DIMM

Two types of DIMMs: a 168-pin SDRAM module (top) and a 184-pin DDR SDRAM module (bottom). The SDRAM module has two notches (rectangular cuts or incisions) on the bottom edge, while the DDR1 SDRAM module has only one. Also, each module has eight RAM chips, but the lower one has an unoccupied space for the ninth chip.
Three SDRAM DIMM slots on a computer motherboard

A DIMM or dual in-line memory module comprises a series of dynamic random-access memory integrated circuits. These modules are mounted on a printed circuit board and designed for use in personal computers, workstations and servers. DIMMs began to replace SIMMs (single in-line memory modules) as the predominant type of memory module as Intel P5-based Pentium processors began to gain market share.

While the contacts on SIMMs on both sides are redundant, DIMMs have separate electrical contacts on each side of the module. Another difference is that standard SIMMs have a 32-bit data path, while standard DIMMs have a 64-bit data path. Since Intel's Pentium, many processors have a 64-bit bus width, requiring SIMMs installed in matched pairs in order to populate the data bus. The processor would then access the two SIMMs in parallel. DIMMs were introduced to eliminate this disadvantage.

Variants

Variants of DIMM slots support DDR, DDR2, DDR3 and DDR4 RAM.

Common types of DIMMs include the following:

70 to 200 pins

201 to 300 pins

168-pin SDRAM

Notch positions on DDR (top) and DDR2 (bottom) DIMM modules

On the bottom edge of 168-pin DIMMs there are two notches, and the location of each notch determines a particular feature of the module. The first notch is the DRAM key position, which represents RFU (reserved future use), registered, and unbuffered DIMM types (left, middle and right position, respectively). The second notch is the voltage key position, which represents 5.0 V, 3.3 V, and RFU DIMM types (order is the same as above).

DDR DIMMs

Two 8 GB DDR4-2133 ECC 1.2 V RDIMMs

DDR, DDR2, DDR3 and DDR4 all have different pin counts, and different notch positions. As of August, 2014, DDR4 SDRAM is a modern emerging type of dynamic random access memory (DRAM) with a high-bandwidth ("double data rate") interface, and has been in use since 2013. It is the higher-speed successor to DDR, DDR2 and DDR3. DDR4 SDRAM is neither forward nor backward compatible with any earlier type of random access memory (RAM) because of different signalling voltages, timings, as well as other differing factors between the technologies and their implementation.

SPD EEPROM

A DIMM's capacity and other operational parameters may be identified with serial presence detect (SPD), an additional chip which contains information about the module type and timing for the memory controller to be configured correctly. The SPD EEPROM connects to the System Management Bus and may also contain thermal sensors (TS-on-DIMM).[1]

Error correction

ECC DIMMs are those that have extra data bits which can be used by the system memory controller to detect and correct errors. There are numerous ECC schemes, but perhaps the most common is Single Error Correct, Double Error Detect (SECDED) which uses an extra byte per 64-bit word. ECC modules usually carry a multiple of 9 instead of a multiple of 8 chips.

Ranking

Sometimes memory modules are designed with two or more independent sets of DRAM chips connected to the same address and data buses; each such set is called a rank. Since all ranks share the same buses, only one rank may be accessed at any given time; it is specified by activating the corresponding rank's chip select (CS) signal. All other ranks are deactivated for the duration of the operation by having their corresponding CS signals deactivated. DIMMs are currently being commonly manufactured with up to four ranks per module. Consumer DIMM vendors have recently begun to distinguish between single and dual ranked DIMMs.

After a memory word is fetched, the memory is typically inaccessible for an extended period of time while the sense amplifiers are charged for access of the next cell. By interleaving the memory (e.g. cells 0, 4, 8, etc. are stored together in one rank), sequential memory accesses can be performed more rapidly because sense amplifiers have 3 cycles of idle time for recharging, between accesses.

DIMMs are often referred to as "single-sided" or "double-sided" to describe whether the DRAM chips are located on one or both sides of the module's printed circuit board (PCB). However, these terms may cause confusion, as the physical layout of the chips does not necessarily relate to how they are logically organized or accessed.

JEDEC decided that the terms "dual-sided", "double-sided", or "dual-banked" were not correct when applied to registered DIMMs (RDIMMs).

Organization

Most DIMMs are built using "×4" ("by four") or "×8" ("by eight") memory chips with nine chips per side; "×4" and "×8" refer to the data width of the DRAM chips in bits.

In the case of "×4" registered DIMMs, the data width per side is 36 bits; therefore, the memory controller (which requires 72 bits) needs to address both sides at the same time to read or write the data it needs. In this case, the two-sided module is single-ranked. For "×8" registered DIMMs, each side is 72 bits wide, so the memory controller only addresses one side at a time (the two-sided module is dual-ranked).

The above example applies to ECC memory that stores 72 bits instead of the more common 64. There would also be one extra chip per group of eight, which is not counted.

Speeds

For various technologies, there are certain bus and device clock frequencies that are standardized; there is also a decided nomenclature for each of these speeds for each type.

DIMMs based on Single Data Rate (SDR) DRAM have the same bus frequency for data, address and control lines. DIMMs based on Double Data Rate (DDR) DRAM have data but not the strobe at double the rate of the clock; this is achieved by clocking on both the rising and falling edge of the data strobes. Power consumption and voltage gradually became lower with each generation of DDR-based DIMMs.

SDR SDRAM DIMMs
Chip Module Effective Clock Voltage
SDR-66 PC-66 66 MHz 3.3 V
SDR-100 PC-100 100 MHz 3.3 V
SDR-133 PC-133 133 MHz 3.3 V
DDR SDRAM (DDR1) DIMMs
Chip Module Memory Clock I/O Bus Clock Transfer rate Voltage
DDR-200 PC-1600 100 MHz 100 MHz 200 MT/s 2.5 V
DDR-266 PC-2100 133 MHz 133 MHz 266 MT/s 2.5 V
DDR-333 PC-2700 166 MHz 166 MHz 333 MT/s 2.5 V
DDR-400 PC-3200 200 MHz 200 MHz 400 MT/s 2.5 V
DDR2 SDRAM DIMMs
Chip Module Memory Clock I/O Bus Clock Transfer rate Voltage
DDR2-400 PC2-3200 200 MHz 200 MHz 400 MT/s 1.8 V
DDR2-533 PC2-4200 266 MHz 266 MHz 533 MT/s 1.8 V
DDR2-667 PC2-5300 333 MHz 333 MHz 667 MT/s 1.8 V
DDR2-800 PC2-6400 400 MHz 400 MHz 800 MT/s 1.8 V
DDR2-1066 PC2-8500 533 MHz 533 MHz 1066 MT/s 1.8 V
DDR3 SDRAM DIMMs
Chip Module Memory Clock I/O Bus Clock Transfer rate Voltage
DDR3-800 PC3-6400 400 MHz 400 MHz 800 MT/s 1.5 V
DDR3-1066 PC3-8500 533 MHz 533 MHz 1066 MT/s 1.5 V
DDR3-1333 PC3-10600 667 MHz 667 MHz 1333 MT/s 1.5 V
DDR3-1600 PC3-12800 800 MHz 800 MHz 1600 MT/s 1.5 V
DDR3-1866 PC3-14900 933 MHz 933 MHz 1866 MT/s 1.5 V
DDR3-2133 PC3-17000 1066 MHz 1066 MHz 2133 MT/s 1.5 V
DDR3-2400 PC3-19200 1200 MHz 1200 MHz 2400 MT/s 1.5 V
DDR4 SDRAM DIMMs
Chip Module Memory Clock I/O Bus Clock Transfer rate Voltage
DDR4-1600 PC4-12800 800 MHz 800 MHz 1600 MT/s 1.2 V
DDR4-1866 PC4-14900 933 MHz 933 MHz 1866 MT/s 1.2 V
DDR4-2133 PC4-17000 1066 MHz 1066 MHz 2133 MT/s 1.2 V
DDR4-2400 PC4-19200 1200 MHz 1200 MHz 2400 MT/s 1.2 V
DDR4-2666 PC4-21300 1333 MHz 1333 MHz 2666 MT/s 1.2 V
DDR4-3200 PC4-25600 1600 MHz 1600 MHz 3200 MT/s 1.2 V

Form factors

Several form factors are commonly used in DIMMs. Single Data Rate Synchronous DRAM (SDR SDRAM) DIMMs were primarily manufactured in 1.5 inches (38 mm) and 1.7 inches (43 mm) heights. When 1U rackmount servers started becoming popular, these form factor registered DIMMs had to plug into angled DIMM sockets to fit in the 1.75 inches (44 mm) high box. To alleviate this issue, the next standards of DDR DIMMs were created with a "low profile" (LP) height of around 1.2 inches (30 mm). These fit into vertical DIMM sockets for a 1U platform.

With the advent of blade servers, angled slots have once again become common in order to accommodate LP form factor DIMMs in these space-constrained boxes. This led to the development of the Very Low Profile (VLP) form factor DIMM with a height of around 0.72 inches (18 mm). The DDR3 JEDEC standard for VLP DIMM height is around 0.740 inches (18.8 mm). These will fit vertically in ATCA systems.

Full-height 240-pin DDR2 and DDR3 DIMMs are all specified at a height of around 1.18 inches (30 mm) by standards set by JEDEC. These form factors include 240-pin DIMM, SODIMM, Mini-DIMM and Micro-DIMM.[2]

Full-height 288-pin DDR4 DIMMs are slightly taller than their DDR3 counterparts at 1.23 inches (31 mm). Similarly, VLP DDR4 DIMMs are also marginally taller than their DDR3 equivalent at nearly 0.74 inches (19 mm).[3]

As of Q2 2017 Asus has had a pci-e based "dimm.2" which has a similar socket to ddr3 dimms and is used to put in a module to connect up to two m.2 nvme ssds but it cannot use common ddr type ram and does not have much support other than Asus.

See also

References

  1. ↑ Temperature Sensor in DIMM memory modules
  2. ↑ JEDEC MO-269J Whitepaper., accessed Aug. 20, 2014.
  3. ↑ JEDEC MO-309E Whitepaper., accessed Aug. 20, 2014.
Wikimedia Commons has media related to DIMM.
This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.