Proximity card

A passive proximity card for door access.

A proximity card controlled turnstile

A passive proximity card with the plastic casing opened to show components: antenna coil and integrated circuit (black object bottom center)

Anatomy of proximity card: coil and IC

The proximity card reader coil of an electronic fare collection system

A proximity card or prox card^[1] is a "contactless" smart card which can be read without inserting it into a reader device, as required by earlier magnetic stripe cards such as credit cards and "contact" type smart cards.^[2] The proximity cards are part of the contactless card technologies. Held near an electronic reader for a moment they enable the identification of an encoded number. The reader usually produces a beep or other sound to indicate the card has been read. Proximity cards typically have a read range up to 50 cm (< 15 inches)^[1] which is the main difference with contactless smartcard with 2 to 10 cm (1 to 3 inches) . The card can often be left in a wallet or purse, and read by simply holding the wallet or purse near the reader. The term "proximity card" refers to the older 125 kHz devices as distinct to the newer 13.56 MHz contactless smartcards.

Proximity cards can't hold more data than a magnetic stripe card. Only contactless smartcards can hold other type of data like electronic funds balance for contactless payment systems, history data for Time & Attendance or biometric templates. When used without encoding data, only with the Card Serial number, contactless smartcard have similar functionalities to Proximity cards.

Today some contact chip have also a contactless interface. Many major banks are offering such cards. These technologies have very little to do with Proximity cards.

Types

Passive cards

Passive 125 kHz cards, the more widely used type which were described above, are powered by radio frequency signals from the reader device and so have a limited range and must be held close to the reader unit.^[2] They are used as keycards for access control doors in office buildings. Contactless smartcards are used for all other applications; library cards, contactless payment systems, and public transit fare cards.

Active cards

Active 125 kHz Prox cards, sometimes called vicinity cards, are powered by an internal lithium battery. They can have a greater range, up to 2 meters (6 ft). Other contactless technologies like UHF (Ultra High Frequency) can reach up to 150 meters (500 ft) and are often used for applications where the card is read inside a vehicle, such as security gates which open when a vehicle with the access card inside approaches, or automated toll collection.^[2] However the battery eventually runs down, and the card must be replaced after 2 to 7 years.

Method of operation

The card and the reader unit communicate with each other through 125 kHz radio frequency fields, (13.56 MHz for the contactless smartcard cards) by a process called resonant energy transfer.^[1]^[2] Passive cards have three components, sealed inside the plastic: an antenna consisting of a coil of wire, a capacitor, and an integrated circuit (IC), which contains the user's ID number in specific formats and no other data. The reader has its own antenna, which continuously transmits a short range radio frequency field.

When the card is placed within range of the reader, the antenna coil and capacitor, which form a tuned circuit, absorb and store energy from the field, resonating like an electrical version of a tuning fork. This energy is rectified to direct current which powers the integrated circuit. The chip sends its ID number or other data to the antenna coil, which transmits it by radio frequency signals back to the reader unit. The reader checks whether the ID number from the card is correct, and then performs whatever function it has been programmed to do. Since all the energy to power the card comes from the reader unit, passive cards must be close to the reader to function, and so have only a limited range.

An active card contains a flat lithium cell in addition to the above components, to power it. The integrated circuit contains a receiver which uses the battery's power to amplify the signal from the reader unit so it is stronger, so it can detect the reader at a greater distance. The battery also powers a transmitter circuit in the chip which transmits a stronger return signal to cover the greater distance.

Standards for Proximity cards contactless smartcards

Proximity cards are all proprietary. This is also the case of the first generation of contactless smartcards, memory based. This means that there is no compatibility between the readers of a specific brand and the cards of another brand. This is the case of all existing memory based brands (Mifare Classic, iCLASS, legic, Felica, ...) contactless smartcards are known to be covered by the ISO/IEC 14443 and/or the ISO/IEC 15693 standards. It defines two types of card ("A" and "B", with different communications protocols), which typically have a range up to 10 cm (4 inches). The related ISO/IEC 15693 (vicinity card) standard, which typically works up to a longer range of 100 cm (35 inches). The reality is that ISO/IEC 14443 as well as ISO/IEC 15693 can only be fully implemented on microprocessor based cards. The best way to check if a technology meets ISO standard is to ask if it can be emulated on other devices without any proprietary hardware.

125 kHz Readers and formats

The card readers communicate in various protocols, for example the Wiegand protocol that consists of a data 0 and a data 1 circuit (or binary or simple on/off (digital) type circuit). Other known protocols are mono directional Clock and Data or bidirectional OSDP (RS 485), RS 232 or UART. The earliest card formats were up to 64 bits long. As demand has increased bit size has increased to continue to provide unique numbers. Often, the first several bits can be made identical; these are called facility or site code. The idea is that company A has a facility code of xn and a card set of 0001 through 1000 and company B has a facility code of yn and a card set also of 0001 through 1000. For smartcards a numbering system is internationally harmonized and allocated by Netherlands-based NEN (registration authority) as international registration authority according to ISO/IEC 6523 and ISO/IEC 15459 standards.

References

1 2 3 Reid, Robert N. (2005). Facility manager's guide to security: protecting your assets. The Fairmont Press. pp. 144–146. ISBN 0881734837.
1 2 3 4 Norman, Thomas L. (2011). Electronic Access Control. Elsevier. pp. 57–58. ISBN 0123820286.

This article is issued from Wikipedia - version of the Tuesday, January 05, 2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.