Spring (device)

Helical or coil springs designed for tension.
A heavy-duty helical spring designed for compression and tension.
The English longbow – a simple but very powerful spring made of yew, measuring 2 m (6 ft 6 in) long, with a 470 N (105 lbf) draw force
Spring characteristics: (1) progressive, (2) linear, (3) degressive, (4) almost constant, (5) progressive with knee
A machined spring incorporates several features into one piece of bar stock
Military boobytrap firing device from USSR (normally connected to a tripwire) showing spring-loaded firing pin

A spring is an elastic object used to store mechanical energy. Springs are usually made out of spring steel. There are a large number of spring designs; in everyday usage the term often refers to coil springs.

Small springs can be wound from pre-hardened stock, while larger ones are made from annealed steel and hardened after fabrication. Some non-ferrous metals are also used including phosphor bronze and titanium for parts requiring corrosion resistance and beryllium copper for springs carrying electrical current (because of its low electrical resistance).

When a coil spring is compressed or stretched slightly from rest, the force it exerts is approximately proportional to its change in length (this approximation breaks down for larger deflections). The rate or spring constant of a spring is the change in the force it exerts, divided by the change in deflection of the spring. That is, it is the gradient of the force versus deflection curve. An extension or compression spring has units of force divided by distance, for example lbf/in or N/m. Torsion springs have units of torque divided by angle, such as N·m/rad or ft·lbf/degree. The inverse of spring rate is compliance, that is: if a spring has a rate of 10 N/mm, it has a compliance of 0.1 mm/N. The stiffness (or rate) of springs in parallel is additive, as is the compliance of springs in series.

Depending on the design and required operating environment, any material can be used to construct a spring, so long as the material has the required combination of rigidity and elasticity: technically, a wooden bow is a form of spring.

History

Simple non-coiled springs were used throughout human history, e.g. the bow (and arrow). In the Bronze Age more sophisticated spring devices were used, as shown by the spread of tweezers in many cultures. Ctesibius of Alexandria developed a method for making bronze with spring-like characteristics by producing an alloy of bronze with an increased proportion of tin, and then hardening it by hammering after it was cast.

Coiled springs appeared early in the 15th century,[1] in door locks.[2] The first spring powered-clocks appeared in that century[2][3][4] and evolved into the first large watches by the 16th century.

In 1676 British physicist Robert Hooke discovered Hooke's law which states that the force a spring exerts is proportional to its extension.

Types

A spiral torsion spring, or hairspring, in an alarm clock.
A volute spring. Under compression the coils slide over each other, so affording longer travel.
Vertical volute springs of Stuart tank
Tension springs in a folded line reverberation device.
A torsion bar twisted under load
Leaf spring on a truck

Springs can be classified depending on how the load force is applied to them:

They can also be classified based on their shape:

The most common types of spring are:

Other types include :

Physics

Hooke's law

Main article: Hooke's law

As long as they are not stretched or compressed beyond their elastic limit, most springs obey Hooke's law, which states that the force with which the spring pushes back is linearly proportional to the distance from its equilibrium length:

F=-kx, \

where

x is the displacement vector – the distance and direction the spring is deformed from its equilibrium length.
F is the resulting force vector – the magnitude and direction of the restoring force the spring exerts
k is the rate, spring constant or force constant of the spring, a constant that depends on the spring's material and construction. The negative sign indicates that the force the spring exerts is in the opposite direction from its displacement

Coil springs and other common springs typically obey Hooke's law. There are useful springs that don't: springs based on beam bending can for example produce forces that vary nonlinearly with displacement.

If made with constant pitch (wire thickness), conical springs will have a variable rate. However, a conical spring can be made to have a constant rate by creating the spring with a variable pitch. A larger pitch in the larger-diameter coils and a smaller pitch in the smaller-diameter coils will force the spring to collapse or extend all the coils at the same rate when deformed.

Simple harmonic motion

Main article: Harmonic oscillator

Since force is equal to mass, m, times acceleration, a, the force equation for a spring obeying Hooke's law looks like:

F = m a \quad \Rightarrow \quad -k x = m a. \,
The displacement, x, as a function of time. The amount of time that passes between peaks is called the period.

The mass of the spring is small in comparison to the mass of the attached mass and is ignored. Since acceleration is simply the second derivative of x with respect to time,

- k x = m \frac{d^2 x}{dt^2}. \,

This is a second order linear differential equation for the displacement x as a function of time. Rearranging:

\frac{d^2 x}{dt^2} + \frac{k}{m} x = 0, \,

the solution of which is the sum of a sine and cosine:

x(t) = A \sin \left(t \sqrt{\frac{k}{m}} \right) + B \cos \left(t \sqrt{\frac{k}{m}} \right). \,

A and B are arbitrary constants that may be found by considering the initial displacement and velocity of the mass. The graph of this function with B = 0 (zero initial position with some positive initial velocity) is displayed in the image on the right.

Theory

In classical physics, a spring can be seen as a device that stores potential energy, specifically elastic potential energy, by straining the bonds between the atoms of an elastic material.

Hooke's law of elasticity states that the extension of an elastic rod (its distended length minus its relaxed length) is linearly proportional to its tension, the force used to stretch it. Similarly, the contraction (negative extension) is proportional to the compression (negative tension).

This law actually holds only approximately, and only when the deformation (extension or contraction) is small compared to the rod's overall length. For deformations beyond the elastic limit, atomic bonds get broken or rearranged, and a spring may snap, buckle, or permanently deform. Many materials have no clearly defined elastic limit, and Hooke's law can not be meaningfully applied to these materials. Moreover, for the superelastic materials, the linear relationship between force and displacement is appropriate only in the low-strain region.

Hooke's law is a mathematical consequence of the fact that the potential energy of the rod is a minimum when it has its relaxed length. Any smooth function of one variable approximates a quadratic function when examined near enough to its minimum point as can be seen by examining the Taylor series. Therefore, the force—which is the derivative of energy with respect to displacement—will approximate a linear function.

Force of fully compressed spring

F_{max} = \frac{E d^4 (L-n d)}{16 (1+\nu) (D-d)^3 n} \

where

E – Young's modulus
d – spring wire diameter
L – free length of spring
n – number of active windings
\nu – Poisson ratio
D – spring outer diameter

Zero-length springs

"Zero-length spring" is a term for a specially designed coil spring that would exert zero force if it had zero length; if there were no constraint due to the finite wire diameter of such a helical spring, it would have zero length in the unstretched condition. That is, in a line graph of the spring's force versus its length, the line passes through the origin. Obviously a coil spring cannot contract to zero length because at some point the coils will touch each other and the spring will not be able to shorten any more. Zero length springs are made by manufacturing a coil spring with built-in tension (A twist is introduced into the wire as it is coiled, in the manufacturing process. This works because a coiled spring "unwinds" as it is stretched.), so if it could contract further, the equilibrium point of the spring, the point at which its restoring force is zero, occurs at a length of zero. In practice, zero length springs are made by combining a "negative length" spring, made with even more tension so its equilibrium point would be at a "negative" length, with a piece of inelastic material of the proper length so the zero force point would occur at zero length.

A zero length spring can be attached to a mass on a hinged boom in such a way that the force on the mass is almost exactly balanced by the vertical component of the force from the spring, whatever the position of the boom. This creates a horizontal "pendulum" with very long oscillation period. Long-period pendulums enable seismometers to sense the slowest waves from earthquakes. The LaCoste suspension with zero-length springs is also used in gravimeters because it is very sensitive to changes in gravity. Springs for closing doors are often made to have roughly zero length so that they will exert force even when the door is almost closed, so it will close firmly.

Uses

References

  1. ↑ Springs How Products Are Made, 14 July 2007.
  2. 1 2 White, Lynn Jr. (1966). Medieval Technology and Social Change. New York: Oxford Univ. Press. ISBN 0-19-500266-0., p.126-127
  3. ↑ Usher, Abbot Payson (1988). A History of Mechanical Inventions. Courier Dover. ISBN 0-486-25593-X., p.305
  4. ↑ Dohrn-van Rossum, Gerhard (1997). History of the Hour: Clocks and Modern Temporal Orders. Univ. of Chicago Press. ISBN 0-226-15510-2., p.121
  5. ↑ Constant Springs Piping Technology and Products, (retrieved March 2012)
  6. ↑ Variable Spring Supports Piping Technology and Products, (retrieved March 2012)
  7. ↑ See image:
  8. ↑ "Ideal Spring and Simple Harmonic Motion" (PDF). Retrieved 2016-01-11.
  9. ↑ Samuel, Andrew; Weir, John (1999). Introduction to engineering design: modelling, synthesis and problem solving strategies (2 ed.). Oxford, England: Butterworth. p. 134. ISBN 0-7506-4282-3.
  10. ↑ Davis, Thomas Beiber; Nelson, Carl A. Senior. Audel Mechanical Trades Pocket Manual (4 ed.). Hoboken, NJ: Wiley. p. 275. ISBN 978-0-7645-4170-4.

Further reading

External links

Wikimedia Commons has media related to Spring (device).
This article is issued from Wikipedia - version of the Monday, February 15, 2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.