Plasterwork

Plasterwork refers to construction or ornamentation done with plaster, such as a layer of plaster on an interior or exterior wall structure, or plaster decorative moldings on ceilings or walls. This is also sometimes called pargeting. The process of creating plasterwork, called plastering or rendering, has been used in building construction for centuries. For the art history of three-dimensional plaster, see stucco.

History

The earliest plasters known to us were lime-based. Around 7500 BC, the people of 'Ain Ghazal in Jordan used lime mixed with unheated crushed limestone to make plaster which was used on a large scale for covering walls, floors, and hearths in their houses. Often, walls and floors were decorated with red, finger-painted patterns and designs. In ancient India and China, renders in clay and gypsum plasters were used to produce a smooth surface over rough stone or mud brick walls, while in early Egyptian tombs, walls were coated with lime and gypsum plaster and the finished surface was often painted or decorated.

Modelled stucco was employed throughout the Roman Empire. The Romans used mixtures of lime and sand to build up preparatory layers over which finer applications of gypsum, lime, sand and marble dust were made; pozzolanic materials were sometimes added to produce a more rapid set. Following the fall of the Roman Empire, the addition of marble dust to plaster to allow the production of fine detail and a hard, smooth finish in hand-modelled and moulded decoration was not used until the Renaissance. Around the 4th century BC, the Romans discovered the principles of the hydraulic set of lime, which by the addition of highly reactive forms of silica and alumina, such as volcanic earths, could solidify rapidly even under water. There was little use of hydraulic mortar after the Roman period until the 18th century.

Plaster decoration was widely used in Europe in the Middle Ages where, from the mid-13th century, gypsum plaster was used for internal and external plaster. Hair was employed as reinforcement, with additives to assist set or plasticity including malt, urine, beer, milk and eggs.

14th century

In the 14th century, decorative plasterwork called pargeting was being used in South-East England to decorate the exterior of timber-framed buildings. This is a form of incised, moulded or modelled ornament, executed in lime putty or mixtures of lime and gypsum plaster. During this same period, terracotta was reintroduced into Europe and was widely used for the production of ornament.

15th century

In the mid-15th century, Venetian skilled workers developed a new type of external facing, called marmorino made by applying lime directly onto masonry.

16th century

In the 16th century, a new highly decorative type of decorative internal plasterwork, called scagliola, was invented by stuccoists working in Bavaria. This was composed of gypsum plaster, animal glue and pigments, used to imitate coloured marbles and pietre dure ornament. Sand or marble dust, and lime, were sometimes added. In this same century, the sgraffito technique, also known as graffito or scratchwork was introduced into Germany by Italian artists, combining it with modelled stucco decoration. This technique was practised in antiquity and was described by Vasari as being a quick and durable method for decorating building facades. Here, layers of contrasting lime plaster were applied and a design scratched through the upper layer to reveal the colour beneath.

17th century

The 17th century saw the introduction of different types of internal plasterwork. Stucco marble was an artificial marble made using gypsum (sometimes with lime), pigments, water and glue. Stucco lustro was another a form of imitation marble (sometimes called stucco lucido) where a thin layer of lime or gypsum plaster was applied over a scored support of lime, with pigments scattered on surface of the wet plaster.

18th century

The 18th century gave rise to renewed interest in innovative external plasters. Oil mastics introduced in the UK in this period included a "Composition or stone paste" patented in 1765 by David Wark. This was a lime-based mix and included "oyls of tar, turpentine and linseed" besides many other ingredients. Another "Composition or cement", including drying oil, was patented in 1773 by Rev. John Liardet. A similar product was patented in 1777 by John Johnson. Widely used by the architect Robert Adam who in turn commissioned George Jackson to produce reverse-cut boxwood moulds (many of which to Adam designs). Jackson formed an independent company which still today produces composition pressings and retains a very large boxwood mould collection.

In 1774, in France, a mémoire was published on the composition of ancient mortars. This was translated into English as "A Practical Essay on a Cement, and Artificial Stone, justly supposed to be that of the Greeks and Romans" and was published in the same year. Following this, and as a backlash to the disappointment felt due to the repeated failure of oil mastics, in the second half of the 18th century water-based renders gained popularity once more. Mixes for renders were patented, including a "Water Cement, or Stucco" consisting of lime, sand, bone ash and lime-water (Dr Bryan Higgins, 1779). Various experiments mixing different limes with volcanic earths took place in the 18th century. John Smeaton (from 1756) experimented with hydraulic limes and concluded that the best limes were those fired from limestones containing a considerable quantity of clay]ey material. In 1796, Revd James Parker patented Parker's "Roman Cement". This was a hydraulic cement which, when mixed with sand, could be used for stucco. It could also be cast to form mouldings and other ornaments. It was however of an unattractive brown colour, which needed to be disguised by surface finishes.

19th century

Natural cements were frequently used in stucco mixes during the 1820s. The popularisation of Portland cement changed the composition of stucco, as well as mortar, to a harder material. The development of artificial cements had started early in the 19th century. In 1811, James Frost took out a patent for an artificial cement obtained by lightly calcining ground chalk and clay together. The French Engineer Louis Vicat in 1812–1813 experimented with calcining synthetic mixtures of limestone and clay, a product he introduced in 1818. In 1822, in the UK, James Frost patented (another?) process, similar to Vicat's, producing what he called "British cement". Portland cement, patented in 1824 by Joseph Aspdin, was called so because it was supposed to resemble Portland stone. Aspdinís son William, and later Isaac Johnson, improved the production process. A product, very similar to modern Portland cement, was available from about 1845, with other improvements taking place in the following years.

Thus, after about 1860, most stucco was composed primarily of Portland cement, mixed with some lime. This made it even more versatile and durable. No longer used just as a coating for a substantial material like masonry or log, stucco could now be applied over wood or metal lath attached to a light wood frame. With this increased strength, it ceased to be just a veneer and became a more integral part of the building structure. Early 19th century rendered façades were colour-washed with distemper; oil paint for external walls was introduced around 1840.

The 19th century also saw the revival of the use of oil mastics. In the UK, patents were obtained for "compositions" in 1803 (Thomas Fulchner), 1815 (Christopher Dihl) and 1817 (Peter Hamelin). These oil mastics, as the ones before them, also proved to be short-lived.

Moulded or cast masonry substitutes, such as cast stone and poured concrete, became popular in place of quarried stone during the 19th century. However, this was not the first time "artificial stone" had been widely used. Coade Stone, a brand name for a cast stone made from fired clay, had been developed and manufactured in England from 1769 to 1843 and was used for decorative architectural elements. Following the closure of the factory in South London, Coade stone stopped being produced, and the formula was lost. By the mid 19th century manufacturing centres were preparing cast stones based on cement for use in buildings. These were made primarily with a cement mix often incorporating fine and coarse aggregates for texture, pigments or dyes to imitate colouring and veining of natural stones, as well as other additives.

Also in the 19th century, various mixtures of modified gypsum plasters, such as Keene's cement, appeared. These materials were developed for use as internal wall plasters, increasing the usefulness of simple plaster of Paris as they set more slowly and were thus easier to use.

A plasterer covering a wall, using a hawk (in his left hand) and trowel (in his right hand)

Tools and materials

Tools and materials include trowels, floats, hammers, screeds, a hawk, scratching tools, utility knives, laths, lath nails, lime, sand, hair, plaster of Paris, a variety of cements, and various ingredients to form color washes.

While most tools have remained unchanged over the centuries, developments in modern materials have led to some changes. Trowels, originally constructed from steel, are now available in a polycarbonate material that allows the application of certain new, acrylic-based materials without staining the finish. Floats, traditionally made of timber (ideally straight-grained, knot-free, yellow pine), are often finished with a layer of sponge or expanded polystyrene.

Laths

Lath seen from the back with brown coat oozing through

Traditionally, plaster was laid onto laths, rather than plasterboard as is more commonplace nowadays.

Wooden laths are narrow strips of straight-grained wood depending on availability of species in lengths of from two to four or five feet to suit the distances at which the timbers of a floor or partition are set. Laths are about an inch wide, and are made in three thicknesses; single (18 to 316 inch thick), lath and a half (14 inch thick), and double (3812 inch thick).

The thicker laths should be used in ceilings, to stand the extra strain (sometimes they were doubled for extra strength), and the thinner variety in vertical work such as partitions, except where the latter will be subjected to rough usage, in which case thicker laths become necessary. Laths are usually nailed with a space of about 38 of an inch between them to form a key for the plaster.

Laths were formerly all made by hand. Most are now made by machinery and are known as sawn laths, those made by hand being called rent or riven laths. Rent laths give the best results, as they split in a line with the grain of the wood, and are stronger and not so liable to twist as machine-made laths, some of the fibers of which are usually cut in the process of sawing.

Laths must be nailed so as to break joint in bays three or four feet wide with ends butted one against the other. By breaking the joints of the lathing in this way, the tendency for the plaster to crack along the line of joints is diminished and a better key is obtained. Every lath should be nailed at each end and wherever it crosses a joist or stud. All timbers over three inches (76 mm) wide should be counter-lathed, that is, have a fillet or double lath nailed along the centre upon which the laths are then nailed. This is done to preserve a good key for the plaster.

Walls liable to damp are sometimes battened and lathed to form an air cavity between the damp wall and the plastering.

Lathing in metal, either in wire or in the form of perforated galvanised sheets, is now extensively used on account of its fireproof and lasting quality. There are many kinds of this material in different designs, the best known in England being the Jhilmil, the Bostwick, Lathing, and Expanded Metal lathing. The two last-named are also widely used in America.

Lathing nails are usually of iron, cut, wrought or cast, and in the better class of work they are galvanized to prevent rusting. Zinc nails are sometimes used, but are costly.

Lime plastering

Lime plastering is composed of lime, sand, hair and water in proportions varying according to the nature of the work to be done.

The lime mortar principally used for internal plastering is that calcined from chalk, oyster shells or other nearly pure limestone, and is known as fat, pure, chalk or rich lime. Hydraulic limes are also used by the plasterer, but chiefly for external work.

Perfect slaking of the calcined lime before being used is very important as, if used in a partially slaked condition, it will "blow" when in position and blister the work. Lime should therefore be run as soon as the building is begun, and at least three weeks should elapse between the operation of running the lime and its use.

Cheefon

Hair is used in plaster as a binding medium, and gives tenacity to the material. Traditionally horsehair was the most commonly used binder, as it was easily available before the development of the motor-car. Hair functions in much the same way as the strands in fiberglass resin, by controlling and containing any small cracks within the mortar while it dries or when it is subject to flexing.

Ox-hair, which is sold in three qualities, is now the kind usually specified; but horsehair, which is shorter, is sometimes substituted or mixed with the ox-hair in the lower qualities. Good hair should be long (In the UK cow and horse hair of short and long lengths is used), and left greasey (lanolin grease) because this protects against some degradation when introduced into the very high alkaline plaster.[1] Before use it must be well beaten, or teased, to separate the lumps. In America, goats' hair is frequently used, though it is not so strong as ox-hair. The quantity used in good work is one pound of hair to two or three cubic feet of coarse stuff (in the UK up to 12 kg per metric cube). Hair reinforcement in lime plaster is common and many types of hair and other organic fibres can be found in historic plasters [4]. However, organic material in lime will degrade in damp environments particularly on damp external renders.[5] This problem has given rise to the use of polyprolene fibres in new lime renders [6]

Manila hemp fiber has been used as a substitute for hair. Plaster for hair slabs made with manila hemp fiber broke at 195 lb (88 kg), plaster mixed with sisal hemp at 150 lb (68 kg), jute at 145 lb (66 kg), and goats' hair at 144 lb (65 kg). Another test was made in the following manner. Two barrels of mortar were made up of equal proportions of lime and sand, one containing the usual quantity of goats' hair, and the other Manila fiber. After remaining in a dry cellar for nine months the barrels were opened. It was found that the hair had been almost entirely eaten away by the action of the lime, and the mortar consequently broke up and crumbled quite easily. The mortar containing the Manila hemp, on the other hand, showed great cohesion, and required some effort to pull it apart, the hemp fiber being undamaged.

Sand/aggregate

For fine plasterer's sand-work, special sands are used, such as silver sand, which is used when a light color and fine texture are required. In England this fine white sand is procured chiefly from Leighton Buzzard; also in England many traditional plasters had crushed chalk as the aggreate, this made a very flexible plaster suitable for timber frame buildings.

For external work Portland cement is undoubtedly the best material on account of its strength, durability, and weather resisting external properties, but not on historic structures that are required to flex and breathe; for this, lime without cement is used.[2]

Sawdust has been used as a substitute for hair and also instead of sand as an aggregate. Sawdust will enable mortar to stand the effects of frost and rough weather. It is useful sometimes for heavy cornices and similar work, as it renders the material light and strong. The sawdust should be used dry. The sawdust is used to bind the mix sometimes to make it go further.

Methods

The first coat or rendering is from 1/2 to 3/4 inches thick, and is mixed in the proportions of from one part of cement to two of sand to one part to five of sand. The finishing or setting coat is about 3/16 inches thick, and is worked with a hand float on the surface of the rendering, which must first be well wetted.

External plastering

Stucco is a term loosely applied to nearly all kinds of external plastering, whether composed of lime or of cement. At the present time it has fallen into disfavor, but in the early part of the 19th century a great deal of this work was done. Cement has largely superseded lime for this work. The principal varieties of stucco are common, rough, trowelled and bastard. .

Roughcast or pebbledash plastering is a rough form of external plastering in much use for country houses. In Scotland it is termed "harling". It is one of the oldest forms of external plastering. In Tudor times it was employed to fill in between the woodwork of half-timbered framing. When well executed with good material this kind of plastering is very durable.

Roughcasting is performed by first rendering the wall or laths with a coat of well-haired coarse stuff composed either of good hydraulic lime or of Portland cement. This layer is well scratched to give a key for the next coat. The second coat is also composed of coarse stuff knocked up to a smooth and uniform consistency. Two finish two techniques can be used:

Sgraffito (scratched ornament)

Sgraffito is the name for scratched ornament in plaster. Scratched ornament is the oldest form of surface decoration, and is much used on the continent of Europe, especially in Germany and Italy, in both external and internal situations.

Properly treated, the work is durable, effective and inexpensive. A first coat or rendering of Portland cement and sand, in the proportion of one to three, is laid on about an inch thick; then follows the color coat, sometimes put on in patches of different tints as required for the finished design. When this coat is nearly dry, it is finished with a smooth-skimming, 1/12 to 1/8 inches thick, of Parian, selenitic or other fine cement or lime, only as much as can be finished in one day being laid on.

Then by pouncing through the pricked cartoon, the design is transferred to the plastered surface. Broad spaces of background are now exposed by removing the finishing coat, thus revealing the colored plaster beneath, and following this the outlines of the rest of the design are scratched with an iron knife through the outer skimming to the underlying tinted surface.

Sometimes the coats are in three different colors, such as brown for the first, red for the second, and white or grey for the final coat. The pigments used for this work include Indian red, Turkey red, Antwerp blue, German blue, umber, ochre, purple brown, bone black or oxide of manganese for black. Combinations of these colors are made to produce any desired tone.

Coats

Plasters are applied in successive coats or layers on walls or lathing and gains its name from the number of these coats.

The process for three coat work is as follows:

The composition of an interior three coat plaster:

The hard cements used for plastering, such as Parian, Keene's, and Martin's, are laid generally in two coats, the first of cement and sand 1/2 to 3/4 inches thick, the second or setting coat of neat cement about 1/8 inch thick. These and similar cements have gypsum as a base, to which a certain proportion of another substance, such as alum, borax or carbonate of soda, is added, and the whole baked or calcined at a low temperature. The plaster they contain causes them to set quickly with a very hard smooth surface, which may be painted or papered within a few hours of its being finished.

In Australia, plaster or cement render that is applied to external brickwork on dwellings or commercial buildings can be one or two coats. In two coat render a base coat is applied with a common mix of 4 parts sand to one part cement and one part dehydrated lime and water to make a consistent mortar. Render is applied using a hawk and trowel and pushed on about 12 mm thick to begin. For two coat, some plasterers apply two full depth bands of render (one at the base of the wall and one around chest height) which are screed plumb and square and allowed to dry while applying the first coat over the remaining exposed wall. The render is then scratched to provide a key for the second coat. This method allows the rest of the wall to be rendered and screed off without the need to continually check if the second coat is plumb. Alternatively, both coats can be applied with the plasterer using a t-bar to screed the final coat until it is plumb straight and square. The first method is generally used where quality of finish is at a premium. The second method is quicker but can be several millimeters out of plumb. The second coat can be a slightly weaker mix 5/1/1, or the same as the base coat with maybe a water proofer in the mix added to the water to minimize efflorescence (rising of salts). Some plasterers used lime putty in second coat instead of dehydrated lime in the render. The mortar is applied to about 5 mm thick and when the render hardens is screeded off straight. A wood float or plastic float is used to rub down the walls. Traditionally, water is splashed on walls using a coarse horsehair plasterers brush followed by immediately rubbing the float in a circular or figure 8 motion although a figure of 8 can leave marks. Many modern plasterers use a hose with a special nozzle with a fine mist spray to dampen walls when rubbing up (using a wood float to bring a consistent finish). Using a hose brings a superior finish and is more consistent in colour as there is more chance in catching the render before it has a chance to harden too much. After the work area is floated, the surface is finished with a wet sponge using the same method as floating with a wood float, bringing sand to the surface to give a smooth consistent finish.

Materials used in the render are commonly local sands with little clay content with fine to coarse grains. Sand finish is common for external render and may be one or two coats. Plasterers use a t-bar to screed the walls until it is plumb straight and square. Two coat is superior as, although more expensive, it gives a more consistent finish and less chance of becoming drummy or cracking. Drummy is a term used to describe when the render doesn't bond completely with the wall, either because the wall is too smooth, a coat is too thick or by being floated when the render has hardened too much, leaving an air space that makes a drumming sound when a metal tool is "rubbed" over it.

For internal walls, two coats is the standard and follows the same method as for external rendering but with a weaker mix of five or six sand to one cement and one lime. However, instead of being finished with a sponge, the second coat is left rough and sometimes will be scored by nails inserted in the float. After drying, the surface is then scraped to remove loose grains of sand before plastering. If the walls are concrete, a splash coat is needed to ensure bonding. A splash coat is a very wet mix of two parts cement to one part sand that is "splashed" on the wall using the plasterers brush until the wall is covered. Special mixes are sometimes required for architectural or practical reasons. For example, A hospitals x-ray room will be rendered with a mix containing Barium sulfate to make the walls impervious to x-rays.

Moldings

Plain, or unenriched, moldings are formed with a running mold of zinc cut to the required profile a process that has remained the same for over 200 years.

Enrichments may be moldings added after the main outline molding is set, and are cast in molds made of gelatin or plaster of Paris.

Cracks

Cracks in plastering may be caused by settlement of the building, by the use of inferior materials or by bad workmanship.

However, due to none of these, cracks may yet ensue by the too fast drying of the work, caused through the laying of plaster on dry walls which suck from the composition the moisture required to enable it to set, by the application of external heat or the heat of the sun, by the laying of a coat upon one which has not properly set, the cracking in this case being caused by unequal contraction, or by the use of too small a proportion of sand.

Traditionally, crack propagation was arrested by stirring chopped horsehair thoroughly into the plaster mix.

Slabs

finished with a thin setting coat or slab. In some cases, with fireproof ceilings, for instance, the metal lathing are hung up with wire hangers so as to allow a space of several inches between the soffit of the concrete floor and the ceiling. For partitions metal laths are grouted in with semi-fluid plaster. Where very great strength is required, the work may be reinforced by small iron rods through the slabs. This forms a very strong and rigid partition which is at the same time fire-resisting and of lightweight, and when finished measures only from two to four inches (102 mm) thick. So strong is the result that partitions of this class only two or three inches (76 mm) thick were used for temporary cells for prisoners at Newgate Gaol during the rebuilding of the new sessions house in the Old Bailey in London.

The slabs may be obtained either with a keyed surface, which requires finishing with a setting coat when the partition or ceiling is in position, or a smooth finished face, which may be papered or painted immediately the joints have been carefully made.

Fibrous plaster

Fibrous plaster is given by plasterers the suggestive name "stick and rag", and this is a rough description of the material, for it is a fibrous composed of plaster laid upon a backing of canvas stretched on wood. It is much used for moldings, circular and enriched casings to columns and girders and ornamental work, which is worked in the shop and fixed in position.

Desachy, a French modeler, took out in 1856 a patent for "producing architectural moldings, ornaments and other works of art, with surfaces of plaster," with the aid of plaster, glue, wood, wire, and canvas or other woven fabric.

The modern use of this material may be said to have started then, but the use of fibrous plaster was known and practiced by the Egyptians long before the Christian era; for ancient coffins and mummies still preserved prove that linen stiffened with plaster was used for decorating coffins and making masks. Cennino Cennini, writing in 1437, says that fine linen soaked in glue and plaster and laid on wood was used for forming grounds for painting.

Canvas and mortar were in general use in Great Britain up to the middle of the 20th century. This work is also much used for temporary work, such as exhibition buildings.

Plastering

Modern interior plastering techniques

There are two main methods in USA used in construction of the interior walls of modern homes, plasterboard, also called drywall, and veneer plastering.

In plasterboard a specialized form of sheet rock known as "greenboard" (because on the outer paper coating is greenish) is screwed onto the wall-frames (studs) of the home to form the interior walls. At the place where the two edges of wallboards meet there is a seam. These seams are covered with mesh tape and then the seams and the screw heads are concealed with the drywall compound to make the wall seem as one uniform piece. The drywall plaster is a thick paste. Later this is painted or wallpapered over to hide the work. This process is typically called "taping" and those who use drywall are known as "tapers".

Veneer plastering covers the entire wall with thin liquid plaster, uses a great deal of water and is applied very wet. The walls intended to be plastered are hanged with "Blueboard" (named as such for the industry standard of the outer paper being blue-grey in color). This type of sheet rock is designed to absorb some of the moisture of the plaster and thus allow it to cling the plaster better before it sets.

Veneer plastering is a one-shot one-coat application; taping usually requires sanding and then adding another coat, since the compound shrinks as it dries.

Traditional plastering

The plasterer usually shows up after the hangers have finished building all the internal walls, by attaching blueboard over the frames of the house with screws. The plasterer is usually a subcontractor working in crews that average about three veterans and one laborer. The job of the laborer is to set up ahead of and clean up behind the plasterers, so they can concentrate on spreading the "mud" on the walls.

Laborer's tasks

Plasterer's tasks

Normally the contractor has already supplied all the bags of Gypsum plaster that will be needed, as well as any external supply of water if the house is not yet connected. The plastering crew needs to bring their own tools and equipment and sometimes supply their own bead.

The Tasks that the plasterer is usually expected to accomplish.

The plasterer usually must first staple or tack Cornerbead onto every protruding (external) corner of the inside of the house. Care is taken to make sure this makes the wall look straight and is more of a skill of the eye than anything else.

The plasterer needs to fill a 5-gallon bucket partway with water. From this bucket he hangs his trowel or trowels and places into it various tools.

Most plasterers have their own preference for the size of the trowel they use. some wield trowels as large as 20 inches long but the norm seems to be a 16"×5". From my experience the preferred brand is a Marshalltown stainless steel. They have a brassy luster to them, a rubber handle and won't pit or rust if accidentally left in water overnight while others prefer a regular steal trowel which requires more maintenance but lasts for quite a long time and the pitting can give it a "bite" that helps when "finishing" (the last pass when the plaster is setting).

Into the bucket also goes a large brush used to splash water onto the wall and to clean his tools, a paint brush for smoothing corners, and a corner bird for forming corners (though many share one good bird to keep the room harmonious).

These tool buckets are first kept near the mix table and then as the plaster starts to set are moved closer to the wall that is being worked on. Time becomes a big factor here as once the plaster starts to harden (set) it will do so fairly rapidly and the plasterer has a small margin of error to get the wall smooth.

Onto the mixing table the plasterer usually sets his "hawk" so it will be handy when he needs to grab it and to keep dirt off of it. Any debris in the plaster can become a major nuisance.

Plasterers will typically divide a room, (especially a large or high-ceilinged wall) into top and bottom. The one working on top will do from the ceiling's edge to about belly height and work off a milk crate for an 8-foot (2.4 m) ceiling, or work off stilts for 12-foot-high rooms. For cathedral ceilings or very high walls, staging is set up and one works topside, the others further below.

Typically done with the laborer. No plaster globs left on the floors, walls or corner bead edges. (They will show up if painted and interfere with flooring and trim). Remove or neatly stack all trash.

All rooms and walls are inspected for cracking and dents or scratches that may have been caused from others bumping into the walls. They are also inspected to make sure no bumps are left on the walls from splashed plaster or water. All rooms are checked to make sure all plaster is knocked out of the outlets so the electrician can install the sockets and to make sure no tools are left behind. This leaves the walls ready for the painters and finishers to come in and do their trade.

Interior plastering techniques

Smooth

The home owner and the plasterer's boss will usually decide beforehand what styles they will use in the house. Typically walls are smooth and sometimes ceilings. Usually a homeowner will opt to have the ceilings use a "texture" technique as it is much easier, faster, and thus cheaper than a smooth ceiling.

The plasterer quotes prices based on techniques to be used and board feet to be covered to the contractor or homeowner before work begins. The board feet is obtained by the hangers or estimated by the head subcontractor by counting the wallboards that come in an industry standard of 8' to 12' long. He then adds in extra expenses for soffits and cathedral ceilings.

Typically if the ceiling is to be smooth it is done first, before the walls. If it is to be textured, it is done after the walls.

The reason for this is that invariably when a ceiling is being worked on plaster will fall and splash onto the walls. However a texture mix doesn't need to be smoothed out when it starts to set:

The first thing the plasterer tends to do is go over all the mesh-taped seams of the walls he is about to cover; in a very thin swatch. The wallboard draws moisture out of this strip so when the plasterer goes over it again when doing the rest of the wall it will not leave an indented seam that needs further reworking.

He then fills in the area near the ceiling so he will not have to stretch to reach it during the rest of the wall; And he forms the corner with his bird. This saves much needed time as this process is a race against the chemical reaction.

From the mix table the plasterer scoops some "mud" onto the center of his hawk with his trowel. Holding the hawk in his off-hand and his trowel in his primary the plasterer then scoops a bulging roll of plaster onto his trowel. this takes a bit of practice to master, especially with soupy mixes.

Then holding the trowel parallel to the wall and at a slight angle of the wrist he tries to uniformly roll the plaster onto the wall. In a manner similar to a squeegee. He starts about an inch above the floor and works his way upwards to the ceiling. Care is taken to be uniform as possible as it helps in the finishing phase.

Depending on the setting time of the plaster. once the moisture of the plaster starts to be drawn by the board a second pass is made. this is called knocking down. it is much like applying paint with a roller in wrist action and purpose. to smooth out any lines and fill in any major voids that will make extra work once the plaster starts to truly set. very little pressure is applied and the trowel is kept relatively flat towards the wall.

Sometimes an accelerant will be added to a mix to hasten the time delay from the initial mixing phase to when the plaster starts to set. This is normally done on cold days when setting is delayed or for small jobs to minimize the wait.

Once the plaster is on the wall and starts to set (this can be determined by the table that sets first), the plasterer gingerly sprinkles water onto the wall; this helps to stall the setting and to create a slip. He then uses his trowel and often a wetted felt brush held in the opposite hand and lightly touching the wall ahead of the trowel to work this slip into any small gaps (known as "catfaces") in the plaster as well as smooth out the rough lay-on and flatten any air bubbles that formed during setting.

This is a crucial time because if the wall gets too hard it is nearly impossible to fill in any gaps as the slip will no longer set with the wall and will instead just dry and fall out. This leads to the need of what is called "grinding" as one must go over the hard wall again and again trying to smooth out the hardened wall and any major catfaces must be filled in with a contour putty, joint compound, or reworked by blending in a fresh, thin coat.

The finished wall will look glossy and uniformly flat and is smooth to the touch. After a few days it will become chalky white and can then be painted over.

From the time the bags are dumped into the barrel to when the wall is completely set is called a mix. Varying on the technique used and whether accelerant or retardant is added, a mix typically lasts about two hours.

The final moments are the most frantic if it is smooth or if the mix sets quicker than anticipated. If this happens it is said the mix has "snapped" and is normally due to using old product or various types of weather (humidity or hot days can cause plaster to set quicker). Normally only three or four mixes are done in a day as plastering is very tiring and not as effective under unnatural lighting in the months with early dusk.

Plastering is done year round but unique problems may arise from season to season. In the summer, the heat tends to cause the plaster to set faster. The plaster also generates its own heat and houses can become quite hellish. Typically the plaster crew will try to arrive at the house well before dawn.

In winter months, short days cause the need of artificial lighting. At certain angles these lights can make even the smoothest wall look like the surface of the moon. Another dilemma in the winter months is needing to use propane jet heaters (which can stain the plaster yellowish but do not otherwise hurt it), not just to keep the plasterers warm but to also prevent the water in the mix from freezing and generating ice crystals before the plaster has time to set. Also if the water hose is not thoroughly drained before leaving it can freeze over night and be completely stopped up in the morning.

Textured

Texturing is usually reserved for closets, ceilings and garage walls.

Typically a retarding agent is added to the mix. this is normally Cream of Tartar (or "Dope" in the plasterer's jargon) and care must be taken with the amount added. Too much and the mix may never set at all. However the amount used is often estimated; much the way one adds a dash of salt to a recipe. you add a small scoop of retarder, dependent on the size of the mix. Retardant is added so that larger mixes can be made, since the texture technique doesn't require the person to wait until it starts to set before working it.

The lay-on phase is the same as smooth but it is added with a thicker coat. Once the coat is on uniformly the plasterer then goes back and birds his corners. Staying away from the corner he then gets a trowel with a nice banana curve in it and starts to run it over the wall in a figure eight or Ess pattern, making sure to cross all areas at least once. He adds a little extra plaster to his trowel if needed. The overall effect is layers of paint-like swaths over the whole of the ceiling or wall. He can then just walk away and let it set with care taken not too leave any globs and to make sure the corners look smooth and linear.

If a wall is to be smooth and the ceiling textured, typically the wall is done first, then the ceiling after the wall has set. Instead of rebirding the ceiling (which would have been done when the wall was laid on), a clean trowel is held against the wall and its corner is run along the ceiling to "cut it in" and clean the wall at the same time. This line is then smoothed with a paintbrush to make the transition seamless.

Sponge

The sponge (technically called a float), has a circle form and rough surface. it is fixed to a backing with a central handhold and is roughly the size of a standard trowel. Sponge is a variant texture technique and used normally on ceilings and sometimes in closets. Typically when using a sponge; sand is added to the mix and the technique is called sand-sponge.

Care must be taken not to stand directly under your trowel when doing this as it is very, very unpleasant, and dangerous to get a grain of sand in your eye; which is compounded by the irritation from the lime as well. This combination can easily scratch the eye.

The lay-on and mix is the same as with regular texturing. however after a uniform and smooth coat is placed on the ceiling and the edges are cut in; a special rectangular sponge with a handle is run across the ceiling in overlapping and circular motions. This takes some skill and practice to do well.

The overall look is a fishscale type pattern on the ceiling, closet wall, etc. Even though retarder is typically used; care must be taken to clean out the sponge thoroughly when finished as any plaster that hardens inside it will be impossible to remove.

Ceilings

Stilts are often required to plaster most ceilings and it is typically harder to lay-on and work than walls. For short ceilings one can also work with milk crates. The difficulty of working upside down often results in plaster bombs splattering on the floors, walls and people below.

This is why smooth ceilings, that use no retardant and sometimes even accelerant, are done before the walls. Retarded plaster can easily be scraped off a smooth plaster wall when wet. Any splatters from a smooth ceiling can easily be scraped off bare blueboard but not from an already plastered wall. Care must be taken when standing under your trowel or another plasterer.

The general difficulty of working a smooth ceiling fetches a higher cost. The technique is the same as a smooth wall but at an awkward angle for the plasterer.

Tools of the trade

  • Broom
  • Bucket trowel
  • Cornerbead
  • corner bird
  • Display bird-can be set for wider than 90 degree angles
  • Drywall Hammer or Drywall Hatchet -- use to clear plaster globs out of plugholes.
  • extension cords
  • 5 gallon buckets-for tools, washing, steps/stools, for small patch mixes, lugging plaster onto staging etc.
  • Floor scraper -- Optional
  • Gauging trowel
  • Halogen work lights
  • Hawk (plasterer's tool)
  • High RPM mixing drill with appropriate paddle
  • ladders and a few 6×4 planks-supplemental
  • masking tape -- for window panes and door jambs
  • mesh tape--multiple rolls
  • Milk crate -- used to store tools and as stools
  • Multi cord outlet
  • Pipe Staging-supplemental
  • Plastic 30 to 50 gallon drum-For mixing, often obtained from car washes
  • putty knife --supplemental
  • Scoop -supplemental-- to remove plaster from a bucket
  • Shovel -- short handled, is used to load the table with plaster mud.
  • soft bristle paintbrush -- for smoothing edges and corners
  • Trowels--various sizes and levels of breaking-in (cost avg $60)
  • Margin Trowel or margin for short—for edging the mix barrel
  • Spat or spatula trowel
  • sponge (tool)/Float
  • Staple gun -- for corner bead
  • table stand and a table board
  • tar paper or brown paper rolls—tar paper offers more water protection and is a bit more resilient but is costlier to use.
  • roll of plastic sheeting
  • Gypsum based plaster
  • DIAMOND Basecoat -- used in cases where cracking is suspected to occur, deep fill-ins
  • Utility knife--to cut plastic sheeting for table boards and floor covering paper
  • Water hose and nozzle
  • Water brush – large, for cleaning tools and splashing walls

Examples

In England, fine examples of plasterwork interiors of the early modern period can be seen at Chastleton House, (Oxfordshire), Knole House, (Kent), Wilderhope (Shropshire), Speke Hall, (Merseyside), and Haddon Hall, (Derbyshire).

Some examples of outstanding extant historical plasterwork interiors are found in Scotland, where the three finest specimens of interior plasterwork are elaborate decorated ceilings from the early 17th century at Muchalls Castle, Glamis Castle and Craigievar Castle, all of which are in the northeast region of that country.

The craft of modelled plasterwork, inspired by the style of the early modern period, was revived by the designers of the Arts and Crafts movement in late-19th- and early-20th-century England. Notable practitioners were Ernest Gimson, his pupil Norman Jewson, and George P. Bankart, who published extensively on the subject. Examples are preserved today at Owlpen Manor and Rodmarton Manor, both in the Cotswolds.

Modern ornate fibrous plasterwork by the specialist company of Clark & Fenn can be seen at Theatre Royal, Drury Lane, the London Palladium, Grand Theatre Leeds, Somerset House, The Plaisterers' Hall and St. Clement Danes

Corrado Parducci was a notable plaster worker in the Detroit area during the middle half of the 20th century. Probably his best known ceiling is located at Meadow Brook Hall.

See also

References

  1. J. Orsi, 2012, Degradation of hair in lime plasters, unpublished research
  2. SPAB 1990, Old Buildings need to Breathe. London

Public Domain This article incorporates text from a publication now in the public domain: Chisholm, Hugh, ed. (1911). "article name needed". Encyclopædia Britannica (11th ed.). Cambridge University Press. 

This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.