SSVP docking system

Sistema Stykovki i Vnutrennego Perekhoda, SSVP (Russian: Система стыковки и внутреннего перехода, System for docking and internal transfer) is a docking standard used by Soviet and Russian spacecraft,[1] sometimes called RDS for Russian Docking System. It has been used on all variants of Soyuz other than the Soyuz 7K-L3 and early flights of the Soyuz 7K-OK, as well as Progress, TKS, ATV, and on all Soviet and Russian space stations.

History

SSVP was initially conceived in 1967 by the TsKBEM design bureau for use on the then-planned OIS military space station. Though OIS never flew, in 1970 the design was selected for use on the Salyut and Almaz space stations.[1] During its first attempted use on the Soyuz 10 mission, docking was unsuccessful due to a faulty hatch, and a failure in the automatic docking system.[2] This led to a number of redesigns to reduce damage from accidental loads.[1]

In the 1980s, SSVP was further upgraded to support docking of large modules, such as the ones that would be used to construct Mir.[1] They were used to attach all pressurized modules of the Mir station, and for most spacecraft dockings (with the exception of the Space Shuttle flights, and Soyuz TM-16, which used the APAS-89 docking mechanisms located on Kristall and the Mir Docking Module.[3])

The modern version of SSVP is SSVP-G4000.[1] The Russian segment of the International Space Station features four available passive SSVP-G4000 ports, located on Zvezda-aft, Rassvet, Poisk, and Pirs. An additional port, on Zarya-nadir, was used to dock Rassvet. In addition to Russian spacecraft, the SSVP was also used on the European Automated Transfer Vehicle, which docked to the aft port of Zvezda. These ports were provided by Russia in exchange for the Data Management System, supplied by ESA for use in Zvezda.[4][5]

An upgraded version, designed for reusability and to provide a wider tunnel, is planned for use on the next-generation Federation spacecraft.[6]

Design

SSVP Drogue
SSVP Probe

SSVP consists of two components; an active probe, and a passive drogue. The probe enters the drogue, and its tip is grasped by soft-capture latches which are then retracted using electrically-driven motors to provide close alignment. Eight hard-capture locks then firmly attach the two spacecraft. After hard docking, the pressure between spacecraft is equalized using the Interface Leak Check System.[1][7]

The port contains a transfer tunnel, with an internal diameter of 800 mm. The ring surrounding this tunnel also includes a number of connectors, providing for transfer of power, data, and fuel between two docked vehicles.[1]

Hybrid

A "hybrid" version, combining the design of SSVP and APAS-95, is also available, used for permanent docking of space station modules. This version uses the probe-and-drogue design of the standard SSVP, but with a hard-dock collar from APAS-95. The APAS-95 collar has twelve latches instead of the eight of standard SSVP. This variant is known as SSVP-M8000.[7]

These hybrid SSVP ports are used to permanently connect Zarya to Zvezda, and Pirs and Poisk to Zvezda.[7]

See also

References

  1. 1 2 3 4 5 6 7 "Docking systems". Russian Space Web. Retrieved 8 February 2016.
  2. ↑ "Soyuz 10". Retrieved 8 February 2016.
  3. ↑ "Soyuz TM-16". Retrieved 8 February 2016.
  4. ↑ "N° 50–2000: International Space Station docks successfully with Zvezda module". European Space Agency. Retrieved 8 February 2016.
  5. ↑ "Automated Transfer Vehicle (ATV) Structural and Thermal Model Testing at ESTEC" (PDF). European Space Agency. Retrieved 8 February 2016.
  6. ↑ "PTK spacecraft to feature improved docking port". Russian Space Web. Retrieved 8 February 2016.
  7. 1 2 3 John Cook; Valery Aksamentov; Thomas Hoffman; Wes Bruner. "ISS Interface Mechanisms and their Heritage" (PDF). Boeing. Retrieved 8 February 2016.
This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.