Sodium-ion battery

Sodium-ion batteries (SIB) are a type of rechargeable metal-ion battery that uses sodium ions as charge carriers.^[1][2] sodium is accessible and abundant, making up over 2.6 percent of the Earth's crust.^[3]

Advantages

Battery-grade salts of sodium are cheap and abundant, much more so than those of lithium.^[1][2]

These cells can be completely drained (to zero charge) without damaging the active materials. They can be stored and shipped safely,. Lithium-ion batteries must retain about 30% of charge during storage, enough that they could short-circuit and catch fire during shipment.^[4]

Applications

In 2014 Aquion Energy offered a commercially available sodium-ion battery with cost/kWh capacity similar to a lead acid battery for use as a backup power source for electricity micro-grids.^[5] According to the company, it was 85 percent efficient.

In 2015 researchers announced a device that employed the "18650" format used in laptops, LED flashlights and the Tesla Model S, among other products. Its energy density was claimed to be comparable to lithium iron phosphate battery.^[3]

In 2016 other researchers announced a model for a device that used symmetric manganese dioxide electrodes in a saltwater bath, separated by a membrane that allowed Cl- to cross it. While charging, Na+ ions intercalated into the electrode on one side and Cl- ions migrated across the membrane, reducing salinity by 63%. While discharging, the Na+ ions left the electrode on one side while other Na+ ions entered it on the other side.^[6][7]

Performance

Sodium ion cells have been reported with a voltage of 3.6 volts, able to maintain 115 Ah/kg after 50 cycles, equating to a cathode-specific energy of approximately 400 Wh/kg^[8] Inferior cycling performance limits the ability of non-aqueous Na-ion batteries to compete with commercial Li-ion cells. In 2015 Faradion claimed to have improved cycling in full Na-ion pouch cells using a layered oxide cathode.^[9]

Design

SIBs store energy in chemical bonds of the anode. Charging the battery forces Na⁺ ions to de-intercalate from the cathode and migrate towards the anode. Charge balancing electrons pass from the cathode through the external circuit containing the charger and into the anode. During discharge the process reverses. Once a circuit is completed electrons pass back from the anode to the cathode and the Na⁺ ions travel back to the cathode.^[10]

Anode

Aquion originally used a carbon anode that relied mostly on Pseudocapacitance to store charge, resulting in a low Energy_density and a tilted voltage-charge slope. In many ways, titanium phosphate is similar to iron phosphate used in some other batteries, but with a low (anodic) electrode potential.The initial electrolyte was an aqueous sodium sulphate solution. Later a more soluble <5M NaClO₄ was used.^[11]

Using Na_xC₆ as the anode, the average voltage on the low potential plateau was higher for Na cells than Li cells. Unlike traditional Li cells, which make use of an intercalated graphite anode with a fully lithiated stoichiometry of LiC₆, Na cells do not reversibly bind graphite. This is in part due to the larger ionic radius of the Na⁺ ion compared to the Li⁺ ion, which causes the graphite to expand. For this reason, carbon-based anodes rely on amorphous carbon that consists of spatially disoriented graphene sheets, defects and interstitial pores. These amorphous carbon allotropes can be categorized as hard or soft. Soft carbons can be transformed into graphite through annealing at high temperatures. Hard carbon materials can be derived from feedstocks such as: sugar, starch, fiber and certain polymers.^[12]

Alloy anodes

Metal alloy anodes made of Antimony (Sb), Tin (Sn), Phosphorus (P), Germanium (Ge) and Lead (Pb) have been studied. Carbon anodes provide organic complexes for the storage of Na⁺ ions, while alloyed anodes form inorganic complexes with the Na⁺ ions, such as Na₃Sb, Na₃Sn and Na₃P. This capability gives alloy anodes greater theoretical capacity than carbon. Whereas amorphous carbon has shown capacity between 300-400 mAh g⁻¹, Na₃P has a theoretical capacity of 2596 mAh g⁻¹. However, the alloying process requires a large volume of as much as 400%. This results in fractures and displaces the alloying material, which causes it to passivate and become 'dead weight', unable to accept sodium ions. Unchecked, these volume changes reduce cycle life. Much of anode alloy research focuses on mitigating volume changes and their negative effects .

Cellulose

In one study, tin-coated wood anodes replaced stiff anode bases. The wood fibers proved withstood more than 400 charging cycles. After hundreds of cycles, the wood ended up wrinkled but intact. Computer models indicated that the wrinkles effectively reduce stress during charging and recharging. Na ions move via the fibrous cell walls and diffuse at the tin film surface.^[13][14]

Another study used MoS₂/graphene composite paper as an electrode, yielding 230 Ah/kg with Coulombic efficiency reaching approximately 99%.^[15][16][17]

Cathode

Tests of Na₂FePO₄F and Li₂FePO₄F cathode materials indicated that a sodium iron phosphate cathode can replace a lithium iron phosphate cathode in a Li cell.^[8] The lithium-ion and sodium-ion combination would lower manufacturing costs.^[8]

P2-Na_2/3[Fe_1/2Mn_1/2]O₂ delivered 190  Ah/kg of reversible capacity in sodium cells using electrochemically active Fe³⁺/Fe⁴⁺ redox at room temperature.^[18] Triclinic Na₂FeP₂O₇ was examined as rechargeable sodium ion batteries by a glass-ceramics method. The precursor glass, also made of Na₂FeP₂O₇, was prepared by melt-quenching. Na₂FeP₂O₇ and exhibited 2.9 V, 88 Ah/kg.^[19]

Separately, chromium cathodes employed the reaction:

NaF + (1−x)VPO₄ + xCrPO₄ → NaV_1−xCr_xPO₄F

The effects of Cr doping on cathode performance materials was analyzed in terms of crystal structure, charge/discharge curves and cycle performance and indicated that the Cr-doped materials expressed better cycle stability. The initial reversible capacity was 83.3 Ah/kg and the first charge/discharge efficiency was about 90.3%. The reversible capacity retention of the material was 91.4% after the 20th cycle.^[8][20]

See also

• Aquion Energy
• Lithium-ion battery
• Rechargeable battery
• Salt water battery

References

Galvanic cells Types Voltaic pile Battery Flow battery Trough battery Concentration cell Fuel cell Thermogalvanic cell Primary cell (non-rechargable) Alkaline Aluminium–air Bunsen Chromic acid Clark Daniell Dry Edison-Lalande Grove Leclanché Lithium Mercury Nickel oxyhydroxide Silicon–air Silver oxide Weston Zamboni Zinc–air Zinc–carbon Secondary cell (rechargeable) Automotive Lead–acid gel / VRLA Lithium–air Lithium–ion Lithium polymer Lithium iron phosphate Lithium titanate Lithium–sulfur Dual carbon battery Molten salt Nanopore Nanowire Nickel–cadmium Nickel–hydrogen Nickel–iron Nickel–lithium Nickel–metal hydride Nickel–zinc Polysulfide bromide Potassium-ion Rechargeable alkaline Sodium-ion Sodium–sulfur Vanadium redox Zinc–bromine Zinc–cerium Cell parts Anode Binder Catalyst Cathode Electrode Electrolyte Half-cell Ions Salt bridge Semipermeable membrane