Spalart–Allmaras turbulence model

Overview

The Spalart–Allmaras model is a one-equation model that solves a modelled transport equation for the kinematic eddy turbulent viscosity. The Spalart-Allmaras model was designed specifically for aerospace applications involving wall-bounded flows and has been shown to give good results for boundary layers subjected to adverse pressure gradients. It is also gaining popularity in turbomachinery applications.

In its original form, the Spalart-Allmaras model is effectively a low-Reynolds number model, requiring the viscosity-affected region of the boundary layer to be properly resolved ( y+ ~1 meshes). In ANSYS FLUENT, the Spalart-Allmaras model has been extended with a y+ -insensitive wall treatment (Enhanced Wall Treatment), which allows the application of the model independent of the near wall y+ resolution.

The formulation blends automatically from a viscous sublayer formulation to a logarithmic formulation based on y+. On intermediate grids, (1< y+ <30), the formulation maintains its integrity and provides consistent wall shear stress and heat transfer coefficients. While the y+ sensitivity is removed, it still should be ensured that the boundary layer is resolved with a minimum resolution of 10-15 cells.

The Spalart-Allmaras model was developed for aerodynamic flows. It is not calibrated for general industrial flows, and does produce relatively larger errors for some free shear flows, especially plane and round jet flows. In addition, it cannot be relied on to predict the decay of homogeneous, isotropic turbulence.

It solves a transport equation for a viscosity-like variable \tilde{\nu}. This may be referred to as the Spalart–Allmaras variable.

Original model

The turbulent eddy viscosity is given by

\nu_t = \tilde{\nu} f_{v1}, \quad f_{v1} = \frac{\chi^3}{\chi^3 + C^3_{v1}}, \quad \chi := \frac{\tilde{\nu}}{\nu}
\frac{\partial \tilde{\nu}}{\partial t} + u_j \frac{\partial \tilde{\nu}}{\partial x_j} = C_{b1} [1 - f_{t2}] \tilde{S} \tilde{\nu} + \frac{1}{\sigma} \{ \nabla \cdot [(\nu + \tilde{\nu}) \nabla \tilde{\nu}] + C_{b2} | \nabla \nu |^2 \} - \left[C_{w1} f_w - \frac{C_{b1}}{\kappa^2} f_{t2}\right] \left( \frac{\tilde{\nu}}{d} \right)^2 + f_{t1} \Delta U^2
\tilde{S} \equiv S + \frac{ \tilde{\nu} }{ \kappa^2 d^2 } f_{v2}, \quad f_{v2} = 1 - \frac{\chi}{1 + \chi f_{v1}}
f_w = g \left[ \frac{ 1 + C_{w3}^6 }{ g^6 + C_{w3}^6 } \right]^{1/6}, \quad g = r + C_{w2}(r^6 - r), \quad r \equiv \frac{\tilde{\nu} }{ \tilde{S} \kappa^2 d^2 }
f_{t1} = C_{t1} g_t \exp\left( -C_{t2} \frac{\omega_t^2}{\Delta U^2} [ d^2 + g^2_t d^2_t] \right)
f_{t2} = C_{t3} \exp\left(-C_{t4} \chi^2 \right)
S = \sqrt{2 \Omega_{ij} \Omega_{ij}}

The rotation tensor is given by

\Omega_{ij} = \frac{1}{2} ( \partial u_i / \partial x_j - \partial u_j / \partial x_i )

and d is the distance from the closest surface.

The constants are

\begin{matrix} \sigma &=& 2/3\\ C_{b1} &=& 0.1355\\ C_{b2} &=& 0.622\\ \kappa &=& 0.41\\ C_{w1} &=& C_{b1}/\kappa^2 + (1 + C_{b2})/\sigma \\ C_{w2} &=& 0.3 \\ C_{w3} &=& 2 \\ C_{v1} &=& 7.1 \\ C_{t1} &=& 1 \\ C_{t2} &=& 2 \\ C_{t3} &=& 1.1 \\ C_{t4} &=& 2 \end{matrix}

Modifications to original model

According to Spalart it is safer to use the following values for the last two constants:

\begin{matrix} C_{t3} &=& 1.2 \\ C_{t4} &=& 0.5 \end{matrix}

Other models related to the S-A model:

DES (1999)

DDES (2006)

Model for compressible flows

There are two approaches to adapting the model for compressible flows. In the first approach, the turbulent dynamic viscosity is computed from

\mu_t = \rho \tilde{\nu} f_{v1}

where \rho is the local density. The convective terms in the equation for \tilde{\nu} are modified to

\frac{\partial \tilde{\nu}}{\partial t} + \frac{\partial}{\partial x_j} (\tilde{\nu} u_j)= \mbox{RHS}

where the right hand side (RHS) is the same as in the original model.

Boundary conditions

Walls: \tilde{\nu}=0

Freestream:

Ideally \tilde{\nu}=0, but some solvers can have problems with a zero value, in which case \tilde{\nu}<=\frac{\nu}{2} can be used.

This is if the trip term is used to "start up" the model. A convenient option is to set \tilde{\nu}=5{\nu} in the freestream. The model then provides "Fully Turbulent" behavior, i.e., it becomes turbulent in any region that contains shear.

Outlet: convective outlet.

References

External links

This article is issued from Wikipedia - version of the Tuesday, July 14, 2015. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.