Mohr–Coulomb theory

Mohr–Coulomb theory is a mathematical model (see yield surface) describing the response of brittle materials such as concrete, or rubble piles, to shear stress as well as normal stress. Most of the classical engineering materials somehow follow this rule in at least a portion of their shear failure envelope. Generally the theory applies to materials for which the compressive strength far exceeds the tensile strength.[1]

In geotechnical engineering it is used to define shear strength of soils and rocks at different effective stresses.

In structural engineering it is used to determine failure load as well as the angle of fracture of a displacement fracture in concrete and similar materials. Coulomb's friction hypothesis is used to determine the combination of shear and normal stress that will cause a fracture of the material. Mohr's circle is used to determine which principal stresses that will produce this combination of shear and normal stress, and the angle of the plane in which this will occur. According to the principle of normality the stress introduced at failure will be perpendicular to the line describing the fracture condition.

It can be shown that a material failing according to Coulomb's friction hypothesis will show the displacement introduced at failure forming an angle to the line of fracture equal to the angle of friction. This makes the strength of the material determinable by comparing the external mechanical work introduced by the displacement and the external load with the internal mechanical work introduced by the strain and stress at the line of failure. By conservation of energy the sum of these must be zero and this will make it possible to calculate the failure load of the construction.

A common improvement of this model is to combine Coulomb's friction hypothesis with Rankine's principal stress hypothesis to describe a separation fracture.

History of the development

The Mohr–Coulomb theory is named in honour of Charles-Augustin de Coulomb and Christian Otto Mohr. Coulomb's contribution was a 1773 essay entitled "Essai sur une application des règles des maximis et minimis à quelques problèmes de statique relatifs à l'architecture" .[2] Mohr developed a generalised form of the theory around the end of the 19th century.[3] As the generalised form affected the interpretation of the criterion, but not the substance of it, some texts continue to refer to the criterion as simply the 'Coulomb criterion'.[4]

Mohr–Coulomb failure criterion

Figure 1: View of Mohr–Coulomb failure surface in 3D space of principal stresses for

The Mohr–Coulomb[5] failure criterion represents the linear envelope that is obtained from a plot of the shear strength of a material versus the applied normal stress. This relation is expressed as

where is the shear strength, is the normal stress, is the intercept of the failure envelope with the axis, and is the slope of the failure envelope. The quantity is often called the cohesion and the angle is called the angle of internal friction . Compression is assumed to be positive in the following discussion. If compression is assumed to be negative then should be replaced with .

If , the Mohr–Coulomb criterion reduces to the Tresca criterion. On the other hand, if the Mohr–Coulomb model is equivalent to the Rankine model. Higher values of are not allowed.

From Mohr's circle we have

where

and is the maximum principal stress and is the minimum principal stress.

Therefore, the Mohr–Coulomb criterion may also be expressed as

This form of the Mohr–Coulomb criterion is applicable to failure on a plane that is parallel to the direction.

Mohr–Coulomb failure criterion in three dimensions

The Mohr–Coulomb criterion in three dimensions is often expressed as

The Mohr–Coulomb failure surface is a cone with a hexagonal cross section in deviatoric stress space.

The expressions for and can be generalized to three dimensions by developing expressions for the normal stress and the resolved shear stress on a plane of arbitrary orientation with respect to the coordinate axes (basis vectors). If the unit normal to the plane of interest is

where are three orthonormal unit basis vectors, and if the principal stresses are aligned with the basis vectors , then the expressions for are

The Mohr–Coulomb failure criterion can then be evaluated using the usual expression

for the six planes of maximum shear stress.

Figure 2: Mohr–Coulomb yield surface in the -plane for
Figure 3: Trace of the Mohr–Coulomb yield surface in the -plane for

Mohr–Coulomb failure surface in Haigh–Westergaard space

The Mohr–Coulomb failure (yield) surface is often expressed in Haigh–Westergaad coordinates. For example, the function

can be expressed as

Alternatively, in terms of the invariants we can write

where

Mohr–Coulomb yield and plasticity

The Mohr–Coulomb yield surface is often used to model the plastic flow of geomaterials (and other cohesive-frictional materials). Many such materials show dilatational behavior under triaxial states of stress which the Mohr–Coulomb model does not include. Also, since the yield surface has corners, it may be inconvenient to use the original Mohr–Coulomb model to determine the direction of plastic flow (in the flow theory of plasticity).

A common approach is to use a non-associated plastic flow potential that is smooth. An example of such a potential is the function

where is a parameter, is the value of when the plastic strain is zero (also called the initial cohesion yield stress), is the angle made by the yield surface in the Rendulic plane at high values of (this angle is also called the dilation angle), and is an appropriate function that is also smooth in the deviatoric stress plane.

See also

References

  1. Juvinal, Robert C. & Marshek, Kurt .; Fundamentals of machine component design. – 2nd ed., 1991, pp. 217, ISBN 0-471-62281-8
  2. AMIR R. KHOEI; Computational Plasticity in Powder Forming Processes; Elsevier, Amsterdam; 2005; 449 pp.
  3. MAO-HONG YU; "Advances in strength theories for materials under complex stress state in the 20th Century"; Applied Mechanics Reviews; American Society of Mechanical Engineers, New York, U.S.A.; May 2002; 55 (3): pp. 169–218.
  4. NIELS SAABYE OTTOSEN and MATTI RISTINMAA; The Mechanics of Constitutive Modeling; Elsevier Science, Amsterdam, The Netherlands; 2005; pp. 165ff.
  5. Coulomb, C. A. (1776). Essai sur une application des regles des maximis et minimis a quelquels problemesde statique relatifs, a la architecture. Mem. Acad. Roy. Div. Sav., vol. 7, pp. 343–387.
This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.