Isochron dating

Isochron dating is a common technique of radiometric dating and is applied to date certain events, such as crystallization, metamorphism, shock events, and differentiation of precursor melts, in the history of rocks. Isochron dating can be further separated into mineral isochron dating and whole rock isochron dating; both techniques are applied frequently to date terrestrial and also extraterrestrial rocks (meteorites). The advantage of isochron dating as compared to simple radiometric dating techniques is that no assumptions are needed about the initial amount of the daughter nuclide in the radioactive decay sequence. Indeed, the initial amount of the daughter product can be determined using isochron dating. This technique can be applied if the daughter element has at least one stable isotope other than the daughter isotope into which the parent nuclide decays.

Basis for method

All forms of isochron dating assume that the source of the rock or rocks contained unknown amounts of both radiogenic and non-radiogenic isotopes of the daughter element, along with some amount of the parent nuclide. Thus, at the moment of crystallization, the ratio of the concentration of the radiogenic isotope of the daughter element to that of the non-radiogenic isotope is some value independent of the concentration of the parent. As time goes on, some amount of the parent decays into the radiogenic isotope of the daughter, increasing the ratio of the concentration of the radiogenic isotope to that of the daughter. The greater the initial concentration of the parent, the greater the concentration of the radiogenic daughter isotope will be at some particular time. Thus, the ratio of the daughter to non-radiogenic isotope will become larger with time, while the ratio of parent to daughter will become smaller. For rocks that start out with a small concentration of the parent, the daughter/non-radiogenic ratio will not change quickly as compared to rocks starting with a large concentration of the parent.

Isochron plots

To perform dating, a rock is crushed to a fine powder, and minerals are separated by various physical and magnetic means. Each mineral has different ratios between parent and daughter concentrations. For each mineral, the ratios are related by the following equation:

{ D+\Delta{P}_t \over D_i } = {\Delta{P}_t \over P-\Delta{P}_t } \left ( { P-\Delta{P}_t \over D_i }\right ) + {D \over D_i}          (1)

where

D is the initial concentration of the daughter isotope,
D_i is the concentration of the non-radiogenic isotope of the daughter element (assumed constant),
P is the initial concentration of the parent isotope, and
\Delta{P}_t is the total amount of the parent isotope which has decayed by time t.

The proof of (1) amounts to simple algebraic manipulation. It is useful in this form because it exhibits the relationship between quantities that actually exist at present. To wit, P-\Delta{P}_t, D+\Delta{P}_t and D_i respectively correspond to the concentrations of parent, daughter and non-radiogenic isotopes found in the rock at the time of measurement.

The ratios D+\Delta{P}_t \over D_i (relative concentration of daughter and non-radiogenic isotopes) and { P-\Delta{P}_t \over D_i } (relative concentration of parent and non-radiogenic isotope) are measured by mass spectrometry and plotted against each other in a three-isotope plot known as an isochron plot. Ratios are used instead of absolute concentrations because mass spectrometers usually measure the former rather than the latter. (See particularly the section on isotope ratio mass spectrometry.)

If all data points lie on a straight line, this line is called an isochron. The better the fit of the data points to a line, the more reliable the resulting age estimate. Since the ratio of the daughter and non-radiogenic isotopes is proportional to the ratio of the parent and non-radiogenic isotopes, the slope of the isochron gets steeper with time. The change in slope from initial conditions—assuming an initial isochron slope of zero (a horizontal isochron) at the point of intersection (intercept) of the isochron with the y-axis—to the current computed slope gives the age of the rock. The slope of the isochron, \Delta{P}_t \over P-\Delta{P}_t, represents the ratio of daughter to parent as used in standard radiometric dating.

Whole rock isochron dating uses the same ideas but instead of different minerals obtained from one rock uses different types of rocks that are derived from a common reservoir; e.g. the same precursor melt. It is possible to date the differentiation of the precursor melt which then cooled and crystallized into the different types of rocks.

One of the best known isotopic systems for isochron dating is the rubidium-strontium system. Other systems that are used for isochron dating include samarium-neodymium, and uranium-lead. Some isotopic systems based on short living extinct radionuclides such as 53Mn, 26Al, 129I, 60Fe and others are used for isochron dating of events in the early history of the solar system. However, methods using extinct radionuclides give only relative ages and have to be calibrated with radiometric dating techniques based on long living radionuclides like Pb-Pb-dating to give absolute ages.

Application

Isochron dating is useful in the determination of the age of igneous rocks, which have their initial origin in the cooling of liquid magma. It is also useful to determine the time of metamorphism, shock events (such as the consequence of an asteroid impact) and other events depending of the behaviour of the particular isotopic systems under such events.

See also

External links

This article is issued from Wikipedia - version of the Saturday, June 20, 2015. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.