Theory of sonics

The theory of sonics is a branch of continuum mechanics which describes the transmission of mechanical energy through vibrations. The birth of the theory of sonics[1] can be considered the publication of the book A treatise on transmission of power by vibrations in 1918 by the Romanian scientist Gogu Constantinescu.

ONE of the fundamental problems of mechanical engineering is that of transmitting energy found in nature, after suitable transformation, to some point at which can be made available for performing useful work. The methods of transmitting power known and practised by engineers are broadly included in two classes: mechanical including hydraulic, pneumatic and wire rope methods; and electrical methods....According to the new system, energy is transmitted from one point to another, which may be at a considerable distance, by means of impressed variations of pressure or tension producing longitudinal vibrations in solid, liquid or gaseous columns. The energy is transmitted by periodic changes of pressure and volume in the longitudinal direction and may be described as wave transmission of power, or mechanical wave transmission. Gogu Constantinescu[2][3]

Later on the theory was expanded in electro-sonic, hydro-sonic, sonostereo-sonic and thermo-sonic. The theory was the first chapter of compressible flow applications and has stated for the first time the mathematical theory of compressible fluid, and was considered a branch of continuum mechanics.The laws discovered by Constantinescu, used in sonicity are the same with the laws used in electricity.

Book chapters

The book A treatise on transmission of power by vibrations has the following chapters:

  1. Introductory
  2. Elementary physical principles
  3. Definitions
  4. Effects of capacity, inertia, friction, and leakage on alternating currents
  5. Waves in long pipes
  6. Alternating in long pipes allowing for Friction
  7. Theory of displacements motors
  8. Theory of resonators
  9. High-frequency currents
  10. Charged lines
  11. Transformers

George Constantinescu defined his work as follow.

Theory of sonics: applications

No. 55 squadron of DH4s, the first aircraft to go into active service fitted with the C.C. Gear, arrived in France on 6 March 1917.

Elementary physical principles

If v is the velocity of which waves travel along the pipe, and n the number of the revolutions of the crank a
The wavelength λ is =v/n
Assuming that the pipe is finite and closed at the point r situated at a distance which is multiple of λ, and considering that the piston is smaller than wavelength, at r the wave compression is stopped and reflected, the reflected wave traveling back along the pipe.

Physics
Elementary physical principles Description
Figure I

Suppose the crank a to be rotating uniformly, causing the piston b to reciprocate in the pipe c, which is full of liquid. At each in stroke of the piston a zone of high pressure is formed, and these zones, shown by shading, travel along the pipe away from the piston; between every pair of high pressures zones is a zone of light pressure shown in the picture. The pressure at any point in the pipe will go through a series of values from a maximum to a minimum.

Figure II

Assuming that the pipe is finite and closed at the point r situated at a distance which is multiple of λ, and considering that the piston is smaller than the wavelength, at r the wave compression is stopped and reflected, the reflected wave traveling back along the pipe.If the crank continues rotation at uniform speed, a zone of maximum pressure will start from the piston at the same time the reflected wave cme to the piston, as a result the maximum pressure will double. At next rotation the amplitude is increased, and so on, till the pipe burst.

Figure III

If instead of a closing pipe we have a piston at r;the wave will be similar at piston b and piston m,the piston m therefore will have the same energy as the piston b; if the distance between the b and m is not a multiple of λ the movement of m will differ in phase compared with the piston b.

Figure IV

If more energy is produced by piston b then is taken by piston m the energy will be reflected by piston m in pipe, and the energy will accumulate till the pipe burst.If we have a large volume vessel d, compared with the stroke volume of piston b, the capacity d will act as a spring taking out the energy of direct or reflected waves at high pressure, and giving back energy when pressure falls. The mean pressure in d and in the pipe will be the same. The result of reflected waves will be a stationary wave in pipe with no increase of energy, and the pressure in the pipe will never exceed the pressure limit.

Figure V

Waves are transmitted by a reciprocating piston along the pipe eeee. The pipe is closed at p, a distance of one complete wavelength. There are branches at one-half, three-quarters and one full wavelength distances. If p is open and d is open, the motor l will rotate synchronous with motor a. If all valves are closed, there will be a stationary wave with extreme values at λ and λ/2, (points b and d,) where the flow will be zero, and where the pressure will alternate between maximum and minimum values determined by the capacity of reservoir f. The maximum and minimum points do not move along the pipe, and no energy flows from generator a. If valve b is open, the motor m is able to take the energy from the line, the stationary half-wave between a and b being replaced by a traveling wave; between b and p a stationary wave will persist. If only valve c is open, since at this point the variation of pressure is always zero, no energy can be taken out by the motor n, and the stationary wave will persist. If the motor is connected in an intermediary point, part of the energy will be taken out by the motor while the stationary wave will persist at reduced amplitude. If the motor l is not capable of consuming all the energy of the generator a, then there will be a traveling wave a and a stationary wave. Therefore, there will be no point in the pipe where the pressure variation will be zero, and consequently, a motor connected at any point of the pipe will be able to use a portion of generated energy.

Definitions

Alternating fluid currents

Considering any flow or pipes,if:

ω = the area section of the pipe measured in square centimeters;
v =the velocity of the fluid at any moment in centimeters per second;

and

i =the flow of liquid in square cubic centimeters per seconds,

then we have:

i =vω

Assuming that the fluid current is produced by a piston having a simple harmonic movement, in a piston cylinder having a section Ω. If we have:

r =the equivalent of driving crank in centimeters
a =the angular velocity of the crank or the pulsations in radians degree per second.
n =the number of crank rotations per second.

Then:

The flow from the cylinder to the pipe is: i = I sin(at+φ)

Where:

I = raΩ (the maximum alternating flow in square centimeters per second; Amplitude of the flow.
t = time in seconds
φ = the angle of the phase

If T= period of a complete alternation (one revolution of the crank) then:

a = 2πn; where n = 1/T

The effective current can be defined by the equation:

I_{eff}^2= \frac{1}{T}\int\limits_{0}^{T}i^2\,dt and the effective velocity is : v_{eff}=  \frac{I_{eff}}{\omega}

The stoke volume δ will be given by the relation:

\delta = 2r\Omega = 2\frac{I}{a}

Alternating pressures

The alternating pressures are very similar with alternating currents in electricity. In a pipe were the currents are flowing, we will have:

p = H \sin{(at+\Phi)}+p_m ;where H is the maximum alternating pressure measured in kilograms per square centimeter. \Phi = the angle of phase; p_m representing the mean pressure in the pipe.

Considering the above formulas:

the minimum pressure is P_{min} =P_m -H and maximum pressure is P_{max}  =P_m +H

If p1 is the pressure at an arbitrary point and p2 pressure in another arbitrary point:

The difference h =p_1-p_2 = H\sin{(at+\Phi)} is defined as instantaneous hydromotive force between point p1 and p2, H representing the amplitude.

The effective hydromotive force will be: H_{eff}  = \frac{H}{\sqrt{2}}

Friction

In alternating current flowing a pipe the friction appear at the surface of the pipe and also in liquid itself. Therefore the relation between the hydromotive and current can be written:

 H =Ri; where R= coefficient of friction in  \frac{kg.sec.}{cm.^5}

Using experiments R may be calculated from formula:

R = \epsilon \frac{\gamma l v_{eff}}{2g \omega d} ;

Where:

If we introduce \epsilon in the formula, we get:

R = \frac{\gamma l}{g \omega} \big( 0.01 \frac{v}{d}+ \frac{0.09}{d} \sqrt{ \frac{v_{eff}}{d}} \big) this is equivalent with:
100k = \frac{v_{eff}}{d} + \frac{9}{d} \sqrt{\frac{v_{eff}}{d}} =\frac{v_{eff}}{d}\big( 1+\frac{9}{v_{eff}} \sqrt{\frac{v_{eff}}{d}} \big); introducing k in formula, result thar R =   k\frac{\gamma l}{g  \omega}

For pipes with greater diameter greater velocity can be achieve for same value of k. The loss of power due to friction is calculated with:

W = \frac{1}{T} \int_0^T hi\,dt, putting h=Ri result:
W =  \frac{1}{T} \int_0^T Ri^2\,dt=\frac{R}{T} \int_0^T i^2\,dt=\frac{RI^2}{2}
Therefore: W =\frac{RI^2}{2}=\frac{HI}{2}=H_{eff}\times I_{eff}

Capacity and condensers

Definition: Hydraulic condensers are appliances for making alterations in value of fluid currents, pressures or phases of alternating fluid currents. The apparatus usually consists of a mobile solid body, which is dividing the liquid column, and fixed elastically in a middle position, in such way that it follows the movements of the liquid column.

The principal function of hydraulic condensers is to counteract inertia effects due to moving masses.

Hydraulic Condenser Drawing Theory
Hydraulic Condenser Example
Hooke's law for spring F = m \frac{\mathrm{d}^2x}{\mathrm{d}t^2} = -k x ; in this case x=f=piston movement.
Simple Harmonic

The principal function of hydraulic condensers is to counteract inertia effects due to moving masses.

The capacity C of a condenser consisting of a piston of section ω on which the liquid pressure is acting, held in mean position by means of springs, is given by the equation:

ΔV=ωΔf=CΔp

where:

ΔV=the variation of volume of the space for liquid;
Δf=the variation of the longitudinal position of the piston,

and

Δp=the variation of the pressure in the liquid.


If the piston is held by a spring at any given moment:

f=AF where
A= a constant depending on the spring


and

F=the force acting on the spring.


In the condenser we will have:

ΔF=ωΔp


and

Δf=AωΔp


Considering the above equations:

C=Aω2


and

F =\frac{f}{A}=\frac{f\omega}{C}

For a spring wire of circular section:

B= Ff

Where

B is the volume of spring in cubic centimeters

and

σ the allowable stress of metal in kilograms per square centimeter.
G the coefficient of transverse elasticity of the metal.

Therefore:

B=mFf

m being a constant depending on σ and G. If d is the diameter of the spring wire and the D the mean diameter of the spring. Then:

F=0.4\frac{d^3}{D}\sigma

so that:

d=\sqrt[3]{\frac{FD}{0.4\sigma} }

if we consider ::n=\sqrt[3]{\frac{1}{0.4\sigma} } then:

d=n\sqrt[3]{FD}

The above equations are used in order to calculate the springs required for a condenser of a given capacity required to work at a given maximum stress.

Notes

  1. https://archive.org/stream/theoryofwavetran00consrich#page/n3/mode/2up
  2. Constantinesco, G. Theory of Sonics: A Treatise on Transmission of Power by Vibrations. The Admiralty, London, 1918
  3. https://archive.org/stream/theoryofwavetran00consrich#page/n3/mode/2up
  4. http://www.imsar.ro/SISOM_Papers_2007/D_18.pdf

References

This article is issued from Wikipedia - version of the Saturday, March 28, 2015. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.