Hydraulic fluid

Hydraulic fluid being poured.

Hydraulic fluid(s), also called hydraulic liquid(s), are the medium by which power is transferred in hydraulic machinery. Common hydraulic fluids are based on waste, mineral oil or water.[1] Examples of equipment that might use hydraulic fluids include excavators and backhoes, hydraulic brakes, power steering systems, transmissions, garbage trucks, aircraft flight control systems, lifts, and industrial machinery.

Hydraulic systems like the ones mentioned above will work most efficiently if the hydraulic fluid used has zero compressibility.

Functions and properties

The primary function of a hydraulic fluid is to convey power. In use, however, there are other important functions of hydraulic fluid such as protection of the hydraulic machine components. The table below lists the major functions of a hydraulic fluid and the properties of a fluid that affect its ability to perform that function:[2]

Function Property
Medium for power transfer and control
  • Non compressible (high bulk modulus)
  • Fast air release
  • Low foaming tendency
  • Low volatility
Medium for heat transfer
  • Good thermal capacity and conductivity
Sealing Medium
Lubricant
  • Viscosity for film maintenance
  • Low temperature fluidity
  • Thermal and oxidative stability
  • Hydrolytic stability / water tolerance
  • Cleanliness and filterability
  • Demulsibility
  • Antiwear characteristics
  • Corrosion control
Pump efficiency
  • Proper viscosity to minimize internal leakage
  • High viscosity index
Special function
  • Fire resistance
  • Friction modifications
  • Radiation resistance
Environmental impact
Functioning life
  • Material compatibility

Composition

Base stock

The original hydraulics fluid, dating back to the time of ancient Egypt, was water. Beginning in the 1920s, mineral oil began to be used more than water as a base stock due to its inherent lubrication properties and ability to be used at temperatures above the boiling point of water. Today most hydraulic fluids are based on mineral oil base stocks.

Natural oils such as rapeseed (also called canola oil) are used as base stocks for fluids where biodegradability and renewable sources are considered important.

Other base stocks are used for specialty applications, such as for fire resistance and extreme temperature applications. Some examples include: glycol, esters, organophosphate ester, polyalphaolefin, propylene glycol, and silicone oils.

NaK-77, an eutectic alloy of sodium-potassium, can be used as a hydraulic fluid in high-temperature and high-radiation environments, for temperature ranges of 10 to 1400 °F (-12 to 1033 °C). Its bulk modulus at 1000 °F (538 °C) is 310,000 psi (2.14 GPa), higher than of a hydraulic oil at room temperature. Its lubricity is poor, so positive-displacement pumps are unsuitable and centrifugal pumps have to be used. Addition of caesium shifts the useful temperature range to -95 to 1300 °F (-70 to 977 °C). The NaK-77 alloy was tested in hydraulic and fluidic systems for the Supersonic Low Altitude Missile.[3]

Other components

Hydraulic fluids can contain a wide range of chemical compounds, including: oils, butanol, esters (e.g. phthalates, like DEHP, and adipates, like bis(2-ethylhexyl) adipate), polyalkylene glycols (PAG), organophosphate (e.g. tributylphosphate), silicones, alkylated aromatic hydrocarbons, polyalphaolefins (PAO) (e.g. polyisobutenes), corrosion inhibitors (incl acid scavengers), anti-erosion additives, etc.

Biodegradable hydraulic fluids

Environmentally sensitive applications (e.g. farm tractors and marine dredging) may benefit from using biodegradable hydraulic fluids based upon rapeseed (Canola) vegetable oil when there is the risk of an oil spill from a ruptured oil line. Typically these oils are available as ISO 32, ISO 46, and ISO 68 specification oils. ASTM standards ASTM-D-6006, Guide for Assessing Biodegradability of Hydraulic Fluids and ASTM-D-6046, Standard Classification of Hydraulic Fluids for Environmental Impact are relevant.

Brake fluid

Brake fluid is a subtype of hydraulic fluid with high boiling point, both when new (specified by the equilibrium boiling point) and after absorption of water vapor (specified by wet boiling point). Under the heat of braking, both free water and water vapor in a braking system can boil into a compressible vapor, resulting in brake failure.[4] Glycol-ether based fluids are hygroscopic, and absorbed moisture will greatly reduce the boiling point over time. Mineral oil and silicone based fluids are not hygroscopic.

None of these fluids mix, so it is important to use the type the vehicle was designed to use.[5] The system contains rubber seals that will be damaged with use of the incorrect fluid.

Power Steering Fluid

Power steering fluid is a subtype of hydraulic fluid. Most are mineral oil or silicone based fluids, while some use automatic transmission fluid, made from synthetic base oil.[6][7]

Use of the wrong type of fluid can lead to failure of the power steering pump.[8]

Safety

Because industrial hydraulic systems operate at hundreds to thousands of PSI and temperatures reaching hundreds of degrees Celsius, severe injuries and death can result from component failures and care must always be taken when performing maintenance on hydraulic systems.

Fire resistance is a property available with specialized fluids. Water-gycol and polyol-ester are some of these specialized fluids that contain excellent thermal and hydrolitic properties, which aid in fire resistance.[9]

Trade names

Some of the trade names for hydraulic fluids include Arnica, Mobil DTE, Tellus, Durad, Fyrquel, Houghto-Safe, Hydraunycoil, Crown Hydraulic Oils, Lubritherm Enviro-Safe, Pydraul, Quintolubric, Reofos, Reolube, Valvoline Ultramax, Gandhar and Skydrol.

Aircraft hydraulic systems

As aircraft performance increased in mid-20th century, the amount of force required to operate mechanical flight controls became excessive, and hydraulic systems were introduced to reduce pilot effort. The hydraulic actuators are controlled by valves; these in turn are operated directly by input from the aircrew (hydro-mechanical) or by computers obeying control laws (fly by wire).

Hydraulic power is used for other purposes. It can be stored in accumulators to start an auxiliary power unit (APU) for self-starting the aircraft's main engines. Many aircraft equipped with the M61 family of cannon use hydraulic power to drive the gun system, permitting reliable high rates of fire.

The hydraulic power itself comes from pumps driven by the engines directly, or by electrically driven pumps. In modern commercial aircraft these are electrically driven pumps; should all the engines fail in flight the pilot will deploy a propeller-driven electric generator called a Ram Air Turbine (RAT) which is concealed under the fuselage.[10] This provides electrical power for the hydraulic pumps and control systems as power is no longer available from the engines. In that system and others electric pumps can provide both redundancy and the means of operating hydraulic systems without the engines operating, which can be very useful during maintenance.

Specifications

Mineral Oil Base:

Synthetic Hydrocarbon Base: These synthetic fluids are compatible with mineral base hydraulic fluids and were developed to address the low flash point draw back of mineral based hydraulic fluids.[13]

Phosphate-ester Base:

Contamination

Special, stringent care is required when handling aircraft hydraulic fluid as it is critical to flight safety that it stay free from contamination. It is also necessary to strictly adhere to authorized references when servicing or repairing any aircraft system. Samples from aircraft hydraulic systems are taken during heavy aircraft maintenance checks (primarily C and D checks) to check contamination.

See also

References

External links

This article is issued from Wikipedia - version of the Sunday, December 20, 2015. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.