History of the M1 Abrams

The M1 Abrams has been in service since 1980. Ever since about 200 crewman have been KIA. In Recent Years the M1 Abrams has lost some of its fighting ability. It is the current Main Battle Tank of the U.S.A

Development

An XM1 Abrams, during a demonstration at Fort Knox, Kentucky in 1979.

The first attempt to replace the aging M60 Patton was the MBT-70, developed in partnership with West Germany in the 1960s. The MBT-70 was very ambitious, and had various ideas that ultimately proved unsuccessful. As a result of the imminent failure of this project, the U.S. Army introduced the XM803. This succeeded only in producing an expensive system with capabilities similar to the M60.^[1]

Congress canceled the MBT-70 in November and XM803 December 1971, and redistributed the funds to the new XM815 later renamed the XM1 Abrams after General Creighton Abrams, former Army Chief of Staff and Commander of US military forces in Vietnam. Prototypes were delivered in 1976 by Chrysler Defense and General Motors armed with the license-built version of the 105 mm Royal Ordnance L7 gun along with a Leopard 2. The Leopard 2 was deemed right away as being too expensive and the General Motors design was labeled as inferior and thus the Chrysler Defense design was selected for development as the M1. In 1979, General Dynamics Land Systems Division purchased Chrysler Defense.

3273 M1 Abrams were produced 1979-85 and first entered US Army service in 1980. It was armed with the license-built version of the 105 mm Royal Ordnance L7 gun. An improved model called the M1IP was produced briefly in 1984 and contained small upgrades. The M1IP models were used in the Canadian Army Trophy NATO tank gunnery competition in 1985 and 1987.

About 6000 M1A1 Abrams were produced from 1986–92 and featured the M256 120 mm smoothbore cannon developed by Rheinmetall AG of Germany for the Leopard 2, improved armor, and a CBRN protection system.

Persian Gulf War

Abrams move out on a mission during the Persian Gulf War. A Bradley IFV and logistics convoy can be seen in the background.

M1A1 lost to friendly fire during Persian Gulf War.

As the Abrams entered service in the 1980s, they would operate alongside M60A3 within the United States military, and with other NATO tanks in numerous Cold War exercises. These exercises usually took place in Western Europe, especially West Germany, but also in some other countries like South Korea. During such training, Abrams crews honed their skills for use against the men and equipment of the Soviet Union. However, by 1991 the USSR had collapsed and the Abrams would have its trial by fire in the Middle East.

The Abrams remained untested in combat until the Persian Gulf War in 1991. The M1A1 was superior to Iraq's Soviet-era T-55 and T-62 tanks, as well as Iraqi assembled Russian T-72s, and locally produced copies (Asad Babil tank). The T-72s like most Soviet export designs lacked night vision systems and then-modern rangefinders, though they did have some night fighting tanks with older active infrared systems or floodlights—just not the latest starlight scopes and passive infrared scopes as on the Abrams. Only 23 M1A1s were taken out of service in the Persian Gulf^[2] and one of these losses resulted in a crew death from Iraqi fire. Some others took minor combat damage, with little effect on their operational readiness. Very few Abrams tanks were hit by enemy fire, and there was only one fatality, along with a handful of woundings as a result.

The M1A1 was capable of making kills at ranges in excess of 2,500 meters (8,200 ft). This range was crucial in combat against tanks of Soviet design in Desert Storm, as the effective range of the main gun in the Soviet/Iraqi tanks was less than 2,000 meters (6,600 ft) (Iraqi tanks could not fire anti-tank missiles like their Russian counterparts). This meant Abrams tanks could hit Iraqi tanks before the enemy got in range—a decisive advantage in this kind of combat. In friendly fire incidents, the front armor and fore side turret armor survived direct APFSDS hits from other M1A1s. This was not the case for the side armor of the hull and the rear armor of the turret, as both areas were penetrated at least in two occasions by friendly DU ammunition during the Battle of Norfolk.^[3]

No Abrams tank has ever been destroyed as a result of fire from enemy tanks, although several have certainly taken some damage which required extensive repair. There is at least one account, reported in the following Persian Gulf War's US Official Assessment (scan), of an Abrams being damaged by three kinetic energy piercing rounds. The DoD report indicates that witnesses in the field claimed it was hit by a T-72 Asad Babil. The KE rounds were unable to fully penetrate and stuck in the armor, but because of the external damage it was sent to a maintenance depot. This is the only verified case of an M1A1 put out of action by an Iraqi MBT.^[4]

Six other M1A1s were allegedly hit by 125 mm tank fire according to the Persian Gulf war official report, but the impacts were largely ineffectual. This can be attributed to the fact that Iraqi T-72s were firing inferior ammunition, a generation behind that used by the Russian army at the time. ^[5]

On the night of February 26, 1991, four Abrams were disabled in a suspected friendly fire incident by Hellfire missiles fired from AH-64 Apache attack helicopters, with the result of some crew members wounded in action.^[6] The tanks were part of TF 1-37,^[7] attacking a large section of Medina Republican Guard Division, their numbers being B-23, C-12, D-24 and C-66. Abrams C-12 was definitively hit and penetrated by a friendly DU shot^[8] and there is some evidence that another Iraqi T-72 may have scored a single hit on B-23, besides the alleged Hellfire strike. ^{[N 1]}

Tanks D-24 and C-66 took some casualties, ^[9] but only B-23 became a permanent loss. The DoD's damage assessments state that B-23 was the only M1 with signs of a Hellfire missile found nearby.

Also during the Persian Gulf war, three Abrams of the US 24th Infantry Division were left behind the enemy lines after a swift attack on Talil airfield, south of Nasiriyah, on February 27. One of them was hit by enemy fire, the two other embedded in mud. The tanks were destroyed by U.S. forces in order to prevent any trophy-claim by the Iraqi Army.^[10]

Interwar upgrades

Following lessons learned in Desert Storm, the Abrams and many other US combat vehicles used in the conflict were fitted with Combat Identification Panels to reduce friendly fire incidents. These were fitted on the sides and rear of the turret, with flat panels equipped with a four-cornered 'box' image on either side of the turret front (these can be seen in the below image, similar flat panels also being employed on British Challenger 2 tanks serving in the conflict).

In addition to the Abrams' already heavy armament, some crews were also issued M136 AT4 shoulder-fired anti-tank weapons under the assumption that they might have to engage heavy armor in tight urban areas where the main gun couldn't be brought to bear. Some Abrams were also fitted with a secondary storage bin on the back of the existing bustle rack on the rear of the turret referred to as a bustle rack extension to enable the crew to carry more supplies and personal belongings.

The M1A2 is a further improvement of the M1A1 with a commander's independent thermal viewer and weapon station, position navigation equipment, digital data bus and a radio interface unit. The M1A2 SEP (System Enhancement Package) added digital maps, FBCB2 (Force XXI Battlefield Command Brigade and Below) capabilities, and an improved cooling system to maintain crew compartment temperature with the addition of multiple computer systems to the M1A2 tank.

Further upgrades include depleted uranium armor for all variants, a system overhaul that returns all A1s to like-new condition (M1A1 AIM), a digital enhancement package for the A1 (M1A1D), a commonality program to standardize parts between the U.S. Army and the Marine Corps (M1A1HC) and an electronic upgrade for the A2 (M1A2 SEP).

During Operations Desert Shield and Desert Storm and for Bosnia, some M1A1s were modified with armor upgrades. The M1 can be equipped with mine plow and mine roller attachments if needed. The M1 chassis also serves as a basis for the Grizzly combat engineering vehicle and the M104 Wolverine heavy assault bridge.

Over 8,800 M1 and M1A1 tanks have been produced at a cost of US$2.35–$4.30 million per unit, depending on the variant.

Iraq War

M1A1 Abrams pose for a photo under the "Hands of Victory" in Ceremony Square, Baghdad, Iraq.

US Marine Corps M1A1 on a live fire exercise in Iraq, 2003

A destroyed USMC M1A1 Abrams rests in front of a Fedayeen camp just outside Jaman Al Juburi, Iraq in April 2003.

M1A1 conducts reconnaissance in Iraq in September 2004.

Further combat was seen during 2003 when US forces invaded Iraq and deposed the Iraqi leader Saddam Hussein. As of March 2005, approximately 80 Abrams tanks shipped back to the United States for repair due to fire from enemy attacks.^[27] Nevertheless, the campaign saw very similar performance from the tank with no Abrams crew member being lost to hostile fire during the invasion of Iraq, although several tank crew members were later killed by snipers and roadside bombs during the occupation that followed. Abandoned Abrams were purposely destroyed by friendly fire to prevent recovery of vehicle or technology. Damages by 25 mm AP-DU, anti-armor RPG fire and 12.7 mm rounds was encountered. But on no occasion did anti-tank guided weapons or anti-tank mines strike the US MBTs.^[28]

During the Battle of Najaf on March 25, two Abrams were struck by an unidentified weapon and knocked out. Their ammunition stores ignited, but both crews escaped without injury. ^{[29] [30]} Another Abrams was disabled near Karbala after an RPG warhead penetrated the rear engine compartment. ^{[31] [32]} There were more losses during the Battle of Baghdad. On April 4, two Abrams were destroyed by anti-aircraft guns,^{[33] [34]} while on April 5, another was hit by a recoilless rifle and set aflame. After repeated attempts to extinguish the fire, the decision was made to destroy or remove any sensitive equipment. Oil and .50 caliber rounds were scattered in the interior, the ammunition doors were opened and several thermite grenades ignited inside. Another M1 then fired a HEAT round in order to ensure the destruction of the disabled tank. The Abrams was completely disabled but still intact. ^[35] Later, the Air Force bombed the tank to destroy it in place, and the Iraqi Information Ministry claimed credit for destroying it.

The most lopsided achievement of the M1A2s was the destruction of seven Lion of Babylon tanks in a point-blank skirmish (less than 50 yards (46 m)) near Mahmudiyah on April 3, with no losses for the American side.^[36] However, on October 29, 2003, two soldiers were killed and a third wounded when their tank was disabled by an anti-tank mine, which was combined with other explosives (up to 250 kg, including several 155 mm rounds) to increase its effect. ^{[N 2]} The massive explosion beneath the tank knocked off the turret. This marked the first time deaths resulted from a hostile-fire assault on the M1 tank from enemy forces.

During the major combat operations in Iraq, Abrams crew members were lost when one tank of the US Army's 3rd Infantry Division, and US Marine Corps troops, drove onto a bridge. The bridge collapsed, dropping the tank into the Euphrates River,^[37] where four Marines drowned.

On November 27, 2004, an Abrams tank was badly damaged from the detonation of an extremely powerful improvised explosive device (IED). The IED consisted of three 155 mm shells (containing 34.5 kg of explosives) that detonated next to the tank. The tank's driver received lethal injuries from shrapnel. The other three crew members were able to escape.

On December 25, 2005, another U.S. Army M1A1 was disabled by an explosively formed penetrator IED. The IED penetrated through a road wheel, and hit the fuel tank, which left the tank burning near central Baghdad. One crew member, specialist Sergio Gudino, died in the attack.

On June 4, 2006, two of the four soldiers in an Abrams crew were killed in Baghdad when an IED detonated near their M1A2.

Some Abrams were disabled by Iraqi infantrymen in ambushes employing short-range antitank rockets, such as the Russian RPG-7, during the 2003 invasion. Although the RPG-7 is unable to penetrate the front and sides, the rear and top are vulnerable to this weapon. Frequently the rockets were fired at the tank tracks. Another was put out of action in an incident when fuel stowed in an external rack was struck by heavy machine gun rounds. This started a fire that spread to the engine.^[28][38]

There have also been a number of Abrams crewmen killed by sniper fire during times when they were exposed through the turret hatches of their tanks. Some of these attacks were filmed by insurgents for propaganda purposes and spread via the Internet. One of these videos shows a large IED detonating beneath an Abrams and nearly flipping the vehicle, though it landed back on its treads and appeared to have suffered no serious damage as it was still mobile and traversing the turret following the attack. In another video, this one filmed by U.S. Army soldiers, an Abrams was attempting to crush an abandoned vehicle by running over it when a hidden IED inside the vehicle detonated directly beneath the tank, the Abrams again seeming to suffer no significant damage.^[39]

Iraqi usage

It was reported that 28 Iraqi Army Abrams had been damaged in fighting with militants, five of them suffering full armor penetration when hit by ATGMs, in the period between 1 January and the end of May 2014; some were destroyed or damaged by militants placing explosive charges on or in the vehicles, highlighting the lack of adequate infantry support provided by Iraqi soldiers.^[40] In mid-2014, Iraqi Army Abrams tanks saw action when the Islamic State of Iraq and the Levant launched the June 2014 Northern Iraq offensive. Some Iraqi Army M1A1M tanks were destroyed in fighting against ISIL forces while an unknown number were captured intact. At least one ISIL-controlled M1A1M Abrams was reportedly used in the capture of the Mosul Dam in early August 2014. The Abrams suffered its first heavy losses at the hands of ISIL fighters against Iraqi-operated tanks through planted explosives, anti-tank missiles like the Kornet, and captured tanks later being destroyed by American airstrikes. The chief cause of these losses was the poor training of Iraqi tank operators and lack of infantry coordination.^[41] About one-third of the 140 Abrams tanks delivered to the Iraqi Army had been captured by ISIL. By December 2014, the Iraqi Army only had about 40 operational Abrams left. That month, the U.S. State Department approved the sale of another 175 Abrams to Iraq.^[42] The tanks may be fitted with additional protection features to defend against ISIL mine, roadside bomb, and other attacks including belly armor, reactive armor, 360-degree night vision sensors, mine-clearing blades and rollers, and a wide-area spotlight-equipped remotely operated gun mount. If approved by Congress and funded by the Iraqi government, the improvements could be made within 18 months.^[43] By late 2015, some Iraqi Abrams tanks that had been dropped off at repair facilities were re-equipped with Russian heavy machine guns firing Iranian-manufactured ammunition, which may violate sales agreements prohibiting material usage by Shiite militias and the unsanctioned addition of foreign weapons.^[44]

Afghanistan

Operating tanks in Afghanistan can be difficult due to the terrain, although Canada and Denmark have deployed tanks to Afghanistan that have been specifically upgraded to fight in the tough Afghan environment. The U.S. sent 16 M1A1 Abrams tanks and 115 Marines to southern Afghanistan to support operations in the Helmand and Kandahar provinces in late 2010.^[45][46]

Future

The tracked M8 Armored Gun System was conceived as a possible supplement for the Abrams in U.S. service for low-intensity conflict in the early 90's. Prototypes were made but the program was canceled. The 8-wheeled M1128 Mobile Gun System was designed to supplement the Abrams in U.S. service for low-intensity conflict. It has been introduced into service and, though mobile, it has proven to be quite vulnerable.

The U.S. Army's Future Combat Systems' XM1202 Mounted Combat System was to replace the Abrams in U.S. service and was in late stages of development when funding for the program was cut from the DoD's budget.

In September 2009, the Army Times^[47] and Marine Corps Times^[48] published reports that US Army researchers have begun the process of designing a version of the Abrams that will carry the M1A3 label. According to the reports, the Army is seeking to reduce the weight of the vehicle to approximately 60 tons from its current operational weight of roughly 75 tons. Additionally, the M1A3 may incorporate a new generation of advanced networking capabilities and enhanced armor protection. Other improvements are to include a lighter 120 mm gun, added road wheels with improved suspension, a more durable track, lighter armor, long-range precision armaments, and infrared camera and laser detectors. A new internal computer system is also planned, with current cabling replaced by fiber-optic cables that can reduce weight by two tons.^[49] The Army currently aims to build prototypes by 2014 and to begin to field the first combat-ready M1A3s by 2017.

The developing Ground Combat Vehicle seeks to generate a family of combat vehicles that could permanently replace the M1 as well as many other U.S. army vehicles. The Army anticipates that the Abrams may remain in service until 2050.

Production

The military planned to close the M1 Abrams factory in Ohio from 2013 to 2016 to save over US$1 billion. In 2017 the plant would reopen to upgrade existing tanks. The downside to the three-year plant closing is the loss of the skilled human capital required to build the M1. These types of job skills must be learned on the job as the building is too unique to offer any type of educational program in a trade school environment.^[50]

By August 2013, Congress had allocated $181 million for buying parts and upgrading Abrams systems to mitigate industrial base risks and sustain development and production capability. Congress and General Dynamics were criticized for redirecting money to keep production lines open and accused of "forcing the Army to buy tanks it didn't need." General Dynamics asserted that a four-year shutdown would cost $1.1–1.6 billion to reopen the line, depending on the length of the shutdown, whether machinery would be kept operating, and whether the plant's components would be completely removed. They contended that the move was to upgrade Army National Guard units to expand a "pure fleet" and maintain production of identified "irreplaceable" subcomponents; a prolonged shutdown could cause their makers to lose their ability to produce them and foreign tank sales were not guaranteed to keep production lines open. Even though money is being spent to protect the industrial base, some feel those strategic choices should not be made by members of Congress, especially those with the facilities in their district. There is still risk of production gaps even with production extended through 2015; with funds awarded before recapitalization is needed, budgetary pressures may push planned new upgrades for the Abrams from 2017 to 2019.^[51] In December 2014, Congress again allocated $120 million, against the wishes of the Army, for Abrams upgrades including improving gas mileage by integrating an auxiliary power unit to decrease idle time fuel consumption and upgrading the tank's sights and sensors.^[52][53]

Notes

References