Lunarcrete

Laboratory-determined properties for lunarcrete[1][2]
Compressive strength 39–75.7 N/mm2 (MPa)
Young's modulus 21.4 kN/m2
Density 2.6 g/cm3
Temperature coefficient 5.4 × 10−6 K−1

Lunarcrete, also known as "mooncrete", an idea first proposed by Larry A. Beyer of the University of Pittsburgh in 1985, is a hypothetical aggregate building material, similar to concrete, formed from lunar regolith, that would reduce the construction costs of building on the Moon.[3]

Ingredients

Only comparatively small amounts of moon rock have been transported to Earth, so in 1988 researchers at the University of North Dakota proposed simulating the construction of such a material by using lignite coal ash.[3] Other researchers have used the subsequently developed lunar regolith simulant materials, such as JSC-1 (developed in 1994 and as used by Toutanji et al.).[4] Some small-scale testing, with actual regolith, has been performed in laboratories, however.[2]

The basic ingredients for lunarcrete would be the same as those for terrestrial concrete: aggregate, water, and cement. In the case of lunarcrete, the aggregate would be lunar regolith. The cement would be manufactured by beneficiating lunar rock that had a high calcium content. Water would either be supplied from off the moon, or by combining oxygen with hydrogen produced from lunar soil.[2]

Lin et al. used 40g of the lunar regolith samples obtained by Apollo 16 to produce lunarcrete in 1986.[5] The lunarcrete was cured by using steam on a dry aggregate/cement mixture. Lin proposed that the water for such steam could be produced by mixing hydrogen with lunar ilmenite at 800 °C, to produce titanium oxide, iron, and water. It was capable of withstanding compressive pressures of 75 MPa, and lost only 20% of that strength after repeated exposure to vacuum.[6]

In 2008, Houssam Toutanji, of the University of Alabama in Huntsville, and Richard Grugel, of the Marshall Space Flight Center, used a lunar soil simulant to determine whether lunarcrete could be made without water, using sulfur (obtainable from lunar dust) as the binding agent. The process to create this sulfur concrete required heating the sulfur to 130–140 °C. After exposure to 50 cycles of temperature changes, from -27 °C to room temperature, the simulant lunarcrete was found to be capable of withstanding compressive pressures of 17MPa, which Toutanji and Grugel believed could be raised to 20MPa if the material were reinforced with silica (also obtainable from lunar dust).[7]

Casting and production

There would need to be significant infrastructure in place before industrial scale production of lunarcrete could be possible.[2]

The casting of lunarcrete would require a pressurized environment, because attempting to cast in a vacuum would simply result in the water sublimating, and the lunarcrete failing to harden. Two solutions to this problem have been proposed: premixing the aggregate and the cement and then using a steam injection process to add the water, or the use of a pressurized concrete fabrication plant that produces pre-cast concrete blocks.[2][8]

Lunarcrete shares the same lack of tensile strength as terrestrial concrete. One suggested lunar equivalent tensioning material for creating pre-stressed concrete is lunar glass, also formed from regolith, much as fibreglass is already sometimes used as a terrestrial concrete reinforcement material.[2] Another tensioning material, suggested by David Bennett, is Kevlar, imported from Earth (which would be cheaper, in terms of mass, to import from Earth than conventional steel).[8]

Sulfur based "Waterless Concrete"

This proposal is based on the observation that water is likely to be a precious commodity on the Moon. Also sulfur gains strength in a very short time and doesn't need any period of cooling, unlike hydraulic cement. This would reduce the time that human astronauts would need to be exposed to the surface lunar environment.[9][10]

Sulfur is present on the moon in the form of the mineral troilite, (FeS)[11] and could be reduced to obtain sulfur. It also doesn't require the ultra high temperatures needed for extraction of cementitious components (e.g. anorthosites).

"Sulfur "concrete" is an established construction material. Strictly speaking it isn't a concrete as there is little by way of chemical reaction. Instead the sulfur acts as a thermoplastic material binding with a non reactive substrate. Cement and water are not required. The concrete doesn't have to be cured, instead it is simply heated to above the melting point of sulfur, 140 °C, and after cooling it reaches high strength immediately.

The best mixture for tensile and compressive strength is 65% JSC-1 lunar regolith simulant and 35% sulfur, with an average compressive strength of 33.8 MPa and tensile strength of 3.7 MPa. Addition of 2% metal fiber increase the compressive strength to 43.0 MPa[12] Addition of silica also increases the strength of the concrete.[13]

This sulfur concrete could be of especial value for dust minimization, for instance to create a launching pad for rockets leaving the Moon.[11]

Issues for "Sulfur Concrete"

It provides less protection from cosmic radiation, so walls would need to be thicker than concrete walls (the water in concrete is an especially good absorber of cosmic radiation).

Sulfur melts at 115.2 °C, and lunar temperatures in high latitudes can reach 123 Celsius at midday. In addition, the temperature changes could change the volume of the sulfur concrete due to polymorphic transitions in the sulfur.[11] (see Allotropes of sulfur).

[14]

So unprotected sulfur concrete on the Moon, if directly exposed to the surface temperatures, would need to be limited to higher latitudes or shaded locations with maximum temperatures less than 96 °C and monthly variations not exceeding 114 °C.

The material would degrade through repeated temperature cycles, but the effects are likely to be less extreme on the Moon due to the slowness of the monthly temperature cycle. The outer few millimeters may be damaged through sputtering from impact of high energy particles from the solar wind and solar flares. This may however be easy to repair, by reheating or recoating the surface layers in order to sinter away cracks and heal the damage.

Use

David Bennett, of the British Cement Association, argues that lunarcrete has the following advantages as a construction material for lunar bases:[8]

He observes, however, that lunarcrete is not an airtight material, and to make it airtight would require the application of an epoxy coating to the interior of any lunarcrete structure.[8]

Bennett suggests that hypothetical lunar buildings made of lunarcrete would most likely use a low-grade concrete block for interior compartments and rooms, and a high-grade dense silica particle cement-based concrete for exterior skins.[8]

See also

References

  1. ↑ J. A. Happel (1993). "Indigenous materials for lunar construction". Applied Mechanics Reviews (American Society of Mechanical Engineers) 46 (6): 313–325. Bibcode:1993ApMRv..46..313H. doi:10.1115/1.3120360.
  2. 1 2 3 4 5 6 F. Ruess, J. Schaenzlin, and H. Benaroya (July 2006). "Structural Design of a Lunar Habitat" (PDF). Journal of Aerospace Engineering (American Society of Civil Engineers) 19 (3): 138. doi:10.1061/(ASCE)0893-1321(2006)19:3(133).
  3. 1 2 "UND Engineers Would Like to Follow the Lunarcrete Road". Grand Forks Herald (North Dakota). 1988-02-28.
  4. ↑ H. Toutanji, M. R. Fiske, and M. P. Bodiford (2006). "Development and Application of Lunar "Concrete" for Habitats". In Ramesh B. Malla, Wieslaw K. Binienda, and Arup K. Maji. Proceedings of 10th Biennial International Conference on Engineering, Construction, and Operations in Challenging Environments (Earth & Space 2006) and 2nd NASA/ARO/ASCE Workshop on Granular Materials in Lunar and Martian Exploration held in League City/Houston, TX, during March 5–8, 2006. Reston, VA: American Society of Civil Engineers. pp. 1–8. doi:10.1061/40830(188)69. ISBN 0784408300.
  5. ↑ François Spiero and David C. Dunand (1997). "Simulation of Martian Materials and Resources Exploitation on a Variable Gravity Research Facility". In Thomas R. Meyer. The Case for Mars IV: the international exploration of Mars — consideration for sending humans : proceedings of the fourth Case for Mars Conference held June 4–8, 1990, at the University of Colorado, Boulder, Colorado. Univelt for the American Astronautical Society. p. 356. ISBN 9780877034216.
  6. ↑ George William Herbert (1992-11-17). Norman Yarvin, ed. "Luna concrete". Archives: Space: Science, Exploration.
  7. ↑ Colin Barras (2008-10-17). "Astronauts Could Mix DIY Concrete for Cheap Moon Base". New Scientist.
  8. 1 2 3 4 5 6 7 8 9 D. F. H. Bennett (2002). "Concrete: the material — Lunar concrete". Innovations in concrete. Thomas Telford Books. pp. 86–88. ISBN 0-7277-2005-8.
  9. ↑ Performance of “Waterless Concrete” Houssam A. Toutanji Steve Evans Richard N. Grugel
  10. ↑ PRODUCTION OF LUNAR CONCRETE USING MOLTEN SULFUR, Final Research Report for JoVe NASA Grant NAG8 - 278, Dr. Husam A. Omar Department of Civil Engineering University of South Alabama
  11. 1 2 3 I. Casanova (1997). "Feasibility and Applications of Sulfur Concrete for Lunar Base Development: A Preliminary Study" (PDF). 28th Annual Lunar and Planetary Science Conference, March 17–21, 1997, Houston, TX. p. 209.
  12. ↑ PRODUCTION OF LUNAR CONCRETE USING MOLTEN SULFUR Final Research Report for JoVe NASA Grant NAG8 - 278 by Dr. Husam A. Omar
  13. ↑ Strength and Durability Performance of Waterless Lunar Concrete Houssam Toutanji, Becca Glenn-Loper, and Beth Schrayshuen
  14. ↑ Houssam Toutanji, Becca Glenn-Loper, and Beth Schrayshuen (2005). "Strength and Durability Performance of Waterless Lunar Concrete" (PDF). 43rd AIAA Aerospace Sciences Meeting and Exhibit 10 – 13 January 2005, Reno, Nevada. American Institute of Aeronautics and Astronautics.

Further reading

This article is issued from Wikipedia - version of the Monday, January 18, 2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.