Molex connector

Molex Standard 0.093 inch pin and socket connectors

Molex connector is the vernacular term for a two-piece pin and socket interconnection, most frequently disk drive connectors. Pioneered by Molex Connector Company, the two-piece design became an early electronic standard. Molex developed and patented the first examples of this connector style in the late 1950s and early 1960s.[1][2] First used in home appliances, other industries soon began designing it into their products from automobiles to vending machines to mini-computers.

In such a connector, cylindrical spring-metal pins fit into cylindrical spring-metal sockets. The pins and sockets are held in a rectangular matrix in a nylon shell. The connector typically has two to 24 contacts and is polarized or keyed to ensure correct orientation. Pins and sockets can be arranged in any combination in a single housing, and each housing can be either male or female.

There are three typical pin sizes: 1.57 mm (0.062 in), 2.13 mm (0.084 in), and 2.36 mm (0.093 in). The 1.57 mm pin can carry 5 A of current, while the 2.36 mm can carry 8.5 A. Because the pins have a large contact surface area and fit tightly, these connectors are typically used for power.

In October 1963 AMP (now TE Connectivity) introduced the MATE-N-LOK connector.[3] The AMP connector was similar to the patented Molex connectors but not interchangeable. Both were widely used in the computer industry and the term "Molex Connector" is often improperly used to refer to all nylon plugs and receptacles.

The first 5.25 inch floppy disk drive, the Shugart SA400, introduced in August 1976 used the AMP MATE-N-LOK connector part number 350211-1.[4] This connector became the standard for 5.25 inch format peripherals such as hard drives and was used until introduction of SATA drives. In 1983, Molex introduced the 8981 connector that was fully compatible with the AMP MATE-N-LOK connector.[5]

AMP Mate-N-Lok and Molex Standard .093" Pin and Socket power connectors.

Desktop PC use

Several connector types have become established for connecting power in desktop PCs because of the simplicity, reliability, flexibility, and low cost of the Molex design. Certain Molex connectors are used for providing power to the motherboard, fans, floppy disk drive, CD/DVD drive, video card, some older hard drive models, and more. Compatible connectors are available from many manufacturers, not just Molex and AMP.

Motherboard

Motherboard power connector (Molex Mini-fit Jr. 39-28-1203,[6] former 5566-20A or 39-28-1243,[7] former 5566-24A)

ATX Connector

In 20/24 pin configurations, the Mini-Fit Jr. connector may be used on ATX motherboards as the main power connector. 4, 6 and 8 pin configurations of the same style of connector are used for additional CPU power and graphics card power. This is changing as power, signal and speed requirements increase in sophistication and electronic requirements. More commonly, the Mini-Fit, Jr. can be found in consumer applications, such as white goods, requiring high density and high current.

These connectors are polarized so that they usually cannot be inserted incorrectly, and lock into position using a latch.

Standard pinout:

24-pin ATX12V 2.x power supply connector
Color Signal[upper-alpha 1] Pin[upper-alpha 2] Pin[upper-alpha 2][upper-alpha 3] Signal[upper-alpha 1] Color
Orange +3.3 V 1 13 +3.3 V Orange
+3.3 V sense[upper-alpha 4] Brown
Orange +3.3 V 2 14 −12 V Blue
Black Ground 3 15 Ground Black
Red +5 V 4 16 Power on[upper-alpha 5] Green
Black Ground 5 17 Ground Black
Red +5 V 6 18 Ground Black
Black Ground 7 19 Ground Black
Grey Power good[upper-alpha 6] 8 20 Reserved[upper-alpha 7] None
Purple +5 V standby 9 21 +5 V Red
Yellow +12 V 10 22 +5 V Red
Yellow +12 V 11 23 +5 V Red
Orange +3.3 V 12 24 Ground Black
  1. 1 2      Light-blue background denotes control signals.
  2. 1 2      Light-green background denotes the pins present only in the 24-pin connector.
  3. ↑ In the 20-pin connector, pins 13–22 are numbered 11–20 respectively.
  4. ↑ Supplies +3.3 V power and also has a second low-current wire for remote sensing.[8]
  5. ↑ A control signal that is pulled up to +5 V by the PSU and must be driven low to turn on the PSU.
  6. ↑ A control signal that is low when other outputs have not yet reached, or are about to leave, correct voltages.
  7. ↑ Formerly −5 V (     white wire), absent in modern power supplies; it was optional in ATX and ATX12V v1.2 and deleted since v1.3.

Power good goes high to indicate that voltages are stabilised and ready for use. Power on is internally driven high, and shorting this pin to ground will turn on the power supply.

Disk drive

Disk drive connector (AMP MATE-N-LOK 1-480424-0 Power Connector)

AMP MATE-N-LOK Series

AMP MATE-N-LOK 1-480424-0 Power connector (female pins)
Type Electrical power connector
Production history
Manufacturer AMP
Produced 1963
General specifications
Width 21 mm (female), 23 mm (male)
Height 6 mm (female), 8 mm (male)
Pins 4
Electrical
Signal Yes
Max. voltage 12 V
Max. current 11 A/pin (30 °C rise)
Pin out
Male Pins (Female Connector)
Pin Color Type
Pin 1 Yellow +12 V
Pin 2 Black Ground
Pin 3 Black Ground
Pin 4 Red +5 V
18 AWG wire is typically used.

The desktop computer hard-drive connector is pictured here. It has four conductors, with the standard pinout as follows:

Pin #ColorFunction
1   Yellow +12 V
2   Black Ground
3   Black Ground
4   Red +5 V

Sometimes, especially in older computers, the colors differ. The pins are 0.200 in (5.08 mm) apart (center to center). The connector housing has chamfered corners on one side to prevent the user from plugging it in incorrectly. The connector that provides power (e.g., on a power supply) has female pins and a male housing; the connector that receives power (e.g., on a peripheral) has male pins and a female housing.

The connector is standard on all 5.25 inch floppy drives, 3.5 inch PATA and non-SCA SCSI disk drives; however, newer SATA disk drives employ a more advanced interconnection with 15 contacts. These advanced connection systems were first developed by Molex and other connector companies, often working together to develop interconnection standards. As SATA becomes more prevalent, Molex connectors can be found repurposed, through use of an adaptor, to serve as six-pin PCIe power connectors to make up for a lack of such connectors on a power supply.

Lower power devices (e. g. 3.5 inch floppy drives) use the smaller AMP 171822-4 connector instead.

Despite its widespread adoption, the connector does have problems. It is difficult to remove because it is held in place by friction instead of a latch, and some poorly constructed connectors may have one or more pins detach from the connector during mating or demating. There is also a tendency for the loosely inserted pins on the male connector to skew out of alignment. The female sockets can spread, making the connection imperfect and subject to arcing. Standard practice is to check for any sign of blackening or browning on the white plastic shell, which would indicate the need to replace the arcing connector. In extreme cases the whole connector can melt due to the heat from arcing.

See also

References

  1. ↑ Krehbiel, John H., "Wire Connector" US 3178673, issued April 1965
  2. ↑ Krehbiel, John H., "Electrical Connector Having Resilient Accurately Bendable Locking Means", US 3409858, issued November 1968
  3. ↑ United States Patent and Trademark Office, Word Mark MATE-N-LOK for Electrical Connectors first used in commerce Oct 18, 1963, Serial Number 72179683, Filing Date October 24, 1963, Registration Number 0786321, Registration Date March 9, 1965, Owner AMP INCORPORATED
  4. ↑ Shugart Associates (1977). SA400 minifloppy Diskette Storage Drive, OEM Manual (PDF). p. 18.
  5. ↑ "Power plug serves disk drives". Electronic Design. Hayden Publishing Company. 31 (22). October 27, 1983. A four-circuit power plug, the 8981 header, is intended primarily for computer disk drives.
  6. ↑ http://www.molex.com/molex/products/datasheet.jsp?part=active/0039281203_PCB_HEADERS.xml
  7. ↑ http://www.molex.com/molex/products/datasheet.jsp?part=active/0039281243_PCB_HEADERS.xml
  8. ↑ "ATX Specification Version 2.1" (PDF).
This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.