M1917 Browning machine gun

The M1917 Browning machine gun is a heavy machine gun used by the United States armed forces in World War I, World War II, Korea, and to a limited extent in Vietnam; it has also been used by other nations. It was a crew served, belt-fed, water-cooled machine gun that served alongside the much lighter air-cooled Browning M1919. It was used at the battalion level, and often mounted on vehicles (such as a jeep). There were two main iterations of it: the M1917, which was used in World War I; and the M1917A1; which was used thereafter. The M1917, which was used on some aircraft as well as in a ground role, had a firing rate of 450 rounds per minute; the M1917A1 had a firing rate of 450 to 600 rounds per minute.

Design and development

Val Browning, the inventor's son, demonstrates the M1917.

US Army 2nd Lieutenant Valmore A. Browning firing a Browning machine gun. This gun was used in the Argonne Sector and is being tested by 2nd Lt. Browning at Thillombois, Meuse, France, October 5, 1918.

Marines push back a Japanese counterattack during the Battle of Cape Gloucester in 1944.

In 1900, John Moses Browning filed a patent for a recoil-powered automatic gun.^[2] Browning did not work on the gun again until 1910, when he built a water-cooled prototype of the 1900 design.^[3] Although the gun worked well, Browning improved the design slightly. Browning replaced side ejection with bottom ejection, added a buffer for smoother operation, replaced the hammer with a two piece firing pin, and some other minor improvements.^[4] The basic design of the gun was still the 1900 design.

The Browning is a water-cooled heavy machine gun, though some experimental versions were made that did not use a water jacket; the air-cooled M1919 was later developed as a medium machine gun. Unlike many other early machine guns, the M1917 had nothing to do with Maxim's toggle lock design. At 47 pounds (21 kg), it was much lighter than contemporary Maxim type guns such as the first 137-pound (62 kg) German Maschinengewehr 08 (08/15 model: 43 lb (20 kg)) and the British Vickers machine gun, while still being highly reliable. The only similarities with the Maxim or Vickers are the principle of recoil operation, T-slot breechblock, "pull-out" belt feed, water cooling, and forward ejection. Its sliding-block locking mechanism saved weight and complexity, and was used in many previous Browning designs. The belt fed left-to-right, and the cartridges were stacked closer together than Maxim/Vickers (patterns copied by most guns later.)

The Army Ordnance Department showed little interest in machine guns until war was declared in April 1917. At that time, the U.S. arsenal included only 1,100 machine guns, and most of those were outmoded.^[5] The government asked several designers to submit weapons. Browning arranged a test at the Springfield Armory in May 1917.^[6] In the first test, the weapon fired 20,000 rounds without incident. The reliability was exceptional, so Browning fired another 20,000 rounds through the weapon without any parts failing. The Ordnance Board was impressed, but was unconvinced that the same level of performance could be achieved in a production model. Consequently, Browning used a second gun that not only duplicated the original trial, but it also fired continuously for 48 minutes and 12 seconds (over 21,000 rounds).^[7]

The Army adopted the weapon as its principal heavy machine gun, utilizing the M1906 .30-06 cartridge with a 150-grain, flat-base bullet. Unfortunately, production was a problem. Several manufacturers started producing the gun, but they had to set up the assembly lines and tooling. By June 30, 1918, Westinghouse had made only 2,500 and Remington had made only 1,600. By the time of the Armistice, Westinghouse had made 30,150, Remington 12,000, and Colt 600.^[8]

Until the start of World War I, the Army had used a variety of older machine guns, like the M1895 Colt–Browning machine gun "Potato Digger" (which Browning had also designed) and weapons like the Maxim Gun, the Benet–Mercie M1909, and the Hotchkiss M1914 machine gun. Although the Model 1917 was intended to be the principal US Army heavy machine gun in the war, the Army was, in fact, forced to purchase many foreign weapons - the French-produced Hotchkiss 8 mm machine gun was actually the most numerous heavy machine gun used by the American Expeditionary Force.

In 1926, the Browning's rear sight was revised to incorporate scales for both the new M1 Ball (172-grain boat-tail bullet) and the M1906 (150-grain flat-base bullet) ammunition.^[9] With M1 ball, the M1917 had a maximum range of about 5,500 yd (5,000 m); with M2 ammunition, about 3,500 yd (3,200 m).^[9] The rear sight had a battle sight as well as a raised leaf-type sight suitable for employment against either ground or air targets.^[9]

Service

The M1917 saw limited service in the later days of World War I. Because of production delays, only about 1,200 Model 1917s saw combat in the conflict, and then only in the last 2½ months of the war. Some arrived too late for combat service. For example, the 6th Machine Gun Battalion, fighting as part of the Second Division didn't exchange their Hotchkiss M1914 machine guns for Browning M1917 machine guns until November 14, three days after the armistice.^[10] The U.S. equipped about a third of the divisions sent to France; the others were equipped equally with machine guns bought from the French or the British Vickers machine guns built by Colt in the US. Where the Model 1917 did see action, its rate of fire and reliability were highly effective. The M1917 weapon system was inferior to the Vickers and Hotchkiss guns because the British and French cartridges had about 50 percent longer range than the .30-06 service cartridge used in World War I.^[11]

A U.S. Marine firing his Browning M1917 machine gun at the Japanese at Battle of Iwo Jima

A Browning M1917 in action during the Korean War.

The Model 1917A1 was again used in the Second World War, and was primarily used with the M2 ball, tracer, and armor-piercing ammunition introduced just prior to the outbreak of hostilities. Some were supplied to the UK for use by the Home Guard since all production of the .303 Vickers were needed to resupply the equipment abandoned during the Fall of France. The M1917's weight and bulk meant that it was generally employed as a fixed defense or as a battalion or regimental support weapon. At the fierce battle of Momote Airstrip in the Admiralties, the US Army's 5th Cavalry machinegunners killed several hundred Japanese in one night using their M1917 Brownings; one gun was left in position after the battle as a memorial to the desperate struggle.^[12]

The Model 1917 was called to service again in the Korean War. On at least one occasion, U.S. soldiers in the Korean War urinated on the gun when water-cooling had failed in the frigid temperatures of the Korean winter.^[13] The Model 1917 was slowly phased out of military service in the late 1960s in favor of the much lighter M60 machine gun chambered in the new 7.62mm NATO cartridge.

The attributes of the Model 1917 (and similar weapons, such as the Vickers machine gun)—continuous fire from a static position—had been rendered useless by the transition to highly mobile warfare. Many of the 1917s were given to South Vietnam. The last ones in regular US service were on the machine gun infiltration course at Fort Benning, Georgia, where their sustained-fire capability was an advantage in long nights of shooting over the heads of low-crawling trainees. The gun did continue to see service in some Third World armies well into the later half of the 20th century. Some are still in use today by irregular military forces because its water cooled barrel allows for long periods of sustained fire.

M1917 and M1917A1 Ammunition Chests

The machine gun used a wooden ammunition chest that carried 250 rounds.
The early M1917 model had an angled corner and a leather strap handle on top.
The later M1917A1 model had a square corner and a cloth strap handle on top.

The wooden ammunition belt chest was replaced during WWII by the expendable metal Box Ammunition M1 adopted May 6, 1942. On June 20, 1945, a modified version known as the M1A1 was adopted. The M1A1 had a spring-loaded catch to fasten it to the M1917A1 tripod more securely and provide a better watertight seal. In the late 1940s the M19 box replaced the earlier metal M1 and M1A1 boxes, and a modified version known as the M19A1 appeared in the early 1950s and continues in use today.^[14]

Variants

US military variants

M1917

The original gun suffered from a weakness related to the design of the receiver - under field conditions, the bottom plates, which were dovetailed into the gun's two side plates, tore out. An early fix was to attach a roughly horseshoe-shaped steel bracket around the rearmost part of the receiver. A later fix was to rivet "stirrups" (right-angled steel pieces) to the bottom and side plates. The stirrup fix became the standard reinforcement until a more permanent fix for the problem was developed. [Another reported problem was bulging in the sideplates, which was probably caused by stresses put into the sideplates when hammering the dovetails closed.]

M1917A1

An M1917A1 in Hackenberg museum (Veckring, Moselle, France)

In the 1930s, the Ordnance Bureau developed a new bottom plate, which had side flanges that came up on both side of the bottom of the receiver, that was attached to the side plates by rivets. This fixed the problem of the original bottom plates and became standard for all M1917 and M1919 series machine guns. While the US Arsenal at Rock Island was the leader in converting the existing stocks of M1917 series guns over to 1917A1 configuration, other arsenals took part. In addition, the rear sights were updated for the new ammunition and the new sights did away with the World War I multiple aperture disk on the rear sight. The top covers also had a stronger feed pawl pivot arm installed, so the gun could handle the stress of pulling an ammunition belt the distance from the ground. Rock Island Arsenal also developed an all-steel water jacket that went into production around 1943; this was stronger than the earlier brass capped jackets. These steel components were interchangeable with the earlier brass ones to allow for repair of worn or damaged water jacket components.

Other changes were implemented, some during the war, but not all M1917s received these updates. Beginning in 1938, the pivot in the top cover was replaced with a new one that would become standard on all M1919 series guns. While the World War I pattern top cover hinge pin appears to have been retained on most converted M1917s, the later production M1917A1s had a positive locking top cover hinge pin that allowed the top cover to remain open lessening the chance of it dropping closed on one's hands while working on the gun - this became the standard on all M1919 series guns.

M1918

Air-cooled aircraft version of the M1917. Developed during the First World War, the M1918 arrived too late, but became the dominant weapon of its type in US service until the development of the M1919. It features a heavier barrel, but lighter barrel jacket as compared to the M1917. A sub-variant, the M1918M1, was developed as a flexible version of the fixed M1918.

International variants & designations

The M1917 pattern has been used in countries the world over in a variety of forms. In certain cases a new designation was applied by the user nation.

Type 30

Chinese designation for locally produced M1917s chambered in 7.92×57mm Mauser.

Ksp m/14-29 and ksp m/36

Kulspruta m/14-29 was the Swedish designation for the licensed M1917A1, produced by Carl Gustafs Gevärsfaktori in Eskilstuna, for infantry support. The main differences was that it was chambered in the standard calibre 6.5×55mm, had spade-grips and used the cooling jacket and tripod of the m/14 (Schwarzlose) tripod, the machine gun the Ksp m/14-29 replaced. Reason for replacement was simply manufacturing costs: 50 machine guns using the Browning mechanism could be made to the same cost as 30 Schwarzlose, which was discovered during the manufacture of Kulspruta m/22.^[15]

The 6.5mm bullet was found to be too light for long-range fire support and anti-aircraft use, so in 1932 the heavier 8×63mm patron m/32 cartridge was developed. As this resulted in a heavier recoil, a spring-loaded cradle replaced the backplate with a heavily spring-loaded buffer that acted as an extension of the standard Browning recoil buffer. This also replaced the regular spade-grips with the ones integrated in the cradle. The cradle, now part of the weapon, would then be hooked onto a tripod m/36. This tripod featured, beside a 5×25 power optical sight, advanced elevation- and traverse controls. The unprecedented recoil control and steadiness of the tripod made Dolf Goldsmith remark that this arrangement “was undoubtedly the most accurate long-range rifle-caliber machine gun ever made”.^[15][16] For anti-air purposes, a double cradle was made to hold a matching pair of m/36. The right gun, lacking sights altogether, was fed from the right, while the left gun, with iron sights complemented with an AA sight ring, was fed from left. The cocking handles were located between the guns, while safety and triggers were individual for left and right. The special AA tripod had elongated legs and chains to either secure the tripod or hang weights on it for extra stability.^[15] These double cradles were also used as standard defence, mounted on a ring on the cab roof, on terrain vehicles and armoured troop carriers like Terrängbil m/42 KP. The latter was used with good effect in the Congo-crisis in the early 1960s. Until 1966, the m/14-29 and m/36 machine guns could use both the 6.5mm and the 8mm ammunition. Converting between the two was a matter of exchanging barrel, cartridge stop and bolt.^[15]

In 1966, most were converted to 7.62×51mm NATO.^[16] Some old models were retained in training use to use up the stores of obsolete ammunition.^[16] After the stocks were expended in the 1970s, all guns were re-barrelled to 7.62mm NATO.^[16][17][18] The weapons were finally taken out of service in the 1990s.^[16]

Ckm wz.30

The Ckm wz.30 was an unlicensed Polish-built clone of the M1917 chambered in 7.92×57mm Mauser.^[19] The modifications included new iron sights (V-notch rather than loophole), lengthened butt handle, lengthened barrel, simplified rifle lock for easier exchange of used-up barrels and better handling, mounting adapted for both anti-personnel and AA fire and sights and grips adapted to suit both purposes. Roughly 8,000 were built by Państwowa Fabryka Karabinów.

M/29

Norwegian M/29 in anti-aircraft configuration on the Narvik front in 1940

Norwegian designation for the Colt M1917 (mentioned in the following section) in 7.92 mm, used as the standard HMG and anti-aircraft weapon for the Norwegian Army from 1929 to 1940.^[20][21] The M/29 replaced the Hotchkiss M1914 machine gun in Norwegian service.^[21] In all, 1,800 M/29s were in Norwegian service by the time of the 9 April 1940 German invasion.^[22] The M/29 saw sterling service in the 1940 Norwegian Campaign, often deployed as the only heavy weapon of Norwegian front line units.

Commercial variants

Colt Model 1917 and Model 1928

Colt commercially produced the M1917, and also under contract to the Argentine government a number of slightly modified guns as the Model 1928.

The Model 1928 featured a thumb safety, Type A flash hider, and a mount for a panoramic sight unit.

Colt MG38, MG38B, and MG38BT

Derivatives of the Colt M1928 for general commercial sale.

The 38 and 38B were water-cooled with a barrel jacket threaded inside the trunnion, unlike the M1917 and Colt Model 1928.

The 38BT was a short heavy barreled air-cooled weapon resembling the Browning M1919A2, designed for use in tanks.

The 38 series also features spade grips, not found on the rest of the M1917 and the majority of the M1919 families.

Derivatives

A simplified, air-cooled version of the weapon, the Model 1919, was adopted after World War I and saw action in World War II, the Korean War, the Vietnam War, and the Congo crisis.

Users

•  Argentina
•  Australia
•  Belgium Used by Belgian forces during the Korean War
•  Brazil
•  Republic of China (locally produced copies chambered for 7.92 mm Mauser rounds)^[23]
•  Democratic Republic of the Congo (ex-Swedish m/36 guns)
•  Dominican Republic
•  Indonesia
•  South Korea
•  Malaysia (used by the eighth route army)
•  Norway
•  Philippines
•  Poland
•  Sweden (designated as Kulspruta (Ksp) m/36)
•  Thailand (designated as the Type 66)
•  United Kingdom
•  United States: was the standard medium machine gun until it was replaced by the M60 machine gun from 1957. It was used in the Reserves and National Guard until the 1960s.
•  Vietnam
•  South Vietnam

See also

• List of U.S. Army weapons by supply catalog designation SNL A-5

Weapons of comparable role, performance and era

• Vickers gun
• M1919 Browning machine gun

Popular Culture

The M1917 Browning is featured prominently in the denouement of Sam Peckinpah's The Wild Bunch. ^[24]

Notes

External links

• Gothia Association for Weapon History on the Ksp m/36
• Segel, Robert G. (Fall 2009). "The Model 1917 Browning Water-Cooled Machine Gun" (PDF). Small Arms Defense Journal: 60–69. 

M1917 Browning machine gun derivatives M1917 M1919 M2 M73 Mk 19 Ckm wz.30 XM174

John Browning Semi-automatic pistols FN M1900 Colt M1900 Colt M1902 FN Model 1903 M1903 Pocket Hammer M1903 Pocket Hammerless FN M1905 M1908 Vest Pocket FN Model 1910 M1911 Colt Woodsman Baby Browning Hi-Power Rifles Winchester Model 1885 Winchester Model 1886 Winchester 1892 Winchester Model 1894 Winchester Model 1895 Remington Model 8 Remington Model 24 FN Trombone Shotguns Winchester Model 1887 Winchester Model 1897 Browning Auto-5/Remington Model 11 Remington Model 17 Stevens Model 520/620 Browning Superposed Ithaca 37 Machine guns Colt–Browning M1895 Browning M1917 Browning Automatic Rifle Browning M1919 M2 Machine Gun Cartridges .25 ACP .32 ACP .38 ACP .380 ACP 9mm Browning Long .45 ACP .50 BMG