Sputtering

Sputtering is a process whereby particles are ejected from a solid target material due to bombardment of the target by energetic particles,[1] particularly, in the laboratory, gas ions. It only happens when the kinetic energy of the incoming particles is much higher than conventional thermal energies (≫ 1 eV). This process can lead, during prolonged ion or plasma bombardment of a material, to significant erosion of materials, and can thus be harmful. On the other hand, it is commonly utilized for thin-film deposition, etching and analytical techniques.

A commercial AJA Orion sputtering system at Cornell NanoScale Science and Technology Facility.

Physics of sputtering

Physical sputtering is driven by momentum exchange between the ions and atoms in the target materials, due to collisions.[1][2][3]

Sputtering from a linear collision cascade. The thick line illustrates the position of the surface, and the thinner lines the ballistic movement paths of the atoms from beginning until they stop in the material. The purple circle is the incoming ion. Red, blue, green and yellow circles illustrate primary, secondary, tertiary and quaternary recoils, respectively. Two of the atoms happen to move out from the sample, i.e. be sputtered.

The incident ions set off collision cascades in the target. When such cascades recoil and reach the target surface with an energy greater than the surface binding energy, an atom would be ejected, and this process is known as sputtering. If the target is thin on an atomic scale, the collision cascade can reach the back side of the target and atoms can escape the surface binding energy "in transmission". The average number of atoms ejected from the target per incident ion is called the sputter yield and depends on the ion incident angle, the energy of the ion, the masses of the ion and target atoms, and the surface binding energy of atoms in the target. For a crystalline target the orientation of the crystal axes with respect to the target surface is relevant.

The primary particles for the sputtering process can be supplied in a number of ways: for example by a plasma, an ion source, an accelerator or by a radioactive material emitting alpha particles.

A model for describing sputtering in the cascade regime for amorphous flat targets is Thompson's analytical model.[4] An algorithm that simulates sputtering based on a quantum mechanical treatment including electrons stripping at high energy is implemented in the program TRIM.[5]

A different mechanism of physical sputtering is heat spike sputtering. This may occur when the solid is dense enough, and then the incoming ion heavy enough, that the collisions occur very close to each other. Then the binary collision approximation is no longer valid, but rather the collisional process should be understood as a many-body process. The dense collisions induce a heat spike (also called thermal spike), which essentially melts the crystal locally. If the molten zone is close enough to a surface, large numbers of atoms may sputter due to flow of liquid to the surface and/or microexplosions.[6] Heat spike sputtering is most important for heavy ions (say Xe or Au or cluster ions) with energies in the keV–MeV range bombarding dense but soft metals with a low melting point (Ag, Au, Pb, etc.). The heat spike sputtering often increases nonlinearly with energy, and can for small cluster ions lead to dramatic sputtering yields per cluster of the order of 10,000.[7] For animations of such a process see "Re: Displacement Cascade 1" in External links.

Physical sputtering has a well-defined minimum energy threshold equal to or larger than the ion energy at which the maximum energy transfer of the ion to a sample atom equals the binding energy of a surface atom. This threshold typically is somewhere in the range 10–100 eV.

Preferential sputtering can occur at the start when a multicomponent solid target is bombarded and there is no solid state diffusion. If the energy transfer is more efficient to one of the target components, and/or it is less strongly bound to the solid, it will sputter more efficiently than the other. If in an AB alloy the component A is sputtered preferentially, the surface of the solid will, during prolonged bombardment, become enriched in the B component, thereby increasing the probability that B is sputtered such that the composition of the sputtered material will ultimately return to AB.

Electronic sputtering

The term electronic sputtering can mean either sputtering induced by energetic electrons (for example in a transmission electron microscope), or sputtering due to very high-energy or highly charged heavy ions that lose energy to the solid, mostly by electronic stopping power, where the electronic excitations cause sputtering.[8] Electronic sputtering produces high sputtering yields from insulators, as the electronic excitations that cause sputtering are not immediately quenched, as they would be in a conductor. One example of this is Jupiter's ice-covered moon Europa, where a MeV sulfur ion from Jupiter's magnetosphere can eject up to 10,000 H2O molecules.[9]

Potential sputtering

A commercial sputtering system

In the case of multiple charged projectile ions a particular form of electronic sputtering can take place that has been termed potential sputtering.[10][11] In these cases the potential energy stored in multiply charged ions (i.e., the energy necessary to produce an ion of this charge state from its neutral atom) is liberated when the ions recombine during impact on a solid surface (formation of hollow atoms). This sputtering process is characterized by a strong dependence of the observed sputtering yields on the charge state of the impinging ion and can already take place at ion impact energies well below the physical sputtering threshold. Potential sputtering has only been observed for certain target species[12] and requires a minimum potential energy.[13]

Etching and chemical sputtering

Removing atoms by sputtering with an inert gas is called "ion milling" or "ion etching".

Sputtering can also play a role in reactive ion etching (RIE), a plasma process carried out with chemically active ions and radicals, for which the sputtering yield may be enhanced significantly compared to pure physical sputtering. Reactive ions are frequently used in secondary ion mass spectrometry (SIMS) equipment to enhance the sputter rates. The mechanisms causing the sputtering enhancement are not always well understood, although the case of fluorine etching of Si has been modeled well theoretically.[14]

Sputtering observed to occur below the threshold energy of physical sputtering is also often called chemical sputtering.[1][3] The mechanisms behind such sputtering are not always well understood, and may be hard to distinguish from chemical etching. At elevated temperatures, chemical sputtering of carbon can be understood to be due to the incoming ions weakening bonds in the sample, which then desorb by thermal activation.[15] The hydrogen-induced sputtering of carbon-based materials observed at low temperatures has been explained by H ions entering between C-C bonds and thus breaking them, a mechanism dubbed swift chemical sputtering.[16]

Applications and phenomena

Film deposition

Main article: Sputter deposition

Sputter deposition is a method of depositing thin films by sputtering that involves eroding material from a "target" source onto a "substrate" e.g. a silicon wafer. Resputtering, in contrast, involves re-emission of the deposited material, e.g. SiO2 during the deposition also by ion bombardment.

Sputtered atoms are ejected into the gas phase but are not in their thermodynamic equilibrium state, and tend to deposit on all surfaces in the vacuum chamber. A substrate (such as a wafer) placed in the chamber will be coated with a thin film. Sputtering deposition usually uses an argon plasma because argon, a noble gas, will not react with the target material.

Etching

In the semiconductor industry sputtering is used to etch the target. Sputter etching is chosen in cases where a high degree of etching anisotropy is needed and selectivity is not a concern. One major drawback of this technique is wafer damage.

For analysis

Another application of sputtering is to etch away the target material. One such example occurs in secondary ion mass spectrometry (SIMS), where the target sample is sputtered at a constant rate. As the target is sputtered, the concentration and identity of sputtered atoms are measured using Mass Spectrometry. In this way the composition of the target material can be determined and even extremely low concentrations (20 µg/kg) of impurities detected. Furthermore, because the sputtering continually etches deeper into the sample, concentration profiles as a function of depth can be measured.

In space (Celestial Lights)

Sputtering is one of the forms of space weathering, a process that changes the physical and chemical properties of airless bodies, such as asteroids and the Moon. On icy moons, especially Europa, sputtering of photolyzed water from the surface leads to net loss of hydrogen and accumulation of oxygen-rich materials that may be important for life. Sputtering is also one of the possible ways that Mars has lost most of its atmosphere and that Mercury continually replenishes its tenuous surface-bounded exosphere.

References

  1. 1 2 3 R. Behrisch (ed.) (1981). Sputtering by Particle bombardment:. Springer, Berlin. ISBN 978-3-540-10521-3.
  2. ↑ P. Sigmund, Nucl. Instr. Meth. Phys. Res. B (1987). "Mechanisms and theory of physical sputtering by particle impact". Nuclear Instruments and Methods in Physics Research Section B Beam Interactions with Materials and Atoms 27: 1. Bibcode:1987NIMPB..27....1S. doi:10.1016/0168-583X(87)90004-8.
  3. 1 2 R. Behrisch and W. Eckstein (eds.) (2007). Sputtering by Particle bombardment: Experiments and Computer Calculations from Threshold to Mev Energies. Springer, Berlin.
  4. ↑ M.W. Thompson (1962). "Energy spectrum of ejected atoms during the high- energy sputtering of gold". Philos. Mag. 18 (152): 377. Bibcode:1968PMag...18..377T. doi:10.1080/14786436808227358.
  5. ↑ J. F. Ziegler, J. P, Biersack, U. Littmark (1984). The Stopping and Range of Ions in Solids," vol. 1 of series Stopping and Ranges of Ions in Matter. Pergamon Press, New York. ISBN 978-0-08-021603-4.
  6. ↑ Mai Ghaly and R. S. Averback (1994). "Effect of viscous flow on ion damage near solid surfaces". Physical Review Letters 72 (3): 364–367. Bibcode:1994PhRvL..72..364G. doi:10.1103/PhysRevLett.72.364. PMID 10056412.
  7. ↑ S. Bouneau, A. Brunelle, S. Della-Negra, J. Depauw, D. Jacquet, Y. L. Beyec, M. Pautrat, M. Fallavier, J. C. Poizat, and H. H. Andersen (2002). "Very large gold and silver sputtering yields induced by keV to MeV energy Aun clusters (n=1–13)". Phys. Rev. B 65 (14): 144106. Bibcode:2002PhRvB..65n4106B. doi:10.1103/PhysRevB.65.144106.
  8. ↑ T. Schenkel; Briere, M.; Schmidt-Böcking, H.; Bethge, K.; Schneider, D.; et al. (1997). "Electronic Sputtering of Thin Conductors by Neutralization of Slow Highly Charged Ions". Physical Review Letters 78 (12): 2481. Bibcode:1997PhRvL..78.2481S. doi:10.1103/PhysRevLett.78.2481.
  9. ↑ Johnson, R. E.; Carlson, R. W.; Cooper, J. F.; Paranicas, C.; Moore, M. H.; Wong, M. C. (2004). Fran Bagenal, Timothy E. Dowling, William B. McKinnon, ed. Radiation effects on the surfaces of the Galilean satellites. In: Jupiter. The planet, satellites and magnetosphere 1. Cambridge, UK: Cambridge University Press. pp. 485–512. Bibcode:2004jpsm.book..485J. ISBN 0-521-81808-7.
  10. ↑ T. Neidhart; Pichler, F.; Aumayr, F.; Winter, HP.; Schmid, M.; Varga, P.; et al. (1995). "Potential sputtering of lithium fluoride by slow multicharged ions". Physical Review Letters 74 (26): 5280–5283. Bibcode:1995PhRvL..74.5280N. doi:10.1103/PhysRevLett.74.5280. PMID 10058728.
  11. ↑ M. Sporn; Libiseller, G.; Neidhart, T.; Schmid, M.; Aumayr, F.; Winter, HP.; Varga, P.; Grether, M.; Niemann, D.; Stolterfoht, N.; et al. (1997). "Potential Sputtering of Clean SiO2 by Slow Highly Charged Ions". Physical Review Letters 79 (5): 945. Bibcode:1997PhRvL..79..945S. doi:10.1103/PhysRevLett.79.945.
  12. ↑ F. Aumayr and H. P. Winter (2004). "Potential sputtering". Philosophical Transactions of the Royal Society A 362 (1814): 77–102. Bibcode:2004RSPTA.362...77A. doi:10.1098/rsta.2003.1300. PMID 15306277.
  13. ↑ G. Hayderer; Schmid, M.; Varga, P.; Winter, H; Aumayr, F.; Wirtz, L.; Lemell, C.; Burgdörfer, J.; Hägg, L.; Reinhold, C.; et al. (1999). "Threshold for Potential Sputtering of LiF". Physical Review Letters 83 (19): 3948. Bibcode:1999PhRvL..83.3948H. doi:10.1103/PhysRevLett.83.3948.
  14. ↑ T. A. Schoolcraft and B. J. Garrison, Journal of the American Chemical Society (1991). "Initial stages of etching of the silicon Si110 2x1 surface by 3.0-eV normal incident fluorine atoms: a molecular dynamics study". Journal of the American Chemical Society 113 (22): 8221. doi:10.1021/ja00022a005.
  15. ↑ J. Küppers (1995). "The hydrogen surface chemistry of carbon as a plasma facing material". Surface Science Reports 22 (7–8): 249. Bibcode:1995SurSR..22..249K. doi:10.1016/0167-5729(96)80002-1.
  16. ↑ E. Salonen; Nordlund, K.; Keinonen, J.; Wu, C.; et al. (2001). "Swift chemical sputtering of amorphous hydrogenated carbon". Physical Review B 63 (19): 195415. Bibcode:2001PhRvB..63s5415S. doi:10.1103/PhysRevB.63.195415.

External links

Wikimedia Commons has media related to Sputtering.
This article is issued from Wikipedia - version of the Tuesday, February 09, 2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.