Pore water pressure

Pore water pressure (sometimes abbreviated to pwp) refers to the pressure of groundwater held within a soil or rock, in gaps between particles (pores). Pore water pressures in below the phreatic level (see also groundwater) are measured in piezometers. The vertical pore water pressure distribution in aquifers can generally be assumed to be close to hydrostatic.

In the unsaturated zone, the pore pressure is determined by capillarity and is also referred to as tension, suction, or matric pressure. Pore water pressures under unsaturated conditions (vadose zone) are measured in with tensiometers. Tensiometers operate by allowing the pore water to come into equilibrium with a reference pressure indicator through a permeable ceramic cup placed in contact with the soil.

Pore water pressure is vital in calculating the stress state in the ground soil mechanics, from Terzaghi's expression for the effective stress of a soil.

General principles

Pressure develops due to:

Pore water pressure below the water table

A vibrating wire piezometer. The vibrating wire converts the fluid pressures into equivalent frequency signals that are then recorded.

The buoyancy effects of water have a large impact on certain soil properties, such as the effective stress present at any point in a soil medium. Consider an arbitrary point five meters below the ground surface. In dry soil, particles at this point experience a total overhead stress equal to the depth underground (5 meters), multiplied by the specific weight of the soil. However, when the local water table height is within said five meters, the total stress felt five meters below surface is decreased by the product of the height of the water table in to the five meter area, and the specific weight of water, 9.81 kN/m^3. This parameter is called the effective stress of the soil, basically equal to the difference in a soil's total stress and pore water pressure. The pore water pressure is essential in differentiating a soil's total stress from its effective stress. A correct representation of stress in soil is necessary for accurate field calculations in a variety of engineering trades.[2]

Equation for calculation

When there is no flow, the pore pressure at depth, hw, below the water surface is:[3]

,

where:

Measurement methods and standards

The standard method for measuring pore water pressure below the water table employs a piezometer, which measures the height to which a column of the liquid rises against gravity; i.e., the static pressure (or piezometric head) of groundwater at a specific depth.[4] Piezometers often employ electronic pressure transducers to provide data. The United States Bureau of Reclamation has a standard for monitoring water pressure in a rock mass with piezometers. It sites ASTM D4750, "Standard Test Method for Determining Subsurface Liquid Levels in a Borehole or Monitoring Well (Observation Well)".[5]

Pore water pressure above the water table

Electronic tensiometer probe: (1) porous cup; (2) water-filled tube; (3) sensor-head; (4) pressure sensor

At any point above the water table, in the vadose zone, the effective stress is approximately equal to the total stress, as proven by Terzaghi's principle. Realistically, the effective stress is greater than the total stress, as the pore water pressure in these partially saturated soils is actually negative. This is primarily due to the surface tension of pore water in voids throughout the vadose zone causing a suction effect on surrounding particles. This capillary action is the "upward movement of water through the vadose zone" (Coduto, 266).[6] Capillary effects in soil are more complex than in free water due to the randomly connected void space and particle interference through which to flow; regardless, the height of this zone of capillary rise, where negative pore water pressure is generally peaks, can be closely approximated by a simple equation. The height of capillary rise is inversely proportional to the diameter of void space in contact with water. Therefore, the smaller the void space, the higher water will rise due to tension forces. Sandy soils consist of more coarse material with more room for voids, and therefore tends to have a much shallower capillary zone than do more cohesive soils, such as clays and silts.[6]

Equation for calculation

If the water table is at depth dw, then the pore pressure at the ground surface is:[3]

,

where:

and the pore pressure at depth, z, below the surface is:

,

where:

Measurement methods and standards

A tensiometer is an instrument used to determine the matric water potential () (soil moisture tension) in the vadose zone.[7] An ISO standard, "Soil quality — Determination of pore water pressure — Tensiometer method", ISO 11276:1995, "describes methods for the determination of pore water pressure (point measurements) in unsaturated and saturated soil using tensiometers. Applicable for in situ measurements in the field and, e. g. soil cores, used in experimental examinations." It defines pore water pressure as "the sum of matric and pneumatic pressures".[8]

Matric pressure

The amount of work that must be done in order to transport reversibly and isothermally an infinitesimal quantity of water, identical in composition to the soil water, from a pool at the elevation and the external gas pressure of the point under consideration, to the soil water at the point under consideration, divided by the volume of water transported.[9]

Pneumatic pressure

The amount of work that must be done in order to transport reversibly and isothermally an infinitesimal quantity of water, identical in composition to the soil water, from a pool at atmospheric pressure and at the elevation of the point under consideration, to a similar pool at an external gas pressure of the point under consideration, divided by the volume of water transported.[9]

See also

References

  1. ↑ Mitchell, J.K. "Components of Pore Water Pressure and their Engineering Significance" (PDF). Retrieved 2013-02-17.
  2. ↑ Das, Braja (2011). Principles of Foundation Engineering. Stamford, CT: Cengage Learning. ISBN 9780495668107.
  3. 1 2 Wood, David Muir. "Pore water pressure". GeotechniCAL reference package. Bristol University. Retrieved 2014-03-12.
  4. ↑ Dunnicliff, John (1993) [1988]. Geotechnical Instrumentation for Monitoring Field Performance. Wiley-Interscience. p. 117. ISBN 0-471-00546-0.
  5. ↑ Materials Engineering and Research Laboratory. "Procedure For Using Piezometers to Monitor Water Pressure in a Rock Mass" (PDF). USBR 6515. U.S. Bureau of Reclamation. Retrieved 2014-03-13.
  6. 1 2 Coduto, Donald; et al. (2011). Geotechnical Engineering Principles and Practices. NJ: Pearson Higher Education, Inc. ISBN 9780132368681.
  7. ↑ Rawls, W.J., Ahuja, L.R., Brakensiek, D.L., and Shirmohammadi, A. 1993. Infiltration and soil water movement, in Maidment, D.R., Ed., Handbook of hydrology, New York, NY, USA, McGraw-Hill, p. 5.1–5.51.
  8. ↑ ISO (1995). "Soil quality -- Determination of pore water pressure -- Tensiometer method". ISO 11276:1995. International Standards Organization. Retrieved 2014-03-13.
  9. 1 2 BS 7755 1996; Part 5.1
This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.