6061 aluminium alloy

A6061
Physical Properties
Density (ρ) 2.70 g/cm3[1]
Mechanical Properties
Young's modulus (E) 68.9 GPa (9,990 ksi)
Tensile strengtht) 124–290 MPa (18.0–42.1 ksi)
Elongation (ε) at break 12–25%
Poisson's ratio (ν) 0.33
Thermal Properties
Melting temperature (Tm) 585 °C (1,085 °F)
Thermal conductivity (k) 151–202 W/(m·K)
Linear thermal expansion coefficient (α) 2.32×10−5 K−1
Specific heat capacity (c) 897 J/(kg·K)
Electrical Properties
Volume resistivity (ρ) 32.5–39.2 nOhm·m

6061 is a precipitation-hardened aluminium alloy, containing magnesium and silicon as its major alloying elements. Originally called "Alloy 61S", it was developed in 1935.[2] It has good mechanical properties, exhibits good weldability, and is very commonly extruded (second in popularity only to 6063).[3] It is one of the most common alloys of aluminium for general-purpose use.

It is commonly available in pre-tempered grades such as 6061-O (annealed), tempered grades such as 6061-T6 (solutionized and artificially aged) and 6061-T651 (solutionized, stress-relieved stretched and artificially aged).

Chemical composition

The alloy composition of 6061 is:

Mechanical properties

The mechanical properties of 6061 depend greatly on the temper, or heat treatment, of the material.[4] Young's Modulus is 69 GPa (10,000 ksi) regardless of temper.[5]

6061

Annealed 6061 (6061-O temper) has maximum tensile strength no more than 120 MPa (18,000 psi), and maximum yield strength no more than 55 MPa (8,000 psi). The material has elongation (stretch before ultimate failure) of 25–30%.

6061-T4

T4 temper 6061 has an ultimate tensile strength of at least 210 MPa (30,000 psi) and yield strength of at least 110 MPa (16,000 psi). It has elongation of 16%.

6061-T6

T6 temper 6061 has an ultimate tensile strength of at least 290 MPa (42,000 psi) and yield strength of at least 240 MPa (35,000 psi). More typical values are 310 MPa (45 ksi) and 270 MPa (39 ksi), respectively.[6] In thicknesses of 6.35 mm (0.250 in) or less, it has elongation of 8% or more; in thicker sections, it has elongation of 10%. T651 temper has similar mechanical properties. The typical value for thermal conductivity for 6061-T6 at 25 °C (77 °F) is around 152 W/m K. A material data sheet [7] defines the fatigue limit under cyclic load as 97 MPa (14,000 psi) for 500,000,000 completely reversed cycles using a standard RR Moore test machine and specimen. Note that aluminium does not exhibit a well defined "knee" on its S-n graph, so there is some debate as to how many cycles equates to "infinite life". Also note the actual value of fatigue limit for an application can be dramatically affected by the conventional de-rating factors of loading, gradient, and surface finish.

Uses

6061 is commonly used for the following:

6061-T6 is used for:

Welding

6061 is highly weldable, for example using tungsten inert gas welding (TIG) or metal inert gas welding (MIG). Typically, after welding, the properties near the weld are those of 6061-O, a loss of strength of around 80%. The material can be re-heat-treated to restore -T4 or -T6 temper for the whole piece. After welding, the material can naturally age and restore some of its strength as well. Nevertheless, the Alcoa Structural Handbook recommends the design strength of the material adjacent to the weld to be taken as 76 MPa (11,000 psi) without proper heat treatment after the weld. Typical filler material is 4043 or 5356(used only for non heat treatable aluminium such as 5052).

Extrusions

6061 is an alloy used in the production of extrusions—long constant–cross-section structural shapes produced by pushing metal through a shaped die.

Forgings

6061 is an alloy that is suitable for hot forging. The billet is heated through an induction furnace and forged using a closed die process. This particular alloy is suitable for open die forgings. Automotive parts, ATV parts, and industrial parts are just some of the uses as a forging. Aluminium 6061 can be forged into flat or round bars, rings, blocks, discs and blanks, hollows, and spindles. 6061 can be forged into special and custom shapes.[13]

Standards

Different forms and tempers of 6061 aluminum alloy are discussed in the following standards:[14]

References

  1. ASM Handbook, Volume 2: Properties and Selection: Nonferrous Alloys and Special-Purpose Materials ASM Handbook Committee, p 102 DOI: 10.1361/asmhba0001060.
  2. Robert E. Sanders, Jr. (2001). "Technology Innovation in Aluminum Products". JOM. 53 (2): 21–25. Bibcode:2001JOM....53b..21S. doi:10.1007/s11837-001-0115-7.
  3. "Aluminum Alloys". Materials Management Inc. 23 December 2015. Retrieved 2016-07-25.
  4. Alcoa 6061 data sheet Archived 2006-10-20 at the Wayback Machine. (pdf), accessed October 13, 2006
  5. Aluminum Standards and Data 2006 Metric SI, by the Aluminum Association Inc.
  6. Material Properties Data: 6061-T6 Aluminium
  7. ASM Material Data Sheet
  8. Aluminum Information at aircraftspruce.com, accessed October 13, 2006
  9. 6061 vs 2024. Homebuiltairplanes.com. Retrieved on 2012-04-04.
  10. Boatbuilding with Aluminum, Stephen F. Pollard, 1993, ISBN 0-07-050426-1
  11. EVOLUTION 9mm™, 1/2-28 TPI. Advanced Armament. Retrieved on 2012-04-04.
  12. Amphibian S .22LR : Suppressor : AWC Systems Technology. Awcsystech.com. Retrieved on 2012-04-04.
  13. "6061 Aluminum Alloy Forging | Anderson Shumaker". www.andersonshumaker.com. Retrieved 2015-10-08.
  14. 6061 (3.3214, H20, A96061) Aluminum. Retrieved on 2014-11-14.

Further reading

This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.