Quadrature amplitude modulation

Passband modulation
Analog modulation
AM FM PM QAM SM SSB
Digital modulation
ASK APSK CPM FSK MFSK MSK OOK PPM PSK QAM SC-FDE TCM WDM
Hierarchical modulation
QAM WDM
Spread spectrum
CSS DSSS FHSS THSS
See also
Capacity-approaching codes Demodulation Line coding Modem AnM PoM PAM PCM PWM ΔΣM OFDM FDM Multiplexing

Quadrature amplitude modulation (QAM) is both an analog and a digital modulation scheme. It conveys two analog message signals, or two digital bit streams, by changing (modulating) the amplitudes of two carrier waves, using the amplitude-shift keying (ASK) digital modulation scheme or amplitude modulation (AM) analog modulation scheme. The two carrier waves of the same frequency, usually sinusoids, are out of phase with each other by 90° and are thus called quadrature carriers or quadrature components — hence the name of the scheme. The modulated waves are summed, and the final waveform is a combination of both phase-shift keying (PSK) and amplitude-shift keying (ASK), or, in the analog case, of phase modulation (PM) and amplitude modulation. In the digital QAM case, a finite number of at least two phases and at least two amplitudes are used. PSK modulators are often designed using the QAM principle, but are not considered as QAM since the amplitude of the modulated carrier signal is constant. QAM is used extensively as a modulation scheme for digital telecommunication systems. Arbitrarily high spectral efficiencies can be achieved with QAM by setting a suitable constellation size, limited only by the noise level and linearity of the communications channel.^[1]

QAM is being used in optical fiber systems as bit rates increase; QAM16 and QAM64 can be optically emulated with a 3-path interferometer.^[2]^[3]

Introduction

Like all modulation schemes, QAM conveys data by changing some aspect of a carrier signal, or the carrier wave, (usually a sinusoid) in response to a data signal. In the case of QAM, the amplitude of two waves of the same frequency, 90° out-of-phase with each other (in quadrature) are changed (modulated or keyed) to represent the data signal. Amplitude modulating two carriers in quadrature can be equivalently viewed as both amplitude modulating and phase modulating a single carrier.

Phase modulation (analog PM) and phase-shift keying (digital PSK) can be regarded as a special case of QAM, where the magnitude of the modulating signal is a constant, with only the phase varying. This can also be extended to frequency modulation (FM) and frequency-shift keying (FSK), for these can be regarded as a special case of phase modulation.

Analog QAM

Analog QAM: measured PAL colour bar signal on a vector analyser screen.

When transmitting two signals by modulating them with QAM, the transmitted signal will be of the form:

{\begin{aligned}s(t)&=Re\left\{\left[I(t)+iQ(t)\right]e^{i2\pi f_{0}t}\right\}\\&=I(t)\cos(2\pi f_{0}t)-Q(t)\sin(2\pi f_{0}t)\end{aligned}}

where $\scriptstyle i^{2}\;=\;-1$ , $\scriptstyle I(t)$ and $\scriptstyle Q(t)$ are the modulating signals, $\scriptstyle f_0$ is the carrier frequency and $Re\{\}$ is the real part.

At the receiver, these two modulating signals can be demodulated using a coherent demodulator. Such a receiver multiplies the received signal separately with both a cosine and sine signal to produce the received estimates of $\scriptstyle I(t)$ and $\scriptstyle Q(t)$ respectively. Because of the orthogonality property of the carrier signals, it is possible to detect the modulating signals independently.

In the ideal case $\scriptstyle I(t)$ is demodulated by multiplying the transmitted signal with a cosine signal:

\begin{align} r(t) &= s(t) \cos (2 \pi f_0 t) \\ &= I(t) \cos (2 \pi f_0 t)\cos (2 \pi f_0 t) - Q(t) \sin (2 \pi f_0 t)\cos (2 \pi f_0 t) \end{align}

Using standard trigonometric identities, we can write it as:

\begin{align} r(t) &= \frac{1}{2} I(t) \left[1 + \cos (4 \pi f_0 t)\right] - \frac{1}{2} Q(t) \sin (4 \pi f_0 t) \\ &= \frac{1}{2} I(t) + \frac{1}{2} [I(t) \cos (4 \pi f_0 t) - Q(t) \sin (4 \pi f_0 t)] \end{align}

Low-pass filtering $\scriptstyle r(t)$ removes the high frequency terms (containing $\scriptstyle 4\pi f_0 t$ ), leaving only the $\scriptstyle I(t)$ term. This filtered signal is unaffected by $\scriptstyle Q(t)$ , showing that the in-phase component can be received independently of the quadrature component. Similarly, we may multiply $\scriptstyle s(t)$ by a sine wave and then low-pass filter to extract $\scriptstyle Q(t)$ .

Analog QAM suffers from the same problem as Single-sideband modulation: the exact phase of the carrier is required for correct demodulation at the receiver. If the demodulating phase is even a little off, it results in crosstalk between the modulated signals. This issue of carrier synchronization at the receiver must be handled somehow in QAM systems. The coherent demodulator needs to be exactly in phase with the received signal, or otherwise the modulated signals cannot be independently received. This is achieved typically by transmitting a burst subcarrier or a Pilot signal.

Analog QAM is used in:

NTSC and PAL analog Color television systems, where the I- and Q-signals carry the components of chroma (colour) information. The QAM carrier phase is recovered from a special Colorburst transmitted at the beginning of each scan line.
C-QUAM ("Compatible QAM") is used in AM stereo radio to carry the stereo difference information.

Fourier analysis of QAM

In the frequency domain, QAM has a similar spectral pattern to DSB-SC modulation. Using the properties of the Fourier transform, we find that:

S(f) = \frac{1}{2}\left[ M_I(f - f_0) + M_I(f + f_0) \right] + \frac{i}{2}\left[ M_Q(f - f_0) - M_Q(f + f_0) \right]

where S(f), M_I(f) and M_Q(f) are the Fourier transforms (frequency-domain representations) of s(t), I(t) and Q(t), respectively.

Quantized QAM

Digital 16-QAM with example constellation points

As in many digital modulation schemes, the constellation diagram is useful for QAM. In QAM, the constellation points are usually arranged in a square grid with equal vertical and horizontal spacing, although other configurations are possible (e.g. Cross-QAM). Since in digital telecommunications the data is usually binary, the number of points in the grid is usually a power of 2 (2, 4, 8, …). Since QAM is usually square, some of these are rare—the most common forms are 16-QAM, 64-QAM and 256-QAM. By moving to a higher-order constellation, it is possible to transmit more bits per symbol. However, if the mean energy of the constellation is to remain the same (by way of making a fair comparison), the points must be closer together and are thus more susceptible to noise and other corruption; this results in a higher bit error rate and so higher-order QAM can deliver more data less reliably than lower-order QAM, for constant mean constellation energy. Using higher-order QAM without increasing the bit error rate requires a higher signal-to-noise ratio (SNR) by increasing signal energy, reducing noise, or both.

If data-rates beyond those offered by 8-PSK are required, it is more usual to move to QAM since it achieves a greater distance between adjacent points in the I-Q plane by distributing the points more evenly. The complicating factor is that the points are no longer all the same amplitude and so the demodulator must now correctly detect both phase and amplitude, rather than just phase.

64-QAM and 256-QAM are often used in digital cable television and cable modem applications. In the United States, 64-QAM and 256-QAM are the mandated modulation schemes for digital cable (see QAM tuner) as standardised by the SCTE in the standard ANSI/SCTE 07 2013. Note that many marketing people will refer to these as QAM-64 and QAM-256. In the UK, 64-QAM is used for digital terrestrial television (Freeview) whilst 256-QAM is used for Freeview-HD.

Bit-loading (bits per QAM constellation) on an ADSL line

Communication systems designed to achieve very high levels of spectral efficiency usually employ very dense QAM constellations. For example, current Homeplug AV2 500-Mbit powerline Ethernet devices use 1024-QAM and 4096-QAM,^[4] as well as future devices using ITU-T G.hn standard for networking over existing home wiring (coaxial cable, phone lines and power lines); 4096-QAM provides 12 bits/symbol. Another example is ADSL technology for copper twisted pairs, whose constellation size goes up to 32768-QAM (in ADSL terminology this is referred to as bit-loading, or bit per tone, 32768-QAM being equivalent to 15 bits per tone).^[5]

Ultra-high capacity Microwave Backhaul Systems also use 1024-QAM.^[6] With 1024-QAM, Adaptive Coding and Modulation (ACM), and XPIC, Vendors can obtain Gigabit capacity in a single 56 MHz channel.^[7]

Ideal structure

Transmitter

The following picture shows the ideal structure of a QAM transmitter, with a carrier center frequency $\scriptstyle f_0$ and the frequency response of the transmitter's filter $\scriptstyle H_t$ :

First the flow of bits to be transmitted is split into two equal parts: this process generates two independent signals to be transmitted. They are encoded separately just like they were in an amplitude-shift keying (ASK) modulator. Then one channel (the one "in phase") is multiplied by a cosine, while the other channel (in "quadrature") is multiplied by a sine. This way there is a phase of 90° between them. They are simply added one to the other and sent through the real channel.

The sent signal can be expressed in the form:

s(t) = \sum_{n=-\infty}^{\infty} \left[ v_c [n] \cdot h_t (t - n T_s) \cos (2 \pi f_0 t) - v_s[n] \cdot h_t (t - n T_s) \sin (2 \pi f_0 t) \right]

where $\scriptstyle v_c[n]$ and $\scriptstyle v_s[n]$ are the voltages applied in response to the $\scriptstyle n$ ^th symbol to the cosine and sine waves respectively.

Receiver

The receiver simply performs the inverse operation of the transmitter. Its ideal structure is shown in the picture below with $\scriptstyle H_r$ the receive filter's frequency response :

Multiplying by a cosine (or a sine) and by a low-pass filter it is possible to extract the component in phase (or in quadrature). Then there is only an ASK demodulator and the two flows of data are merged back.

In practice, there is an unknown phase delay between the transmitter and receiver that must be compensated by synchronization of the receiver's local oscillator (i.e. the sine and cosine functions in the above figure). In mobile applications, there will often be an offset in the relative frequency as well, due to the possible presence of a Doppler shift proportional to the relative velocity of the transmitter and receiver. Both the phase and frequency variations introduced by the channel must be compensated by properly tuning the sine and cosine components, which requires a phase reference, and is typically accomplished using a Phase-Locked Loop (PLL).

In any application, the low-pass filter and the receive $\scriptstyle H_r$ filter will be implemented as a single combined filter. Here they are shown as separate just to be clearer.

Quantized QAM performance

The following definitions are needed in determining error rates:

$\scriptstyle M$ = Number of symbols in modulation constellation
$\scriptstyle E_b$ = Energy-per-bit
$\scriptstyle E_s$ = Energy-per-symbol = $\scriptstyle kE_b$ with k bits per symbol
$\scriptstyle N_0$ = Noise power spectral density (W/Hz)
$\scriptstyle P_b$ = Probability of bit-error
$\scriptstyle P_{bc}$ = Probability of bit-error per carrier
$\scriptstyle P_s$ = Probability of symbol-error
$\scriptstyle P_{sc}$ = Probability of symbol-error per carrier
$\scriptstyle Q(x) \;=\; \frac{1}{\sqrt{2\pi}}\int_{x}^{\infty}e^{-\frac{1}{2}t^{2}}dt,\ x \geq 0$

$\scriptstyle Q(x)$ is related to the complementary Gaussian error function by: $\scriptstyle Q(x) \;=\; \frac{1}{2}\operatorname{erfc}\left(\frac{1}{\sqrt{2}}x\right)$ , which is the probability that x will be under the tail of the Gaussian PDF towards positive infinity.

The error rates quoted here are those in additive white Gaussian noise (AWGN).

Where coordinates for constellation points are given in this article, note that they represent a non-normalised constellation. That is, if a particular mean average energy were required (e.g. unit average energy), the constellation would need to be linearly scaled.

Rectangular QAM

Constellation diagram for rectangular 16-QAM.

Rectangular QAM constellations are, in general, sub-optimal in the sense that they do not maximally space the constellation points for a given energy. However, they have the considerable advantage that they may be easily transmitted as two pulse amplitude modulation (PAM) signals on quadrature carriers, and can be easily demodulated. The non-square constellations, dealt with below, achieve marginally better bit-error rate (BER) but are harder to modulate and demodulate.

The first rectangular QAM constellation usually encountered is 16-QAM, the constellation diagram for which is shown here. A Gray coded bit-assignment is also given. The reason that 16-QAM is usually the first is that a brief consideration reveals that 2-QAM and 4-QAM are in fact binary phase-shift keying (BPSK) and quadrature phase-shift keying (QPSK), respectively. Also, the error-rate performance of 8-QAM is close to that of 16-QAM (only about 0.5 dB better), but its data rate is only three-quarters that of 16-QAM.

Expressions for the symbol-error rate of rectangular QAM are not hard to derive but yield rather unpleasant expressions. For M-ary square QAM exact expressions are available. They are most easily expressed in a per carrier sense:

P_{sc} = 2\left(1 - \frac{1}{\sqrt M}\right)Q\left(\sqrt{\frac{3}{M-1}\frac{E_s}{N_0}}\right)

\,P_s = 1 - \left(1 - P_{sc}\right)^2

The bit-error rate depends on the bit to symbol mapping, but for $\scriptstyle E_b/N_0 \gg 1$ and a Gray-coded assignment—so that we can assume each symbol error causes only one bit error—the bit-error rate is approximately

P_{bc} \approx \frac{P_{sc}}{\frac{1}{2}k} = \frac{4}{k}\left(1 - \frac{1}{\sqrt M}\right)Q\left(\sqrt{\frac{3k}{M-1}\frac{E_b}{N_0}}\right)

Since the carriers are independent, the overall bit error rate is the same as the per-carrier error rate, just like BPSK and QPSK:

\,P_b = P_{bc}

The exact and general closed-form expression of the bit error rate for rectangular QAM of size $M=I\times J$ , where $I,J$ is the size of the in-phase/quadrature PAM forming the QAM, respectively, was derived analytically for the AWGN channel:^[8]

P_{b}={\frac {1}{\log _{2}\left(I\cdot J\right)}}\left(\sum _{i=1}^{\log _{2}I}P_{I}(i)+\sum _{l=1}^{\log _{2}J}P_{J}(l)\right)

where

P_{P}(l)={\frac {2}{P}}\sum _{k=0}^{(1-2^{-l})P-1}\left(-1\right)^{\left\lfloor {\frac {k\cdot 2^{l-1}}{P}}\right\rfloor }\cdot \left(2^{l-1}-\left\lfloor {\frac {k\cdot 2^{l-1}}{P}}+{\frac {1}{2}}\right\rfloor \right)\cdot Q\left(\left(2k+1\right){\sqrt {{\frac {6\log _{2}(I\cdot J)}{I^{2}+J^{2}-2}}{\frac {E_{b}}{N_{0}}}}}\right)

with $P\in \{I,J\}$ . M-ary square QAM is a special case with $I=J={\sqrt {M}}$ .

Odd-k QAM

For odd $\scriptstyle k$ , such as 8-QAM ( $\scriptstyle k \;=\; 3$ ) it is harder to obtain symbol-error rates, but a tight upper bound is:

P_s \leq{} 4Q\left(\sqrt{\frac{3kE_b}{(M - 1)N_0}}\;\right)

Two rectangular 8-QAM constellations are shown below without bit assignments. These both have the same minimum distance between symbol points, and thus the same symbol-error rate (to a first approximation).

The exact bit-error rate, $\scriptstyle P_b$ will depend on the bit-assignment.

Note that both of these constellations are seldom used in practice, as the non-rectangular version of 8-QAM is optimal.

Constellation diagram for rectangular 8-QAM.
Alternative constellation diagram for rectangular 8-QAM.

Non-rectangular QAM

Constellation diagram for circular 8-QAM.

Constellation diagram for circular 16-QAM.

It is the nature of QAM that most orders of constellations can be constructed in many different ways and it is neither possible nor instructive to cover them all here. This article instead presents two, lower-order constellations.

Two diagrams of circular QAM constellation are shown, for 8-QAM and 16-QAM. The circular 8-QAM constellation is known to be the optimal 8-QAM constellation in the sense of requiring the least mean power for a given minimum Euclidean distance. The 16-QAM constellation is suboptimal although the optimal one may be constructed along the same lines as the 8-QAM constellation. The circular constellation highlights the relationship between QAM and PSK. Other orders of constellation may be constructed along similar (or very different) lines. It is consequently hard to establish expressions for the error rates of non-rectangular QAM since it necessarily depends on the constellation. Nevertheless, an obvious upper bound to the rate is related to the minimum Euclidean distance of the constellation (the shortest straight-line distance between two points):

P_s < (M-1)Q\left(\sqrt{\frac{d_{min}^{2}}{2N_0}}\right)

Again, the bit-error rate will depend on the assignment of bits to symbols.

Although, in general, there is a non-rectangular constellation that is optimal for a particular $\scriptstyle M$ , they are not often used since the rectangular QAMs are much easier to modulate and demodulate.

Hierarchical QAM

Hierarchical QAM is a form of hierarchical modulation. For example, hierarchical QAM is used in DVB, where the constellation points are grouped into a high-priority QPSK stream and a low-priority 16-QAM stream. The irregular distribution of constellation points improves the reception probability of the high-priority stream in low SNR conditions, at the expense of higher SNR requirements for the low-priority stream.^[9]

Mutual Information with AWGN

Mutual Information of QAM over the AWGN channel. Notes: 4-QAM is QPSK. 8-QAM means circular 8-QAM.

The mutual information of QAM can be evaluated in additive Gaussian noise by numerical integration of its definition.^[10] The curves of mutual information saturate to the number of bits carried by each symbol in the limit of infinite signal to noise ratio $E_{s}/N_{0}$ . On the contrary, in the limit of small signal to noise ratios the mutual information approaches the AWGN channel capacity, which is the supremum among all possible choices of symbol statistical distributions.

The mutual information of QAM is generally closer to the AWGN channel capacity than PSK modulation formats.

Interference and noise

In moving to a higher order QAM constellation (higher data rate and mode) in hostile RF/microwave QAM application environments, such as in broadcasting or telecommunications, multipath interference typically increases. There is a spreading of the spots in the constellation, decreasing the separation between adjacent states, making it difficult for the receiver to decode the signal appropriately. In other words, there is reduced noise immunity. There are several test parameter measurements which help determine an optimal QAM mode for a specific operating environment. The following three are most significant:^[11]

Carrier/interference ratio
Carrier-to-noise ratio
Threshold-to-noise ratio

References

↑ "Digital Modulation Efficiencies". Barnard Microsystems. Archived from the original on 2011-04-30.
↑ "Ciena tests 200G via 16-QAM with Japan-U.S. Cable Network". lightwave. April 17, 2014. Retrieved 7 November 2016.
↑ Kylia products Archived July 13, 2011, at the Wayback Machine., dwdm mux demux, 90 degree optical hybrid, d(q) psk demodulatorssingle polarization
↑ http://www.homeplug.org/media/filer_public/a1/46/a1464318-f5df-46c5-89dc-7243d8ccfcee/homeplug_av2_whitepaper_150907.pdf Homeplug_AV2 whitepaper
↑ http://www.itu.int/rec/T-REC-G.992.3-200904-I section 8.6.3 Constellation mapper - maximum number of bits per constellation BIMAX ≤ 15
↑ http://www.trangosys.com/products/point-to-point-wireless-backhaul/licensed-wireless/trangolink-apex-orion.shtml A Apex Orion
↑ http://www.trangosys.com/products/point-to-point-wireless-backhaul/licensed-wireless/trangolink-apex-orion.shtml A Apex Orion
↑ Cho, Kyongkuk; Yoon, Dongweon (July 2002). "On the General BER Expression of One- and Two-Dimensional Amplitude Modulations". IEEE Trans. Commun. 50 (7): 1074–1080. doi:10.1109/TCOMM.2002.800818.
↑ http://asp.eurasipjournals.com/content/2010/1/942638 DVB Hierarchical QAM constellation
↑ Blahut, R. E. (1988). Principles and Practice of Information Theory. Boston, MA, USA: Addison Wesley Publishing Company. ISBN 0-201-10709-0.
↑ Howard Friedenberg and Sunil Naik. "Hitless Space Diversity STL Enables IP+Audio in Narrow STL Bands" (PDF). 2005 National Association of Broadcasters Annual Convention. Retrieved April 17, 2005.

5. Jonqyin (Russell) Sun "Linear diversity analysis for QAM in Rician fading channels", IEEE WOCC 2014

The notation used here has mainly (but not exclusively) been taken from

John G. Proakis, "Digital Communications, 3rd Edition",

External links

Wikimedia Commons has media related to Quadrature amplitude modulation.

Interactive webdemo of QAM constellation with additive noise Institute of Telecommunicatons, University of Stuttgart
QAM bit error rate for AWGN channel – online experiment
How imperfections affect QAM constellation
Microwave Phase Shifters Overview by Herley General Microwave
Simulation of dual-polarization QPSK (DP-QPSK) for 100G optical transmission

Analog television broadcasting topics
Systems	180-line 405-line ( System A ) 441-line 525-line ( System J , System M ) 625-line ( System B , System C , System D , System G , System H , System I , System K , System L , System N ) 819-line ( System E , System F )
Color systems	NTSC PAL PAL-M PAL-S PALplus SECAM
Video	Back porch and front porch Black level Blanking level Chrominance Chrominance subcarrier Colorburst Color killer Color TV Composite video Frame (video) Horizontal scan rate Horizontal blanking interval Luma Nominal analogue blanking Overscan Raster scan Safe area Television lines Vertical blanking interval White clipper
Sound	Multichannel television sound NICAM Sound-in-Syncs Zweikanalton
Modulation	Frequency modulation Quadrature amplitude modulation Vestigial sideband modulation (VSB)
Transmission	Amplifiers Antenna (radio) Broadcast transmitter/Transmitter station Cavity amplifier Differential gain Differential phase Diplexer Dipole antenna Dummy load Frequency mixer Intercarrier method Intermediate frequency Output power of an analog TV transmitter Pre-emphasis Residual carrier Split sound system Superheterodyne transmitter Television receive-only Direct-broadcast satellite television Television transmitter Terrestrial television Transposer
Frequencies & Bands	Frequency offset Microwave transmission Television channel frequencies UHF VHF
Propagation	Beam tilt Distortion Earth bulge Field strength in free space Knife-edge effect Noise (electronics) Null fill Path loss Radiation pattern Skew Television interference
Testing	Distortionmeter Field strength meter Vectorscope VIT signals Zero reference pulse
Artifacts	Dot crawl Ghosting Hanover bars Sparklies

Telecommunications
History	Beacon Broadcasting Cable protection system Cable TV Communications satellite Computer network Drums Electrical telegraph Fax Heliographs Hydraulic telegraph Internet Mass media Mobile phone Optical telecommunication Optical telegraphy Pager Photophone Prepaid mobile phone Radio Radiotelephone Satellite communications Semaphore Smartphone Smoke signals Telecommunications history Telautograph Telegraphy Teleprinter (teletype) Telephone The Telephone Cases Television Timeline of communication technology Undersea telegraph line Videoconferencing Videophone Videotelephony Whistled language
Pioneers	Edwin Howard Armstrong John Logie Baird Paul Baran Alexander Graham Bell Tim Berners-Lee Jagadish Chandra Bose Vint Cerf Claude Chappe Donald Davies Lee de Forest Philo Farnsworth Reginald Fessenden Elisha Gray Erna Schneider Hoover Charles K. Kao Hedy Lamarr Innocenzo Manzetti Guglielmo Marconi Antonio Meucci Radia Perlman Alexander Stepanovich Popov Johann Philipp Reis Nikola Tesla Camille Tissot Alfred Vail Charles Wheatstone Vladimir K. Zworykin
Transmission media	Characteristic impedance Coaxial cable Electromagnetic radiation Electrical cable Free-space optical communication Heaviside condition Loading coil Molecular communication Optical fiber Telegrapher's equations
Network topology and switching	Links Nodes Terminal node Network switching (circuit packet) Telephone exchange
Multiplexing	Space-division Frequency-division Time-division Polarization-division Orbital angular-momentum Code-division
Networks	ARPANET BITNET Cellular network Computer CYCLADES Ethernet FidoNet Internet ISDN LAN Mobile NGN NPL network Public Switched Telephone Radio Telecommunications equipment Television Telex WAN Wireless World Wide Web
Category Portal

This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.