of soap bubbles

Influence of temperature

Influence of solute concentration

Influence of particle size on vapor pressure

Surface tension of water and of seawater

Surface tension of water

Surface tension of seawater

Data table

Gallery of effects

See also

Notes

References

External links