Overhead power line

This article is about power lines for general transmission of electrical power. For overhead lines used to power road and rail vehicles, see Overhead line.

Overhead power line in Gloucestershire, England.

An overhead power line is a structure used in electric power transmission and distribution to transmit electrical energy along large distances. It consists of one or more conductors (commonly multiples of three) suspended by towers or poles. Since most of the insulation is provided by air, overhead power lines are generally the lowest-cost method of power transmission for large quantities of electric energy.

Towers for support of the lines are made of wood (as-grown or laminated), steel (either lattice structures or tubular poles), and occasionally reinforced wood. The bare wire conductors on the line are generally made of aluminum (either plain or reinforced with steel, or composite materials such as carbon and glass fiber), though some copper wires are used in medium-voltage distribution and low-voltage connections to customer premises. A major goal of overhead power line design is to maintain adequate clearance between energized conductors and the ground so as to prevent dangerous contact with the line, and to provide reliable support for the conductors, resilient to storms, ice load, earthquakes and other potential causes of damage.^[1] Today overhead lines are routinely operated at voltages exceeding 765,000 volts between conductors, with even higher voltages possible in some cases.

Classification by operating voltage

High- and medium-voltage power lines in Łomża, Poland

Overhead power transmission lines are classified in the electrical power industry by the range of voltages:

Low voltage (LV) – less than 1000 volts, used for connection between a residential or small commercial customer and the utility.
Medium voltage (MV; distribution) – between 1000 volts (1 kV) and to 69 kV, used for distribution in urban and rural areas.
High voltage (HV; subtransmission less than 100 kV; subtransmission or transmission at voltage such as 115 kV and 138 kV), used for sub-transmission and transmission of bulk quantities of electric power and connection to very large consumers.
Extra high voltage (EHV; transmission) – over 230 kV, up to about 800 kV, used for long distance, very high power transmission.
Ultra high voltage (UHV) – higher than 800 kV.

Structures

Circuits

A single-circuit transmission line carries conductors for only one circuit. For a three-phase system, this implies that each tower supports three conductors.

A double-circuit transmission line has two circuits. For three-phase systems, each tower supports and insulates six conductors. Single phase AC-power lines as used for traction current have four conductors for two circuits. Usually both circuits operate at the same voltage.

In HVDC systems typically two conductors are carried per line, but in rare cases only one pole of the system is carried on a set of towers.

In some countries like Germany most power lines with voltages above 100 kV are implemented as double, quadruple or in rare cases even hextuple power line as rights of way are rare. Sometimes all conductors are installed with the erection of the pylons; often some circuits are installed later. A disadvantage of double circuit transmission lines is that maintenance works can be more difficult, as either work in close proximity of high voltage or switch-off of 2 circuits is required. In case of failure, both systems can be affected.

The largest double-circuit transmission line is the Kita-Iwaki Powerline.

A single-circuit line
A double-circuit line
Parallel single-circuit lines
Four circuits on one tower line

Insulators

Medium-voltage power lines with ceramic insulators in California

Modular suspension insulators are used for high-voltage lines.

Insulators must support the conductors and withstand both the normal operating voltage and surges due to switching and lightning. Insulators are broadly classified as either pin-type, which support the conductor above the structure, or suspension type, where the conductor hangs below the structure. The invention of the strain insulator was a critical factor in allowing higher voltages to be used.

At the end of the 19th century, the limited electrical strength of telegraph-style pin insulators limited the voltage to no more than 69,000 volts. Up to about 33 kV (69 kV in North America) both types are commonly used.^[1] At higher voltages only suspension-type insulators are common for overhead conductors.

Insulators are usually made of wet-process porcelain or toughened glass, with increasing use of glass-reinforced polymer insulators. However, with rising voltage levels, polymer insulators (silicone rubber based) are seeing increasing usage.^[5] China has already developed polymer insulators having a highest system voltage of 1100 kV and India is currently developing a 1200 kV (highest system voltage) line which will initially be charged with 400 kV to be upgraded to a 1200 kV line.

Suspension insulators are made of multiple units, with the number of unit insulator disks increasing at higher voltages. The number of disks is chosen based on line voltage, lightning withstand requirement, altitude, and environmental factors such as fog, pollution, or salt spray. In cases where these conditions are suboptimal, longer insulators must be used. Longer insulators with longer creepage distance for leakage current, are required in these cases. Strain insulators must be strong enough mechanically to support the full weight of the span of conductor, as well as loads due to ice accumulation, and wind.^[6]

Porcelain insulators may have a semi-conductive glaze finish, so that a small current (a few milliamperes) passes through the insulator. This warms the surface slightly and reduces the effect of fog and dirt accumulation. The semiconducting glaze also ensures a more even distribution of voltage along the length of the chain of insulator units.

Polymer insulators by nature have hydrophobic characteristics providing for improved wet performance. Also, studies have shown that the specific creepage distance required in polymer insulators is much lower than that required in porcelain or glass. Additionally, the mass of polymer insulators (especially in higher voltages) is approximately 50% to 30% less than that of a comparative porcelain or glass string. Better pollution and wet performance is leading to the increased use of such insulators.

Insulators for very high voltages, exceeding 200 kV, may have grading rings installed at their terminals. This improves the electric field distribution around the insulator and makes it more resistant to flash-over during voltage surges.

Conductors

Sample cross-section of ACSR power line

The most common conductor in use for transmission today is aluminum conductor steel reinforced (ACSR). Also seeing much use is all-aluminum-alloy conductor (AAAC). Aluminum is used because it has about half the weight of a comparable resistance copper cable (though larger diameter due to lower specific conductivity), as well as being cheaper.^[1] Copper was more popular in the past and is still in use, especially at lower voltages and for grounding. Bare copper conductors are light green.

While larger conductors may lose less energy due to lower electrical resistance, they are more costly than smaller conductors. An optimization rule called Kelvin's Law states that the optimum size of conductor for a line is found when the cost of the energy wasted in the conductor is equal to the annual interest paid on that portion of the line construction cost due to the size of the conductors. The optimization problem is made more complex by additional factors such as varying annual load, varying cost of installation, and the discrete sizes of cable that are commonly made.^[1]

Since a conductor is a flexible object with uniform weight per unit length, the geometric shape of a conductor strung on towers approximates that of a catenary. The sag of the conductor (vertical distance between the highest and lowest point of the curve) varies depending on the temperature and additional load such as ice cover. A minimum overhead clearance must be maintained for safety. Since the temperature of the conductor increases with increasing heat produced by the current through it, it is sometimes possible to increase the power handling capacity (uprate) by changing the conductors for a type with a lower coefficient of thermal expansion or a higher allowable operating temperature.

Conventional ACSR and modern carbon core conductors

Two such conductors that offer reduced thermal sag are known as composite core conductors (ACCR and ACCC conductor). In lieu of steel core strands that are often used to increase overall conductor strength, the ACCC conductor uses a carbon and glass fiber core that offers a coefficient of thermal expansion about 1/10 of that of steel. While the composite core is nonconductive, it is substantially lighter and stronger than steel, which allows the incorporation of 28% more aluminum (using compact trapezoidal shaped strands) without any diameter or weight penalty. The added aluminum content helps reduce line losses by 25 to 40% compared to other conductors of the same diameter and weight, depending upon electric current. The carbon core conductor's reduced thermal sag allows it to carry up to twice the current ("ampacity") compared to all-aluminum conductor (AAC) or ACSR.

Power lines sometimes have spherical markers to meet International Civil Aviation Organization recommendations.^[7]

The power lines and their surroundings must be maintained by linemen, sometimes assisted by helicopters with pressure washers or circular saws which may work 3 times faster. However this work often occurs in the dangerous areas of the Helicopter height–velocity diagram.^[8]^[9]^[10]

Bundle Conductors^[11]

A bundle conductor

For transmission of power across long distances, high voltage transmission is employed. Transmission higher than 300 kV poses some problems, such as the corona effect, which cause significant power loss and interference with communication circuits. In order to reduce this corona effect, it is preferable to use more than one conductor per phase, or bundled conductors.

Bundle conductors consist of several parallel cables connected at intervals by spacers, often in a cylindrical configuration. The optimum number of conductors depends on the current rating, but typically higher-voltage lines also have higher current. There is also some advantage due to lower corona loss. American Electric Power^[12] is building 765 kV lines using six conductors per phase in a bundle. Spacers must resist the forces due to wind, and magnetic forces during a short-circuit.

Spacer damper for four-conductor bundles

Bundle conductor attachment

Advantages

Bundled conductors reduce the voltage gradient in the vicinity of the line. This reduces the possibility of corona discharge. At extra high voltage, the electric field gradient at the surface of a single conductor is high enough to ionize air, which wastes power, generates unwanted audible noise and interferes with communication systems. The field surrounding a bundle of conductors is similar to the field that would surround a single, very large conductor—this produces lower gradients which mitigates issues associated with high field strength.
Improvements in the transmission efficiency as loss due to corona effect is countered.
Bundled conductor lines will have higher capacitance in comparison with single lines. Thus, they will have higher charging currents, which helps in improving power factor.
When transmitting alternating current, bundle conductors also avoid the reduction in ampacity of a single large conductor due to the skin effect.
A bundle conductor also has lower reactance, compared to a single conductor.
Additionally, bundled conductors cool themselves more efficiently due to the increased surface area of the conductors, further reducing line losses.
The increased GMR reduces line reactance and inductance.

Inductance and Bundled Conductors

Two-conductor bundle with equal spacing

Three-conductor bundle with equal spacing

In addition to reducing corona losses and improving the skin effect, conductor bundling also reduces line inductance. Low line inductance is highly desired because it reduces reactive current flow, line heating, and voltage drop across transmission lines. For a non-bundled transmission line, two parameters of transmission lines affect the inductance: the geometric mean radius, $D$ , and the equivalent conductor radius, $r x$ . The geometric mean radius is the geometric mean of the distance between phases in a bundled or non-bundled transmission line. For example, a 3-phase system with equal line spacing $d$ and conductors arranged in a straight line has a geometric mean radius of $D = (d . d . 2d)^{1 \over 3}$ where $2 d$ represents the distance between the two outermost phases. The conductor radius $r x$ is the effective radius of a single conductor. The equation for inductance is then:

$L = 2\bullet10^{-7} \bullet \ln \left ( {D\bullet e^{1 \over 4} \over r_x} \right )$ where e is the natural logarithm base

Usually, the $r x$ value is tabulated because it depends on the exact composition of the conductor and inductive properties that result—these are hard to describe analytically especially in the case of composite conductors. Typical values of $r x$ range from 6 to 18 mm.^[13] For a bundled transmission cable, two additional factors affect the line inductance: the bundle diameter $D B$ and the geometric arrangement of the bundle. These two parameters can be used to calculate an effective bundled cable radius, $D BE$ .^[14]

Two-Conductor Bundle Equation:

D_{BE} = \sqrt{r_x . D_B}

Three-Conductor Bundle Equation:

D_{BE} = \sqrt[3]{r_x . (D_B)^2}

Four-Conductor Bundle Equation:

D_{BE} = \sqrt[4]{r_x . (D_B)^2.D_B\sqrt{2}}

n

-Conductor Bundle Equation:

D_{BE} = { D_B \over{2.sin ( { \pi\pi\pi \over{n} } ) } }.\sqrt[n]{n.r_x.2.sin( { \pi\over{n} } )\over {D_B}}

^[15]

The resulting line inductance equation is nearly identical, however the equivalent bundle diameter DBE is substituted for the effective cable radius r_x.

$L = 2\bullet10^{-7} \bullet \ln \left ( {D\bullet e^{1 \over 4} \over D_{BE}} \right )$ where e is the natural logarithm base

Inductance Improvements for Bundled Conductors
Line inductance (per meter) vs. Bundle Diameter for AC power transmission
Line inductance (per meter) vs. Phase Spacing for AC power transmission

All of the above effects can be attributed to the concept of Geometric Mean Radius (GMR). By putting several cylindrical cables together to attain a single large cable, the action in effect increases the radius of the unit, lowering the inductance of the conductor. The assumption when carrying out this calculation is that the distance between phases are much larger than the GMR of each conductor.

Disadvantages

Bundled conductors have higher wind loading, although much lower than the solid tube of equal diameter which they resemble electrically.
Bundled conductors are also more expensive and difficult to install.

Ground wires

Overhead power lines are often equipped with a ground conductor (shield wire or overhead earth wire). The ground conductor is usually grounded (earthed) at the top of the supporting structure, to minimize the likelihood of direct lightning strikes to the phase conductors.^[16] In circuits with earthed neutral, it also serves as a parallel path with the earth for fault currents. Very high-voltage transmission lines may have two ground conductors. These are either at the outermost ends of the highest cross beam, at two V-shaped mast points, or at a separate cross arm. Older lines may use surge arresters every few spans in place of a shield wire; this configuration is typically found in the more rural areas of the United States. By protecting the line from lightning, the design of apparatus in substations is simplified due to lower stress on insulation. Shield wires on transmission lines may include optical fibers (optical ground wires/OPGW), used for communication and control of the power system.

At some HVDC converter stations, the ground wire is used also as the electrode line to connect to a distant grounding electrode. This allows the HVDC system to use the earth as one conductor. The ground conductor is mounted on small insulators bridged by lightning arrestors above the phase conductors. The insulation prevents electrochemical corrosion of the pylon.

Medium-voltage distribution lines may also use one or two shield wires, or may have the grounded conductor strung below the phase conductors to provide some measure of protection against tall vehicles or equipment touching the energized line, as well as to provide a neutral line in Wye wired systems.

On some power lines for very high voltages in the former Soviet Union, the ground wire is used for PLC-radio systems and mounted on insulators at the pylons.

Insulated conductors and cable

Overhead insulated cables are rarely used, usually for short distances (less than a kilometer). Insulated cables can be directly fastened to structures without insulating supports. An overhead line with bare conductors insulated by air is typically less costly than a cable with insulated conductors.

A more common approach is "covered" line wire. It is treated as bare cable, but often is safer for wildlife, as the insulation on the cables increases the likelihood of a large-wing-span raptor to survive a brush with the lines, and reduces the overall danger of the lines slightly. These types of lines are often seen in the eastern United States and in heavily wooded areas, where tree-line contact is likely. The only pitfall is cost, as insulated wire is often costlier than its bare counterpart. Many utility companies implement covered line wire as jumper material where the wires are often closer to each other on the pole, such as an underground riser/pothead, and on reclosers, cutouts and the like.

Compact transmission lines

A compact overhead transmission line requires a smaller right of way than a standard overhead powerline. Conductors must not get too close to each other. This can be achieved either by short span lengths and insulating crossbars, or by separating the conductors in the span with insulators. The first type is easier to build as it does not require insulators in the span, which may be difficult to install and to maintain.

Examples of compact lines are:

Compact transmission lines may be designed for voltage upgrade of existing lines to increase the power that can be transmitted on an existing right of way.^[17]

Low voltage

Aerial bundled cable in Old Coulsdon, Surrey

Low voltage overhead lines may use either bare conductors carried on glass or ceramic insulators or an aerial bundled cable system. The number of conductors may be anywhere between four (three phase plus a combined earth/neutral conductor - a TN-C earthing system) up to as many as six (three phase conductors, separate neutral and earth plus street lighting supplied by a common switch).

Train power

Main article: Overhead line

Overhead lines or overhead wires are used to transmit electrical energy to trams, trolleybuses or trains. Overhead line is designed on the principle of one or more overhead wires situated over rail tracks. Feeder stations at regular intervals along the overhead line supply power from the high-voltage grid. For some cases low-frequency AC is used, and distributed by a special traction current network.

Further applications

Overhead lines are also occasionally used to supply transmitting antennas, especially for efficient transmission of long, medium and short waves. For this purpose a staggered array line is often used. Along a staggered array line the conductor cables for the supply of the earth net of the transmitting antenna are attached on the exterior of a ring, while the conductor inside the ring, is fastened to insulators leading to the high-voltage standing feeder of the antenna.

Use of area under overhead power lines

A man working on powerlines in Nauru (2007)

Use of the area below an overhead line is limited because objects must not come too close to the energized conductors. Overhead lines and structures may shed ice, creating a hazard. Radio reception can be impaired under a power line, due both to shielding of a receiver antenna by the overhead conductors, and by partial discharge at insulators and sharp points of the conductors which creates radio noise.

In the area surrounding the overhead lines it is dangerous to risk interference; e.g. flying kites or balloons, using ladders or operating machinery.

Overhead distribution and transmission lines near airfields are often marked on maps, and the lines themselves marked with conspicuous plastic reflectors, to warn pilots of the presence of conductors.

Construction of overhead power lines, especially in wilderness areas, may have significant environmental effects. Environmental studies for such projects may consider the effect of bush clearing, changed migration routes for migratory animals, possible access by predators and humans along transmission corridors, disturbances of fish habitat at stream crossings, and other effects.

Interface of aviation with power lines

General aviation, hang gliding, paragliding, skydiving, and kite flying have important interface with power lines. Nearly every kite product warns users to stay away from power lines. Many deaths occur when aircraft (powered and unpowered) crash into power lines. Some power lines are marked with visibility bulbs. The placement of power lines sometimes use up sites that would otherwise be used by hang gliders.^[18]^[19]

History

The first transmission of electrical impulses over an extended distance was demonstrated on July 14, 1729 by the physicist Stephen Gray. The demonstration used damp hemp cords suspended by silk threads (the low resistance of metallic conductors not being appreciated at the time).

However the first practical use of overhead lines was in the context of telegraphy. By 1837 experimental commercial telegraph systems ran as far as 20 km (13 miles). Electric power transmission was accomplished in 1882 with the first high-voltage transmission between Munich and Miesbach (60 km). 1891 saw the construction of the first three-phase alternating current overhead line on the occasion of the International Electricity Exhibition in Frankfurt, between Lauffen and Frankfurt.

In 1912 the first 110 kV-overhead power line entered service followed by the first 220 kV-overhead power line in 1923. In the 1920s RWE AG built the first overhead line for this voltage and in 1926 built a Rhine crossing with the pylons of Voerde, two masts 138 meters high.

In 1953, the first 345 kV line was put into service by American Electric Power in the United States. In Germany in 1957 the first 380 kV overhead power line was commissioned (between the transformer station and Rommerskirchen). In the same year the overhead line traversing of the Strait of Messina went into service in Italy, whose pylons served the Elbe crossing 1. This was used as the model for the building of the Elbe crossing 2 in the second half of the 1970s which saw the construction of the highest overhead line pylons of the world. Earlier, in 1952, the first 380 kV line was put into service in Sweden, in 1000 km (625 miles) between the more populated areas in the south and the largest hydroelectric power stations in the north. Starting from 1967 in Russia, and also in the USA and Canada, overhead lines for voltage of 765 kV were built. In 1982 overhead power lines were built in Russia between Elektrostal and the power station at Ekibastusz, this was a three-phase alternating current line at 1150 kV (Powerline Ekibastuz-Kokshetau). In 1999, in Japan the first powerline designed for 1000 kV with 2 circuits were built, the Kita-Iwaki Powerline. In 2003 the building of the highest overhead line commenced in China, the Yangtze River Crossing.

Mathematical analysis

An overhead power line is one example of a transmission line. At power system frequencies, many useful simplifications can be made for lines of typical lengths. For analysis of power systems, the distributed resistance, series inductance, shunt leakage resistance and shunt capacitance can be replaced with suitable lumped values or simplified networks.

Short and medium line model

A short length of a power line (less than 80 km) can be approximated with a resistance in series with an inductance and ignoring the shunt admittances. This value is not the total impedance of the line, but rather the series impedance per unit length of line. For a longer length of line (80–250 km), a shunt capacitance is added to the model. In this case it is common to distribute half of the total capacitance to each side of the line. As a result, the power line can be represented as a two-port network, such as ABCD parameters.^[20]

The circuit can be characterized as

Z = z l = (R + j \omega L)l

where

Z is the total series line impedance
z is the series impedance per unit length
l is the line length
$\omega \$ is the sinusoidal angular frequency

The medium line has an additional shunt admittance

Y = y l = j \omega C l

where

Y is the total shunt line admittance
y is the shunt admittance per unit length

Short length of power line
Medium length of power line

References

Wikimedia Commons has media related to Overhead power lines.

1 2 3 4 5 6 7 8 Donald G. Fink and H. Wayne Beaty, Standard Handbook for Electrical Engineers, Eleventh Edition, McGraw-Hill, New York, 1978, ISBN 0-07-020974-X, Chapter 14 Overhead Power Transmission
↑ "Powering Up - Vertical Magazine - The Pulse of the Helicopter Industry". verticalmag.com. Archived from the original on 4 October 2015. Retrieved 4 October 2015.
↑ Sunrise Powerlink Helicopter Operations on YouTube
↑ The Straight Dope: Why are thin wires strung along the tops of high-voltage transmission towers?
↑ NGK-Locke Polymer insulator manufacturer
↑ Advanced Rubber Products - Suspension Insulators
↑ "Chapter 6. Visual aids for denoting obstacles" (PDF). Annex 14 Volume I Aerodrome design and operations. International Civil Aviation Organization. 2004-11-25. Retrieved 1 June 2011. 6.2.8 ... spherical ... diameter of not less than 60 cm. ... 6.2.10 ... should be of one colour.
↑ Head, Elan (April 2015). "High-value cargo". Vertical Magazine. p. 80-90. Retrieved 11 April 2015.
↑ Maher, Guy R. (April 2015). "A cut above". Vertical Magazine. p. 92-98. Archived from the original on 11 May 2015. Retrieved 11 April 2015.
↑ Harnesk, Tommy. "Helikoptermonterad motorsåg snabbkapar träden" Ny Teknik, 9 January 2015. Accessed: 12 January 2015.
↑ Grainger, John J. and W. D. Stevenson Jr. Power System Analysis and Design, 2nd edition. McGraw Hill (1994).
↑ Freimark, Bruce (October 1, 2006). "Six Wire Solution]". Transmission & Distribution World. Retrieved March 6, 2007.
↑ (Table A4) Duncan Glover et al.
↑ Glover, Duncan; Sarma, Overbye (2012). Power System Analysis and Design (Fifth ed.). Stamford, CT: Cengage Learning. p. 828. ISBN 978-1-111-42577-7.
↑ Gary, Claude; Moreau, Marcel (1976). L'effet de couronne en tension alternative. France: Eyrolles. pp. 11–12.
↑ The Art and Science of Lightning Protection.
↑ Beaty, H. Wayne; Fink, Donald G. , Standard Handbook for Electrical Engineers (15th Edition) McGraw-Hill, 2007 978-0-07-144146-9 pages 14-105 through 14-106
↑ Aircraft Accidents Due to Overhead Power Lines
↑ Pacific Gas and Electric Company Reminds Customers About Flying Kites Safely.
↑ J. Glover, M. Sarma, and T. Overbye, Power System Analysis and Design, Fifth Edition, Cengage Learning, Connecticut, 2012, ISBN 978-1-111-42577-7, Chapter 5 Transmission Lines: Steady-State Operation

Overhead power line

Classification by operating voltage