Ford Windsor engine

Ford Windsor[1]
Overview
Manufacturer Ford Motor Company
Also called Small Block Ford
Production July 1961–December 2000
Combustion chamber
Configuration 90° OHV small-block V8, 4.380" bore spacing
Displacement 221 cu in (3.6 L)
255 cu in (4.2 L)
260 cu in (4.3 L)
289 cu in (4.7 L)
302 cu in (5.0 L)
335 cu in (5.5 L)
351 cu in (5.8 L)
Cylinder bore 4.000" (289, 302, 351W)
3.900" (335) 3.800" (260)
3.680" (255) 3.500" (221)
Piston stroke 3.510" (335) 3.500" (351W)
3.000" (302 & 255)
2.870" (221, 260, 289)
Cylinder block alloy Cast iron (stock)

Deck Height:
9.480" ('69-'70 351W )
9.503" ('71-'96 351W)
8.201"-.210" (BOSS 302)
8.206" (221, 260, 289, 302)
Cylinder head alloy Cast iron (stock)
A356-T6 (aftermarket)
Valvetrain Cast iron cam, Flat tappet ('62-'84 302, '69-'93 351W)
Steel roller cam & lifters ('85-'01 302, '94-'96 351W)
Compression ratio 9.0:1 ('87-'92 302)
Combustion
Supercharger Naturally aspirated (stock)
Fuel system Carbureted (1962-1985)
EFI (1986-2001)
Oil system Wet sump (stock)
Dry Sump (aftermarket)
Cooling system Jacketed block (stock)
Dimensions
Length 27.50" (302, 351W) [Note 1]
Width 21.00" (351W)
18.75" (302)
Height 23.75" (351W) [Note 2]
20.75" (302)
Chronology
Predecessor Ford Y-block engine
Successor Ford Modular engine

The 'Fairlane V8' engine, as it was known at Ford, went into production in July 1961 ready for installation into the all new 1962 model-year 'Intermediate' Ford Fairlane and Mercury Meteor cars which started to be released to the public in late November 1961. This all new engine began in May 1960 when chief engineer of the Engine & Foundry Division of the Ford Motor Company, Bill Innes, selected 39 year old section supervisor, George Stirrat, to lead a team of nine engineers to design a compact, light-weight V8 engine of 220-225 cu in, which had to be in production during July of the following year. This target was met with the whole process taking just 13 months from start to finish - a remarkable achievement in automotive engineering terms. This was only possible because the 221ci engine was designed to be machined using the existing Ford Y-Block V8 machine tooling. The production of an engine didn't just stop at Ford, engines were phased in and phased out with much over-lap. This way, if anything went wrong with the new engine, the old engine was still in production and could be increased to cover any deficit. This of course couldn't have applied to the 221ci because of its small dimensions so it had to be right. The Ford Y-Block was in fact going to be phased out at some time in the near future but the new engine wasn't at that time the intended replacement - just a new engine. One line of Ford Y-Block production at the Cleveland Engine Plant however was stopped in 1961 and converted to 221ci engine production. The Small Block Ford family of engines evolved significantly during its 39-year history through technological, performance, and reliability enhancements. Engine displacement also increased from 221 cu in (3.6 L) up to 351 cu in (5.8 L) over the years in several stages namely 221ci (1961-1963), 260ci (1962-1964), 289ci (1963-1968), 302ci (1968-2000), 351ciW (1969-1996), 335ci (1970-1996 in Mexico) and 255ci/4.2L (1980-1982).

The 221ci, 260ci, 289ci-2V, 289ci-4V and the HP-289ci-4V, were manufacturered at Ford's Cleveland Engine Plant Number One/CEP1 (July 1961- June 1967). The production of 289s started at the Windsor Engine Plant Number One/WEP1 in 1966 and continued through to August 1968 while the Cuautitlan Engine Plant in Mexico started to make 260ci and 289ci engines in 1965. The 302ci variant was introduced for the 1968 car model year (production started July 1967) and all three engine plants started to make them, with the Windsor Engine Plant only, continuing to make the 289ci until August 1968 - a cheaper engine than the 302ci and a way of using up all of the existing 289 parts. The Windsor Engine Plant made the 302 for one year before re-tooling to start making the George Stirrat/Philip Martel designed 'tall deck' 351ci version of the small block engine for the 1969 car model year. The Cleveland Engine Plant Number One made the 302ci right through to 2000 having added a second line in 1978 in an effort to keep up with demand. The Windsor Engine Plant Number Two/WEP2 made all of the 255ci/4.2L engines 1980-1982 and then switched over to 302ci/5.0L production in 1983 and continued until 1996. The Cuautitlan Engine Plant made approximately 1 million 260ci, 289ci, 302ci, 335ci (based on the 351ciW) and 351ciW engines 1965-1996.

The 335 Series, 351ci "Cleveland" V8 or 351ciC, introduced in 1970, was intended as a USA only option - a higher specification small block engine for US customers only. This small block variant was over-seen by chief engineer Bill Gay himself although the canted valve cylinder head arrangement was an engine engineering engineer, Joe Macura recommendation. The 'W' for Windsor and 'C' for Cleveland being the means by which Ford first differentiated between their two 351ci engine variants for 1970 car model year vehicles. The Cleveland V8 was phased out at the end of 1974 due to a basic lack of demand after about 4 million had been made, it being more expensive than the 351ciW. The term 'Windsor' has therefore been extrapolated over the years by the press and general public to include the whole engine series - Ford too now quotes the term Windsor for this series of engines. Using the term 'Windsor' to describe the whole series of engines is therefore very acceptable as is knowing how it occurred. It is Fords most numerously produced V8 with approximately 35,000,000 units having been made.

For the 1991 car model year, Ford began phasing in their new Jim Clarke design team led 4.6/5.4 L Modular V8 engine which was to replace the small block Windsor - it was regarded as old technology by this point even if good technology. In 1996, Ford replaced the 5.0 L (302 cu in) pushrod Windsor V8 with the Modular 4.6 L in the Mustang. Its use continued until 1997 in the F-150 pickup truck, and until 2001 in the Explorer SUV and 2002 by Ford Australia in their Falcon and Fairlane cars but production of the 302ci/5.0L had stopped at the end of December 2000 and the engines used came from 'build ahead stocks'.

From the mid-1970s through the 1990s, the 'Windsor' engine was also marinized for use in smaller recreational boats. As of 2014, Windsor engines, including the 5.8 L (351 cu in) and 5.0L 302, were still being manufactured from Ford's massive 'build ahead stocks' inventory; available as complete crate motors from Ford Racing and Performance Parts.[2] Ford Power Products, a small division of the Ford Motor Company, supplied quite a range of 5.0L and 5.8L marine and industrial/stationary engines over the years. For example: 5.0L stationary engines for pumping oil or water and electricity generation; commercial air compressors where the right-hand cylinder head had been removed and converted to air compressing, 5.0L and 5.8L were even available for home-built aircraft - engines certified, installed backwards in planes, open exhaust, back-fire protection in the carburetor. 5.0L in Brazil converted to run on 100% alcohol - low compression ratio of 7.0:1.

Overview

The small block Ford engine uses a 'thin-wall' (a process developed by Harold Grant of the Foundry Division) cast iron block with a separate timing chain cover, made from aluminum. This feature differentiates it from later Cleveland, or 335-Series engines, that use an integrated timing cover, cast in the block. All Windsors use 2-valve per cylinder heads regardless of whether they are "2V", "4V", or fuel-injected models. The 2V & 4V designations referred to the number of venturi (or barrels) in the carburetor, not valves per cylinder. The valves are in-line and use straight 6-bolt valve covers. Another simple differentiation between the Small Block and "335" Cleveland series is the location of the radiator hose — the Windsor routed coolant through the intake manifold, with the hose protruding horizontally, while the Cleveland had the radiator hose connecting vertically to the engine block. The Cleveland and later "Modified" engines used a canted valve design, allowing for larger valves within the same 4-inch bore. Something worth noting was the fact that the Ford Engineers designed the Cleveland heads with the same bore spacing and head bolt configuration making it possible (with some light machine work) to bolt Cleveland heads to the Windsor block and in 1969 they did just that creating the Boss 302 Mustang.

The oil routing in the engine block is unique in that a third passage is drilled parallel to the tappet passages. This passage ensures that oil reaches the main and cam bearings before the tappets, reducing the likelihood of lubricant starvation of the bearings (unlike the 351 Cleveland and the 385 series). The tappets are fed from an inverted 'V' passage cast in the rear under the intake manifold that connects with this passage and is sealed with a steel cap. The third oil passage is visible from the rear of the block with the transmission components removed. It is under and slightly right of the right bank tappet passage. The tappets on the left bank are the farthest from the oil pump and are last to be pressurized by oil upon a dry start. This gives an impression that there is insufficient lubrication, but this is normal and the noise ceases after several seconds of operation. This series of Ford V8 has a simply excellent oiling system, faultless in fact.

With the exception of the 289 HiPo, Boss 302 and 351W, all connecting rods use the same 5/16-inch diameter bolts. The rod forgings had undergone some changes throughout its history. The 221, 260 and early 289 (C2OZ-A and C3AE-D) rods used an oil squirt hole to lubricate the piston pin and rings. The oil squirt hole was discontinued in 1964. The same forging continued to be used up to 1967 and all were the same length (5.155 in). The 302 used a shorter beam (C8OE-A 5.090 in) but used the same cap up to 1970. In 1971 the cap design was changed from the original 'twin rib' to a cheaper to make 'strap' type (D1OE-A). This was changed back to the 'twin rib' design in 1988 due to fatigue failures from increased power output of fuel injection and continued until the end of production. The 289 HiPo and Boss 302 were the same length (5.155 in) and in fact nearly the same forging except for across the connecting rod part-line which was made slightly wider, a different cap forging, 3/8 in bolts and was machined with slightly wider bolt centres. The former used square head bolts and square cut and the latter were spot faced for 'football head' type bolts.

221

The first engine of this family, introduced for the 1962 model year as an option on the Ford Fairlane and Mercury Meteor, had a displacement of 221 cu in (3.6 L), from a 3.5 in (89 mm) bore and 2.87 in (72.9 mm) stroke, with wedge combustion chambers for excellent breathing. An advanced, compact, thinwall-casting design, it was 24 in wide, 29 in long, and 27.5 in tall (610 mm × 737 mm × 699 mm). It weighed only 470 lb (210 kg) dry despite its cast iron construction, making it one of the lightest and most compact V8 engines of its class. The reason for making the engine 221ci was nostalgia.

Note that all of the July 1961 through August 1964 221-260-289 engines used a five-bolt bell housing, with all 221 and 260 being of this configuration but the 289 changed to the six bolt arrangement at this time - the change was made due to transmission utilization issues ie the need for larger diameter clutches for example. The block mount pads and the cylinder wall contour of the 221 and 260 engines changed in January-February 1963 with the introduction of the 289 variant – all 221 and 260 engine blocks up to this time featured 'corrugated wall' construction with two freeze plugs on the side of each block and engine mount hole pitch distances of 6 inch. All three block variants from this point on featured the 'straight wall' method of construction, three freeze plugs and an engine mount hole pitch distance of seven inches. The "corrugated wall" method of block construction had caused cleaning difficulties in the foundry from day one and a change was phased in.

In stock form it used a two-barrel carburetor and a compression ratio of 8.7:1, allowing the use of regular (rather than premium) gasoline. Valve diameters were 1.59 in (40.4 mm) (intake) and 1.388 in (35.3 mm) (exhaust). Rated power and torque (SAE gross) were 145 hp (108 kW) at 4,400 rpm and 216 lb·ft (293 N·m) at 2,200 rpm.

The 221 was phased out in April of 1963 due to a lack of demand after approximately 270,000 had been produced. Ford engineers knew straight away that the engine wasn't quite powerful enough for these cars equipped with the two speed automatic transmission which led to the introduction of a larger cu in version.

260

The second version of the Fairlane V8, introduced during the middle of the 1962 model year (March 1962), had a larger bore of 3.80 in (96.5 mm), increasing displacement to 260 cu in (4.3 L). Compression ratio was raised fractionally to 8.8:1. The engine was slightly heavier than the 221, at 482 lb (219 kg). Rated power (still SAE gross) rose to 164 hp (122 kW) @ 4400 rpm, with a peak torque of 258 lb·ft (350 N·m) @ 2200 rpm.

For the 1962 and 1963 car model years, the valve diameters remained the same as the 221, but for the 1964 car model year they were enlarged to 1.67 in (42.4 mm) (intake) and 1.45 in (36.8 mm) (exhaust) – this was an economy measure so that both 260 and 289 engines would use the same valves. Rated power was not changed.

In 1963 the 260 became the base engine on full-size Ford sedans. Later in the model year its availability was expanded to the Ford Falcon and Mercury Comet. The early "1964½" Ford Mustang also offered the 260, although it was dropped at the end of the 1964 car model year. The 1964–1966 Sunbeam Tiger Mk I used the 260ci. The 1967 Sunbeam Tiger Mk II used the 289 CID V8 (see 289) when stocks of the 260 ran out.

The special rally version of the Falcon and Comet and early AC Cobra sports cars used a high-performance version of the 260ci with higher compression, hotter camshaft timing, and a four-barrel carburetor. This engine was rated (SAE gross) 260 hp (194 kW) @ 5800 rpm and 269 lb·ft (365 N·m) @ 4800 rpm. This engine was termed the HP-260 by Ford and was specifically made for Carroll Shelby – approximately 100 were made.

Ford dropped the 260 after the 1964 model year with approximately 600,000 having been made.

289

289 Windsor V8 in a 1965 Ford Mustang

The 289 cu in (4.7 L) was also introduced in April 1963. Bore was expanded to 4.00 in (101.6 mm), becoming the standard bore for most 'Windsor' engines. The 289 weighed 506 lb (230 kg).

In 1963 the 289 was available in two forms. The base version came with a two-barrel carburetor and 8.7:1 compression; it was rated at 195 hp (145 kW) (SAE gross) at 4,400 rpm and 258 lb·ft (350 N·m) at 2,200 rpm. The two-barrel 289 replaced the 260 as the base V8 for full-sized Fords. As a performance option, the "HiPo" or "K-code" engine was offered; the K-code is discussed more below. In 1963 it was available only in the Fairlane.

In 1964, an intermediate performance version of the engine was introduced with a four-barrel carburetor and 9.0:1 compression, rated at 210 hp (157 kW) at 4,400 rpm and 300 lb·ft (407 N·m) at 2,800 rpm. The engine was an option on both the initial 1964 1/2 Ford Mustang and the Mercury Comet. The engine was known as the "D-code" from the letter code used to identify the engine in the VIN.[3][4] The D-code engine is relatively rare, as it was only offered as an optional engine in the latter half of the 1964 model year.

Both 1963 and 1964 versions had a five-bolt bell housing pattern that was different from later six-bolt units (Mustangs switched bolt patterns around August 3, 1964). The engines switched from a generator to an alternator in the latter part of the 1964 model year.

For 1965 the compression ratio of the base 289 was raised to 9.3:1, increasing power and torque to 200 hp (149 kW) at 4,400 rpm and 282 lb·ft (382 N·m) at 2,400 rpm. The four-barrel version was increased to 10.0:1 compression, and was rated at 225 hp (168 kW) at 4,800 rpm and 305 lb·ft (414 N·m) at 3,200 rpm. The HiPo engine specifications were not changed.

Engine specifications were unchanged for 1966 and 1967. In 1968 the four-barrel 225 hp (168 kW) engine was dropped, leaving only the two-barrel – now reduced back to 195 hp (145 kW). The HiPo engine was also dropped, making room for the new for 1968 302 V8. 1968 was the last year of production for the 289 in the U.S.

The 289-4V was also the engine for the first Australian Ford Falcon GT, the XR Falcon GT. Approximately 3,500,000 289ci-2V and 289ci-4V engines were made at CEP1 1963-1967 and 800,000 289ci-2V at WEP1.

289 "HiPo" (K-code)

Ford 289 K-code engine in a Shelby GT 350. Note that the radiator hose connects to the intake manifold, a telltale Windsor feature.

A high-performance version of the 289 engine was introduced late in the 1963 model year as a special order for Ford Fairlanes. The engine is informally known as the "HiPo" or the K-code (after the engine letter used in the VIN of cars so equipped). Oddly, this engine was introduced in 1963 as the only 289 engine available in the intermediate Fairlanes. Lesser powered cars had the 260 engine in that year. Starting in June 1964, it became an option for the Mustang. NOTE: K-code Mercury Comets were the 210 HP 4 bbl carb engine not the same High Performance engine as the K-code Fords.

The HiPo engine was engineered to increase performance and high-RPM reliability over standard 289 fare. It had solid lifters with hotter cam timing; 10.5:1 compression; a dual point, centrifugal advance distributor; smaller combustion chamber heads with cast spring cups and screw-in studs; low restriction exhaust manifolds; and a bigger, manual choke 595 CFM carburetor (std 289-4V was 480 CFM). The water pump, fuel pump, and alternator/generator pulley were altered; fewer vanes, extra spring, and larger diameter respectively; to help handle the higher engine speeds. Even the HiPo’s fan was unique. Bottom end improvements included; a flaw free selected standard block, thicker main bearing caps and crankshaft damper/balancer, larger diameter rod bolts, a crankshaft made from 80% "nodular iron" as opposed to the regular items 40%, all were checked for correct 'nodularity' by polishing an area of the rear counterweight and comparing that surface using a magnification arrangement against a picture datum, increased crankshaft counterweighting to compensate for the heavier connecting rod big ends, the increased external counterweighting at the front was split between the crankshaft damper and a supplementary counterweight place adjacent to the front main bearing journal (all designed to reduce the 'bending moment' in the crankshaft at high-rpm), all for high-rpm reliability. The HiPo carried SAE gross ratings of 271 hp (202 kW) at 6,000 rpm and 312 lb·ft (423 N·m) at 3,400 rpm. Approximately 25,000 were manufactured at CEP1 between March 1963-June 1967.

The HiPo engine was used in modified form by Carroll Shelby for the 1965–1967 Shelby GT350, raising rated power to 306 hp (228 kW) at 6,000 rpm through use of special exhaust headers, an aluminum intake manifold, and a larger carburetor. The Shelby engine also had a larger oil pan with baffles to reduce oil starvation in hard cornering. Shelby also replaced the internal front press-in oil gallery plugs with a screw-in type plug to reduce chances of failure.

From 1966 to 1968, Shelby offered an optional Paxton supercharger for the 289, raising its power (on Shelby GT350s) to around 390 hp (291 kW).

The K-code HiPo engine was an expensive option and its popularity was greatly diminished after the 390 and 428 big-block engines became available in the Mustang and Fairlane lines, which offered similar power (at the expense of greater weight) for far less cost.

302

302 "4V" V8 in a 1968 Mercury Cougar
302 "Hi-Po" V8 in a 1967 Ford Mustang
Note that there was also a 302 cubic inch 335 Series engine "302 Cleveland" produced by Ford Australia for the Australian market.

By 1967 the Ford GT40 MKII and GT40 MKIV had dominated the Le Mans 24Hr Race for two consecutive years, using various versions of the Ford big block engine. In an attempt to reduce the high speeds in 1968 (some say to equalize the competition), the organisers of this race capped the engine capacity. Ford consequently returned to the MKI GT40 (originally using the Windsor 289ci) but had now increased its capacity to meet the new rules. Since Ford had ruled that the GT40 engines must have a direct link back to its production cars, the 302ci was adopted in domestic manufacturing. [5]

So in 1968 the small block Ford was stroked to 3.0 in (76.2 mm), giving a total displacement of 302 CI (4,942 cc). The connecting rods were shortened to allow the use of the same pistons as the 289. It replaced the 289 early in the 1968 model year.

The most common form of this engine used a two-barrel carburetor, initially with 9.5:1 compression. It had hydraulic lifters and valves of 1.773 in (45 mm) (intake) and 1.442 in (36.6 mm) (exhaust), and was rated (SAE gross) at 220 hp (164 kW) at 4,600 rpm and 300 lb·ft (407 N·m) at 2,600 rpm. Optional was a four-barrel version rated at 250 hp (186 kW) at 4,800 rpm.

For 1968 only, a special high-performance version of the 302 was offered for the Shelby GT350.[6] Its main features included an angled, high-rise aluminum or iron intake manifold, a larger Holley four-barrel carburetor, and bigger valves of 1.875 in (47.6 mm) intake and 1.6 in (41 mm) exhaust. It had a longer-duration camshaft, still with hydraulic lifters. The block was made in Mexico. "Hecho en Mexico" casting marks are present in the lifter valley, and its main strength was the appearance of much larger and stronger two-bolt main bearing caps on the engine's bottom end - the same as the HP-289 but not made from nodular iron rather Ford's standard material. The heads had special close tolerance pushrod holes to guide the pushrods without rail rocker arms or stamped steel guide plates. The combustion chambers also featured a smaller quench design for a higher compression ratio and enhanced flow characteristics. Additionally, high flow cast exhaust manifolds similar to those on the 289 Hi-Po K-code engine further improved output. Heavy-duty connecting rods with high strength bolts and a nodular iron crankshaft were also included in this package. Rated power (SAE gross) was estimated at 315 hp (235 kW) at 6,000 rpm and 333 lb·ft (451 N·m) at 3,800 rpm. The package, which cost $692 (USD) including some other equipment, was not popular and did not return for 1969. This engine was not a factory engine. Rather, like all Shelby Mustang engines, it was modified by Shelby American in their capacity as a vehicle upfitter. This special engine is well documented in the Ford factory engine repair manual for 1968 Mustangs and Fairlanes. This engine block is considered the strongest production 302 block other than the Boss 302 and the Trans Am 302. The Mexican 302 block was produced through to the mid-1990s and even showed up in Ford cars, trucks and vans throughout the 1970s and early 1980s (Mexican made 302 engines were often used by the USA car plants when CEP1 couldn't produce enough engines and many Ford replacement engines were Mexican).

Note that Mexican blocks were not made from a high-nickel content material as is generally thought but rather Ford's usual ACB specification material. They are a good block but no stronger than any other USA made component and the bore service life is generally lower due to less wear resistant South American sourced iron ore. All Mexican V8 blocks were cast and machined to accept a front engine mount as required for their truck applications.

Emission regulations saw a progressive reduction in compression ratio for the 302 two-barrel, to 9.0:1 in 1972, reducing SAE gross horsepower to 210 hp (157 kW). In that year U.S. automakers began to quote horsepower in SAE net ratings; the 302 two-barrel carried a net rating of 140 hp (104 kW). By 1975 its power would drop as low as 122 hp (91 kW). Not until fuel injection began to appear in the 1980s would net power ratings rise above 210 hp (157 kW).

Throttle body fuel injection first appeared for the 302 on the Lincoln Continental in 1980, and was made standard on all applications in 1983 except manual transmission equipped Mustangs, Mercury Capris (equipped first with two-barrel (1982), then later 4-barrel carburetor (1983–85)), and also F-series trucks. The block was fitted with revised, taller lifter bosses to accept roller lifters, and a steel camshaft in 1985, and electronic sequential fuel injection was introduced in 1986. While sequential injection was used on the Mustang beginning in 1986, many other vehicles, including trucks, continued to use a batch fire fuel injection system. The speed-density based EFI systems used a large, two-piece, cast aluminum manifold. It was fitted on all engines through 1988, after which year it was replaced by a mass-air type measuring system, with the same manifold. The MAF system continued, with minor revisions, until the retirement of the engine in 2001. Ford offered a performance head that was a stock part on 1993–1995 Mustang Cobra models and pre- 1997-1/2 Ford Explorers and Mercury Mountaineers equipped with the 5.0 L engine called the GT-40 head (casting id F3ZE-AA). In mid-1997, the Explorer and Mountaineer 5.0 L heads were revised and renamed GT40P. The GT40P heads, unlike the GT40 heads, had a very well developed port shape/design which yielded ~200 cfm on the intake side and ~140 cfm on the exhaust side without increasing the size of the ports at all from standard E7TE castings, and without increasing the exhaust valve size. They also had smaller 59 - 61 cc combustion chambers for added compression, and the combustion chamber shape was revised to put the spark plug tip near the center of the chamber for a more even burn. These GT40P heads are considered by many enthusiasts to be extremely efficient. The Truck Division instigated a pushrod operated four valve per cylinder, cylinder head conversion in the early 1990s as a means of modernizing/improving and furthering the service life of the Windsor engine. This work was done for Ford by Roush Industries (for 1 million dollars) and two 302ci/5.0L and one 351ci/5.8L variants were built and tested. These engines were highly successful but upper management refused to allow engines so equipped to go into production stating that it was no longer acceptable to use a cast iron block in a new car – one of the 5.0L engines is out there in a hot rod.

The 302 was also offered for marine applications in both standard and reverse rotation setups.

From the 1978 car model year, the 302 became more commonly known as the 5.0 Liter, although its metric displacement is 4,942 cc. It is speculated that Ford used the "5.0" moniker to distinguish the 302 from their 300 cubic inch inline Six, which was known as the 4.9. Despite its advertised displacement, Car and Driver referred to the 302 as a 4.9 liter engine, even though the normal 302 Ford engine enthusiast always referred to it as a "5-Oh, 5-Point-Oh, 5 Liter, or 302".

The 302 remained a mainstay of various Ford cars and trucks through the late '90s, although it was progressively replaced by the 4.6 L Ford Modular engine starting in the early 1990s. The last 302 engine was produced for installation in a production vehicle was at Cleveland Engine Plant #1 in December 2000, as part of a build ahead to supply Ford of Australia, who installed their last such engine in a new vehicle in August 2002. The 302 is still available as a complete crate motor from Ford Racing Performance Parts.

5.6

In 2001, Ford Australia also built some stroked, 5.6 L (5,605 cc, 342 cu in) Windsors with reworked GT40P heads (featuring larger valves), a unique eight trumpet inlet manifold, long throw crank, H beam rods and roller rockers. They produced 335 hp (250 kW) at 5,250 rpm and 369 lb·ft (500 N·m) at 4,250 rpm.[7] The 5.6 litres of displacement was reached by lengthening the stroke from 76.2 mm (3.0 in) to 86.4 mm (3.4 in).[8]

Boss 302

Boss 302 engine
Main article: Ford Boss 302 engine

The Boss 302 was a chief engineer Bill Gay inspired and Bill Barr (manager) enacted performance variant of the Windsor, putting what would become Cleveland heads (this engine was still under development at this stage) on Ford's heavy duty, 4 bolt main (centre three main caps), racing block (a block that had been in existence at this specification since 1967 for the GT40 programme) to improve rated power to 290 hp (216 kW). According to some reports, the canted valve, deep breathing, high revving engine could produce more than 310 hp (231 kW), although as delivered, it was equipped with an electrical rev limiter that restricted maximum engine speed to 6150 rpm. A bulletproof bottom end, thicker cylinder walls, steel screw-in freeze plugs, race prepped crank, special HD connecting rods and Cleveland style forged pistons kept the engine together at high speeds. The key to this engine's power was the large port, large valve, quench chambered, free flowing heads. The Boss 302 Mustang was offered only for the 1969 and 1970 model years. In a January 2010 issue of Hot Rod magazine, a Boss 302 engine built to the exact specifications, settings and conditions to the original engine was tested. It produced a solid 372 hp @ 6,800rpm and 325 lb-ft of torque @ 4,200rpm.

351W

351 Windsor V8 in a 1969 Ford Mustang
The 351W is often confused with the 351 Cleveland, which is a different engine of identical displacement

The 351 cu in (5.8 L) Windsor featured a 1.3 in (32.5 mm) taller deck height than the 302, allowing a stroke of 3.5 in (88.9 mm). Although very much related in general configuration to the 289-302 and sharing the same bell housing, motor mounts and other small parts, the 351W had a unique, tall deck block, larger main bearing caps, thicker, longer connecting rods, and a distinct firing order (1-3-7-2-6-5-4-8 versus the usual 1-5-4-2-6-3-7-8, a means to move the unacceptable 'noise' of the consecutive firing adjacent front cylinders to the more rigid rear part of the engine block), adding some 25 lb (11 kg) to the engine's dry weight. The distributor is slightly different, so as to accommodate a larger oil pump shaft and larger oil pump. Some years had threaded dipstick tubes. It had a unique head which optimized torque over high-rpm breathing, frequently replaced by enthusiasts with aftermarket heads providing better performance. The early 1969 and 1970 heads had larger valves and ports for better performance. The head castings and valve head sizes from 1969 to 1976 were different, notably in passages for air injection and spark plug diameters (1969-1974 18 mm, 1975 and up 14 mm). From 1977 onward, the 351W shared the same head casting as the 302, differing only in bolt hole diameters (7/16 inch for 302, 1/2 inch for 351W). Early blocks (casting id C9OE-6015-B) had enough metal on bearing saddles 2, 3, and 4 for four bolt mains, and as with all SBF, were superior in strength to most late model, lightweight castings. Generally the 1969 to 1974 blocks are considered to be far superior in strength than the later blocks making these early units some of the strongest and most desirable in the entire SBF engine family including the 335 series. During the 1980s a four barrel version (intake manifold casting id E6TE-9425-B) was re-introduced for use in light trucks and vans. In 1988 fuel-injection replaced the four barrel carburetor. Roller camshaft/lifters were introduced in this engine in 1994.

The original connecting rod beam (forging id C9OE-A) featured drilled oil squirt bosses to lubricate the piston pin and cylinder bore and rectangular head rod bolts mounted on broached shoulders. There were a number of fatigue failures attributed to the machining of the part and so the bolt head area was spot-faced to retain metal in the critical area, requiring the use of 'football head' bolts. In 1975, the beam forging (D6OE-AA) was updated with more metal in the bolt head area. The oil squirt bosses were drilled for use in export engines, where the quality of accessible lubricants was questionable. The rod cap forging remained the same on both units (part id C9OE-A). In 1982, the design of the Essex V6 engine used a new version of the 351W connecting rod (E2AE-A), the difference between the two parts was that the V6 and V8 units was machined in metric and SAE units respectively. The cap featured a longer boss for balancing than the original design.

The block underwent some changes since its inception. In 1971, The deck height was extended from 9.480 in to 9.503 in (casting id D1AE-6015-DA) to lower the compression ratio to reduce NOx emissions without the need to change piston or cylinder head design. In 1974 a boss was added on the front of the right cylinder bank to mount the air injection pump (casting id D4AE-A). In 1974 the oil dipstick tube moved from the timing case to the skirt under the left cylinder bank near the rear of the casting. These details made swapping older blocks from passenger cars with front sump oil pans to more recent rear-sumped Mustang and LTD/Crown Vic Ford cars more difficult unless an oil pan had the dipstick mounted therein. In 1984 the rear main seal was changed from a two-piece component to a one-piece design.

Introduced in 1969, it was initially rated (SAE gross) at 250 hp (186 kW) with a two-barrel carburetor or 290 hp (216 kW) with a four-barrel. When Ford switched to net power ratings in 1972 it was rated at 153 to 161 hp (114 to 120 kW), although actual, installed horsepower was only fractionally lower than in 1971. Approximately 8.6 million 351ciW engines were manufactured between 1969-1996 at the Windsor Engine Plant Number One.

During the 1990s, motor enthusiasts were modifying 351 Cleveland 2V cylinder heads (by re-routing coolant exit from the block surfaces to the intake manifold surfaces) for use in the 351W resulting in the Clevor (combining Cleveland and Windsor). This modification required the use of custom pistons by reason of differing combustion chamber terrain (canted valves vs. straight valves) and intake manifolds. This combination yielded the horsepower potential of the 351C with the ruggedness of the 351W small block and was possible because more 351C 2V cylinder heads were manufactured than the corresponding engine blocks (the 351M and 400 used the same head as the 351C 2V).

Marinized 351

From the late 1960s through the early to mid-1990s the 351 Windsor had a long history of being marinized by Holman Moody Marine, Redline of Lewiston, ID (now defunct), Pleasure Craft Marine (PCM), and Indmar for use in about every make of recreational boat, including; Correct Craft, Ski Supreme, Hydrodyne and MasterCraft inboard competition ski boats. The early marinized engines were rated at 220 hp (164 kW). Most PCM and Indmar marinized 351’s were rated at 240 hp (179 kW). In the early 1990s, a 260 hp (194 kW) version as well as a "HO" (High Output) version that used GT-40 heads and the Holley 4160 marine carburetor was rated at 285 hp (213 kW). A few 351 GT-40/HO engines were marinized equipped with Throttle Body fuel Injection (TBI) and were rated at 310 hp (231 kW). The marine industry's relationship with the 351W platform ended when Ford was unable or unwilling to compete with GM's mass production of TBI and MPI equipped engines in mass quantity. It was during that time that the recreational marine community's small-block V8 platform of choice shifted to the 350 cu in (5.7L) GM L31 (vortec 5700) engine series.

Boss 351

The Racing Boss 351 (not to be confused with the Ford 335 engine Cleveland-based Boss 351) is a crate engine from Ford Racing Performance Parts. The block was based on the 351 cu in (5,752 cc) Ford Windsor engine, but uses Cleveland sized 2.75 in (70 mm) main bearing journals. Deck height choices include 9.2 in (234 mm) and 9.5 in (241 mm). Maximum displacements are 4.25 in (108 mm) stroke and 4.125 in (105 mm) bore.

The non cross-drilled block with increased bore capacity became available from the third quarter of 2009. A 427 cu in (6,997 cc) Boss 351-based crate engine producing 535 hp (399 kW) was available from the first quarter of 2010.

In 2010, the MSRP for the Boss 351 block was US$1,999.[9]

427

The Windsor small-block engine was bored-and-stroked to 427 cu in (7.0 L) for use in the Saleen S7 (2000-2004) and its competition model S7R (although it used Cleveland style heads). The road going engine was capable of producing 550 bhp (410 kW; 558 PS) at 6400 rpm. The S7's top speed was an estimated 220 mph (354 km/h).

In 2005, Saleen released the S7 Twin Turbo version of the car with two Garrett turbochargers producing 5.5 psi (0.4 bar) of boost, increasing the maximum power to 750 bhp (559 kW; 760 PS) at 6300 rpm, and the maximum torque to 700 lb·ft (949 N•m) at 4800 rpm. The top speed of the twin turbo S7 was 248 mph (399 km/h).

255

In 1980, an urgent need to meet EPA CAFE standards led to the creation of the 255 cu in (4.2 L) version, essentially a 302 with the cylinder bores reduced to 3.68 in (93.5 mm). The 302ci/5.0L was in fact going to be phased out and the 255ci/4.2L was to be an interim 'new' engine which would last until the new V6 was up and running - the 255ci/4.2L was a quick-fix. Rated power (SAE net) was 115-122 hp (86-91 kW), depending on year and application. Cylinder heads used smaller combustion chambers and smaller valves, and the intake ports were ovals whereas the others were rectangular. The only externally visible cue was the use of an open runner intake manifold with a stamped steel lifter valley cover attached to its underside, giving the appearance of previous generation engines, such as the Y-Block and the MEL. It was optional in Fox chassis cars including the Mustang and corporate cousin Mercury Capri, Thunderbird, Fairmont, and standard equipment in the Ford LTD. Some variants (i.e. Mercury Grand Marquis) were fitted with a variable venturi carburetor which were capable of highway fuel economy in excess of 27 MPG. Poorly received due to its dismal overall performance, the 255 was dropped after the 1982 model year with just over 250,000 units being built - 302ci/5.0L V8 engine production continued and the plans to phase it out dropped.

See also

Notes

  1. ↑ With 2001 Explorer-style water pump kit (Ford part M-8501-A50). Blocks with older pumps are 1.25" longer.
  2. ↑ Ford measures engine height here from the bottom of the oil pan to the top of valve covers, excluding any breathers or oil fill tubes.

References

  1. ↑ Ford Motor Company (1996). Ford Motorsport SVO Performance Equipment (14th ed.). (Catalog). p. 124. Ford P/N M-0750-A96.
  2. ↑ Template:Cite ,web
  3. ↑ "Mustang Specs (1964 1/2 and 1965)". Retrieved March 27, 2014.
  4. ↑ "OldRide 1964 Mercury Comet". Retrieved March 27, 2014.
  5. ↑ Ford GT40 Wikipedia
  6. ↑ http://thecarsource.com/shelby/1968/1968specs.shtml
  7. ↑ "2001 AUIII TE50 and TS50". FPV Heritage. Ford Australia. Archived from the original on 2009-10-01.
  8. ↑ Automobil Revue (2002), p. 288.
  9. ↑ Korzeniewski, Jeremy (June 13, 2009). "Ford Racing introduces new Boss 351 engine block". Autoblog.

External links

Ford Motor Company engine timeline, North American market, 1950s–1970s — Next »
Type 1950s 1960s 1970s
0123456789 0123456789 0123456789
4-cylinder engines Ford Pinto engine
I6 engines Flathead I6 Thriftpower I6
Mileage Maker I6 Truck I6
V6 engines Cologne V6
Small block V8 Flathead V8 351 Cleveland V8
Windsor V8
Ford Y-block V8 335/Modified V8
Medium block V8 FE V8
Big block V8 Lincoln Y-block V8
MEL V8 385 V8
Super Duty V8
« Previous — Ford Motor Company engine timeline, North American market, 1980s–2010s
Type 1980s 1990s 2000s 2010s
0123456789 0123456789 0123456789 01234
3-cylinder engine EcoBoost I3
4-cylinder engines Lima/OHC I4
CVH I4
HSC I4 Zetec I4
Duratec 23/25 I4
EcoBoost I4
Inline-6 engines Thriftpower Six I6
300/4.9 I6
V6 engines Cologne V6 Cologne V6 SOHC V6
Essex V6
Vulcan V6
SHO V6
Duratec (Mondeo) V6
Cyclone/Duratec/EcoBoost V6
V8 engine SHO V8
Windsor V8
335/Modified V8 Modular/Triton/InTech/Coyote V8
385 V8 Boss V8
Super Duty V8
V10 engines Triton V10
Diesel engines 6.9/7.3L IDI V8 7.3L PowerStroke V8 6.0L PowerStroke V8 6.4L PowerStroke V8 6.7L Powerstroke V8
This article is issued from Wikipedia - version of the Monday, February 08, 2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.