Optimized Link State Routing Protocol

"OLSR" redirects here. For ordinary least squares regression, see Ordinary least squares.

The Optimized Link State Routing Protocol (OLSR)[1] is an IP routing protocol optimized for mobile ad hoc networks, which can also be used on other wireless ad hoc networks. OLSR is a proactive link-state routing protocol, which uses hello and topology control (TC) messages to discover and then disseminate link state information throughout the mobile ad hoc network. Individual nodes use this topology information to compute next hop destinations for all nodes in the network using shortest hop forwarding paths.

Diagram of OLSR data flow.

Features specific to OLSR

Link-state routing protocols such as Open Shortest Path First (OSPF) and IS-IS elect a designated router on every link to perform flooding of topology information. In wireless ad hoc networks, there is different notion of a link, packets can and do go out the same interface; hence, a different approach is needed in order to optimize the flooding process. Using Hello messages the OLSR protocol at each node discovers 2-hop neighbor information and performs a distributed election of a set of multipoint relays (MPRs). Nodes select MPRs such that there exists a path to each of its 2-hop neighbors via a node selected as an MPR. These MPR nodes then source and forward TC messages that contain the MPR selectors. This functioning of MPRs makes OLSR unique from other link state routing protocols in a few different ways: The forwarding path for TC messages is not shared among all nodes but varies depending on the source, only a subset of nodes source link state information, not all links of a node are advertised but only those that represent MPR selections.

Since link-state routing requires the topology database to be synchronized across the network, OSPF and IS-IS perform topology flooding using a reliable algorithm. Such an algorithm is very difficult to design for ad hoc wireless networks, so OLSR doesn't bother with reliability; it simply floods topology data often enough to make sure that the database does not remain unsynchronized for extended periods of time.

Benefits

Being a proactive protocol, routes to all destinations within the network are known and maintained before use. Having the routes available within the standard routing table can be useful for some systems and network applications as there is no route discovery delay associated with finding a new route.

The routing overhead generated, while generally greater than that of a reactive protocol, does not increase with the number of routes being created.

Default and network routes can be injected into the system by HNA messages allowing for connection to the internet or other networks within the OLSR MANET cloud. Network routes are something reactive protocols do not currently execute well.

Timeout values and validity information is contained within the messages conveying information allowing for differing timer values to be used at differing nodes.

Criticisms

The original definition of OLSR does not include any provisions for sensing of link quality; it simply assumes that a link is up if a number of hello packets have been received recently. This assumes that links are bi-modal (either working or failed), which is not necessarily the case on wireless networks, where links often exhibit intermediate rates of packet loss. Implementations such as the open source OLSRd (commonly used on Linux-based mesh routers) have been extended (as of v. 0.4.8) with link quality sensing.

Being a proactive protocol, OLSR uses power and network resources in order to propagate data about possibly unused routes. While this is not a problem for wired access points, and laptops, it makes OLSR unsuitable for sensor networks that try to sleep most of the time. For small scale wired access points with low CPU power, the open source OLSRd project showed that large scale mesh networks can run with OLSRd on thousands of nodes with very little CPU power on 200 MHz embedded devices.

Being a link-state protocol, OLSR requires a reasonably large amount of bandwidth and CPU power to compute optimal paths in the network. In the typical networks where OLSR is used (which rarely exceed a few hundreds of nodes), this does not appear to be a problem.

By only using MPRs to flood topology information, OLSR removes some of the redundancy of the flooding process, which may be a problem in networks with moderate to large packet loss rates[2] – however the MPR mechanism is self-pruning (which means that in case of packet losses, some nodes that would not have retransmitted a packet, may do so).

Messages

OLSR makes use of "Hello" messages to find its one hop neighbors and its two hop neighbors through their responses. The sender can then select its multipoint relays (MPR) based on the one hop node that offers the best routes to the two hop nodes. Each node has also an MPR selector set, which enumerates nodes that have selected it as an MPR node. OLSR uses topology control (TC) messages along with MPR forwarding to disseminate neighbor information throughout the network. Host and network association (HNA) messages are used by OLSR to disseminate network route advertisements in the same way TC messages advertise host routes.

Hello

Topology control (TC)

Other approaches

The problem of routing in ad hoc wireless networks is actively being researched, and OLSR is but one of several proposed solutions. To many, it is not clear whether a whole new protocol is needed, or whether OSPF could be extended with support for wireless interfaces.[3][4]

In bandwidth- and power-starved environments, it is interesting to keep the network silent when there is no traffic to be routed. Reactive routing protocols do not maintain routes, but build them on demand. As link-state protocols require database synchronisation, such protocols typically use the distance vector approach, as in AODV and DSDV, or more ad hoc approaches that do not necessarily build optimal paths, such as Dynamic Source Routing.

For more information see the list of ad hoc routing protocols.

OLSR version 2

OLSRv2 has been published by the IETF in April 2014.[5] It maintains many of the key features of the original including MPR selection and dissemination. Key differences are the flexibility and modular design using shared components: packet format packetbb, and neighborhood discovery protocol NHDP. These components are being designed to be common among next generation IETF MANET protocols. Differences in the handling of multiple address and interface enabled nodes is also present between OLSR and OLSRv2.

Implementations

See also

References

  1. ↑ RFC 3626
  2. ↑ M. Abolhasan, B. Hagelstein, J. C.-P. Wang (2009). "Real-world performance of current proactive multi-hop mesh protocols".
  3. ↑ Extensions to OSPF to Support Mobile Ad Hoc Networking, Madhavi Chandra, Abhay Roy, Mar-10, RFC 5820
  4. ↑ MANET Extension of OSPF using CDS Flooding, Richard Ogier, Phil Spagnolo, Aug-09, RFC 5614
  5. ↑ RFC 7181

External links

This article is issued from Wikipedia - version of the Monday, January 25, 2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.