Flash memory

Computer memory types
Volatile
RAM
DRAM (e.g., DDR SDRAM) SRAM
In development T-RAM Z-RAM
Historical
Williams–Kilburn tube (1946–47) Delay line memory (1947) Selectron tube (1953) Dekatron
Non-volatile
ROM
Mask ROM PROM EPROM EEPROM
NVRAM
Flash memory Solid-state storage
Early stage NVRAM
nvSRAM FeRAM MRAM PRAM
Mechanical
Magnetic tape Hard disk drive Optical disc drive
In development
3D XPoint CBRAM SONOS RRAM Racetrack memory NRAM Millipede memory FJG RAM
Historical
Paper data storage (1725) Drum memory (1932) Magnetic-core memory (1949) Plated wire memory (1957) Thin-film memory (1962) Twistor memory (~1968) Bubble memory (~1970)

Flash memory is an electronic non-volatile computer storage medium that can be electrically erased and reprogrammed.

Introduced by Toshiba in 1984, flash memory was developed from EEPROM (electrically erasable programmable read-only memory). There are two main types of flash memory, which are named after the NAND and NOR logic gates. The individual flash memory cells exhibit internal characteristics similar to those of the corresponding gates.

Whereas EPROMs had to be completely erased before being rewritten, NAND type flash memory may be written and read in blocks (or pages) which are generally much smaller than the entire device. NOR type flash allows a single machine word (byte) to be written—​​to an erased location—​​or read independently.

The NAND type is primarily used in memory cards, USB flash drives, solid-state drives (those produced in 2009 or later), and similar products, for general storage and transfer of data. NAND or NOR flash memory is also often used to store configuration data in numerous digital products, a task previously made possible by EEPROM or battery-powered static RAM. One key disadvantage of flash memory is that it can endure relatively small number of write cycles in a specific block.^[1]

Example applications of both types of flash memory include personal computers, PDAs, digital audio players, digital cameras, mobile phones, synthesizers, video games, scientific instrumentation, industrial robotics, medical electronics, and so on. In addition to being non-volatile, flash memory offers fast read access times, as fast as dynamic RAM, although not as fast as static RAM or ROM. Its mechanical shock resistance helps explain its popularity over hard disks in portable devices, as does its high durability, being able to withstand high pressure, temperature, immersion in water, etc.^[2]

Although flash memory is technically a type of EEPROM, the term "EEPROM" is generally used to refer specifically to non-flash EEPROM which is erasable in small blocks, typically bytes. Because erase cycles are slow, the large block sizes used in flash memory erasing give it a significant speed advantage over non-flash EEPROM when writing large amounts of data. As of 2013, flash memory costs much less than byte-programmable EEPROM and has become the dominant memory type wherever a system requires a significant amount of non-volatile, solid-state storage.

History

Flash memory (both NOR and NAND types) was invented by Dr. Fujio Masuoka while working for Toshiba circa 1980.^[3][4] According to Toshiba, the name "flash" was suggested by Masuoka's colleague, Shōji Ariizumi, because the erasure process of the memory contents reminded him of the flash of a camera.^[5] Masuoka and colleagues presented the invention at the IEEE 1984 International Electron Devices Meeting (IEDM) held in San Francisco.^[6]

Intel Corporation saw the massive potential of the invention and introduced the first commercial NOR type flash chip in 1988.^[7] NOR-based flash has long erase and write times, but provides full address and data buses, allowing random access to any memory location. This makes it a suitable replacement for older read-only memory (ROM) chips, which are used to store program code that rarely needs to be updated, such as a computer's BIOS or the firmware of set-top boxes. Its endurance may be from as little as 100 erase cycles for an on-chip flash memory,^[8] to a more typical 10,000 or 100,000 erase cycles, up to 1,000,000 erase cycles.^[9] NOR-based flash was the basis of early flash-based removable media; CompactFlash was originally based on it, though later cards moved to less expensive NAND flash.

NAND flash has reduced erase and write times, and requires less chip area per cell, thus allowing greater storage density and lower cost per bit than NOR flash; it also has up to 10 times the endurance of NOR flash. However, the I/O interface of NAND flash does not provide a random-access external address bus. Rather, data must be read on a block-wise basis, with typical block sizes of hundreds to thousands of bits. This makes NAND flash unsuitable as a drop-in replacement for program ROM, since most microprocessors and microcontrollers require byte-level random access. In this regard, NAND flash is similar to other secondary data storage devices, such as hard disks and optical media, and is thus very suitable for use in mass-storage devices, such as memory cards. The first NAND-based removable media format was SmartMedia in 1995, and many others have followed, including:

• MultiMediaCard
• Secure Digital
• Memory Stick, and xD-Picture Card.

A new generation of memory card formats, including RS-MMC, miniSD and microSD, and Intelligent Stick, feature extremely small form factors. For example, the microSD card has an area of just over 1.5 cm², with a thickness of less than 1 mm. microSD capacities range from 64 MB to 200 GB, as of March 2015.^[10]

Principles of operation

Flash memory stores information in an array of memory cells made from floating-gate transistors. In traditional single-level cell (SLC) devices, each cell stores only one bit of information. Some newer flash memory, known as multi-level cell (MLC) devices, including triple-level cell (TLC) devices, can store more than one bit per cell by choosing between multiple levels of electrical charge to apply to the floating gates of its cells.

The floating gate may be conductive (typically polysilicon in most kinds of flash memory) or non-conductive (as in SONOS flash memory).^[11]

Floating-gate transistor

In flash memory, each memory cell resembles a standard MOSFET, except that the transistor has two gates instead of one. On top is the control gate (CG), as in other MOS transistors, but below this there is a floating gate (FG) insulated all around by an oxide layer. The FG is interposed between the CG and the MOSFET channel. Because the FG is electrically isolated by its insulating layer, electrons placed on it are trapped until they are removed by another application of electric field (e.g. Applied voltage or UV as in EPROM). Counter-intuitively, placing electrons on the FG sets the transistor to the logical "0" state. Once the FG is charged, the electrons in it screen (partially cancel) the electric field from the CG, thus, increasing the threshold voltage (V_T1) of the cell. This means that now a higher voltage(V_T2) must be applied to the CG to make the channel conductive. In order to read a value from the transistor, an intermediate voltage between the threshold voltages (V_T1 & V_T2) is applied to the CG. If the channel conducts at this intermediate voltage, the FG must be uncharged (if it were charged, we would not get conduction because the intermediate voltage is less than V_T2), and hence, a logical "1" is stored in the gate. If the channel does not conduct at the intermediate voltage, it indicates that the FG is charged, and hence, a logical "0" is stored in the gate. The presence of a logical "0" or "1" is sensed by determining whether there is current flowing through the transistor when the intermediate voltage is asserted on the CG. In a multi-level cell device, which stores more than one bit per cell, the amount of current flow is sensed (rather than simply its presence or absence), in order to determine more precisely the level of charge on the FG.

Internal charge pumps

Despite the need for high programming and erasing voltages, virtually all flash chips today require only a single supply voltage, and produce the high voltages using on-chip charge pumps.

Over half the energy used by a 1.8 V NAND flash chip is lost in the charge pump itself. Since boost converters are inherently more efficient than charge pumps, researchers developing low-power SSDs have proposed returning to the dual Vcc/Vpp supply voltages used on all the early flash chips, driving the high Vpp voltage for all flash chips in a SSD with a single shared external boost converter.^{[12][13][14][15][16][17][18][19]}

In spacecraft and other high-radiation environments, the on-chip charge pump is the first part of the flash chip to fail, although flash memories will continue to work—in read-only mode—at much higher radiation levels.^[20]

NOR flash

In NOR flash, each cell has one end connected directly to ground, and the other end connected directly to a bit line. This arrangement is called "NOR flash" because it acts like a NOR gate: when one of the word lines (connected to the cell's CG) is brought high, the corresponding storage transistor acts to pull the output bit line low. NOR flash continues to be the technology of choice for embedded applications requiring a discrete non-volatile memory device. The low read latencies characteristic of NOR devices allow for both direct code execution and data storage in a single memory product.^[21]

Programming

A single-level NOR flash cell in its default state is logically equivalent to a binary "1" value, because current will flow through the channel under application of an appropriate voltage to the control gate, so that the bitline voltage is pulled down. A NOR flash cell can be programmed, or set to a binary "0" value, by the following procedure:

• an elevated on-voltage (typically >5 V) is applied to the CG
• the channel is now turned on, so electrons can flow from the source to the drain (assuming an NMOS transistor)
• the source-drain current is sufficiently high to cause some high energy electrons to jump through the insulating layer onto the FG, via a process called hot-electron injection.

Erasing

To erase a NOR flash cell (resetting it to the "1" state), a large voltage of the opposite polarity is applied between the CG and source terminal, pulling the electrons off the FG through quantum tunneling. Modern NOR flash memory chips are divided into erase segments (often called blocks or sectors). The erase operation can be performed only on a block-wise basis; all the cells in an erase segment must be erased together. Programming of NOR cells, however, generally can be performed one byte or word at a time.

NAND flash

NAND flash also uses floating-gate transistors, but they are connected in a way that resembles a NAND gate: several transistors are connected in series, and the bit line is pulled low only if all word lines are pulled high (above the transistors' V_T). These groups are then connected via some additional transistors to a NOR-style bit line array in the same way that single transistors are linked in NOR flash.

Compared to NOR flash, replacing single transistors with serial-linked groups adds an extra level of addressing. Whereas NOR flash might address memory by page then word, NAND flash might address it by page, word and bit. Bit-level addressing suits bit-serial applications (such as hard disk emulation), which access only one bit at a time. Execute-in-place applications, on the other hand, require every bit in a word to be accessed simultaneously. This requires word-level addressing. In any case, both bit and word addressing modes are possible with either NOR or NAND flash.

To read data, first the desired group is selected (in the same way that a single transistor is selected from a NOR array). Next, most of the word lines are pulled up above the V_T of a programmed bit, while one of them is pulled up to just over the V_T of an erased bit. The series group will conduct (and pull the bit line low) if the selected bit has not been programmed.

Despite the additional transistors, the reduction in ground wires and bit lines allows a denser layout and greater storage capacity per chip. (The ground wires and bit lines are actually much wider than the lines in the diagrams.) In addition, NAND flash is typically permitted to contain a certain number of faults (NOR flash, as is used for a BIOS ROM, is expected to be fault-free). Manufacturers try to maximize the amount of usable storage by shrinking the size of the transistors.

Writing and erasing

NAND flash uses tunnel injection for writing and tunnel release for erasing. NAND flash memory forms the core of the removable USB storage devices known as USB flash drives, as well as most memory card formats and solid-state drives available today.

Vertical NAND

Vertical NAND (V-NAND) memory stacks memory cells vertically and uses a charge trap flash architecture. The vertical layers allow larger areal bit densities without requiring smaller individual cells.^[22]

Structure

V-NAND uses a charge trap flash geometry (pioneered in 2002 by AMD) that stores charge on an embedded silicon nitride film. Such a film is more robust against point defects and can be made thicker to hold larger numbers of electrons. V-NAND wraps a planar charge trap cell into a cylindrical form.^[22]

An individual memory cell is made up of one planar polysilicon layer containing a hole filled by multiple concentric vertical cylinders. The hole's polysilicon surface acts as the gate electrode. The outermost silicon dioxide cylinder acts as the gate dielectric, enclosing a silicon nitride cylinder that stores charge, in turn enclosing a silicon dioxide cylinder as the tunnel dielectric that surrounds a central rod of conducting polysilicon which acts as the conducting channel.^[22]

Memory cells in different vertical layers do not interfere with each other, as the charges cannot move vertically through the silicon nitride storage medium, and the electric fields associated with the gates are closely confined within each layer. The vertical collection is electrically identical to the serial-linked groups in which conventional NAND flash memory is configured.^[22]

Construction

Growth of a group of V-NAND cells begins with an alternating stack of conducting (doped) polysilicon layers and insulating silicon dioxide layers.^[22]

The next step is to form a cylindrical hole through these layers. In practice, a 128 Gibit V-NAND chip with 24 layers of memory cells requires about 2.9 billion such holes. Next the hole's inner surface receives multiple coatings, first silicon dioxide, then silicon nitride, then a second layer of silicon dioxide. Finally, the hole is filled with conducting (doped) polysilicon.^[22]

Performance

As of 2013, V-NAND flash architecture allows read and write operations twice as fast as conventional NAND and can last up to 10 times as long, while consuming 50 percent less power. They offer comparable physical bit density using 10-nm lithography, but may be able to increase bit density by up to two orders of magnitude.^[22]

Limitations

Block erasure

One limitation of flash memory is that, although it can be read or programmed a byte or a word at a time in a random access fashion, it can only be erased a "block" at a time. This generally sets all bits in the block to 1. Starting with a freshly erased block, any location within that block can be programmed. However, once a bit has been set to 0, only by erasing the entire block can it be changed back to 1. In other words, flash memory (specifically NOR flash) offers random-access read and programming operations, but does not offer arbitrary random-access rewrite or erase operations. A location can, however, be rewritten as long as the new value's 0 bits are a superset of the over-written values. For example, a nibble value may be erased to 1111, then written as 1110. Successive writes to that nibble can change it to 1010, then 0010, and finally 0000. Essentially, erasure sets all bits to 1, and programming can only clear bits to 0. File systems designed for flash devices can make use of this capability, for example, to represent sector metadata.

Although data structures in flash memory cannot be updated in completely general ways, this allows members to be "removed" by marking them as invalid. This technique may need to be modified for multi-level cell devices, where one memory cell holds more than one bit.

Common flash devices such as USB flash drives and memory cards provide only a block-level interface, or flash translation layer (FTL), which writes to a different cell each time to wear-level the device. This prevents incremental writing within a block; however, it does not help the device from being prematurely worn out by intensive write patterns.

Memory wear

Another limitation is that flash memory has a finite number of program–erase cycles (typically written as P/E cycles). Most commercially available flash products are guaranteed to withstand around 100,000 P/E cycles before the wear begins to deteriorate the integrity of the storage.^[23] Micron Technology and Sun Microsystems announced an SLC NAND flash memory chip rated for 1,000,000 P/E cycles on 17 December 2008.^[24]

The guaranteed cycle count may apply only to block zero (as is the case with TSOP NAND devices), or to all blocks (as in NOR). This effect is partially offset in some chip firmware or file system drivers by counting the writes and dynamically remapping blocks in order to spread write operations between sectors; this technique is called wear leveling. Another approach is to perform write verification and remapping to spare sectors in case of write failure, a technique called bad block management (BBM). For portable consumer devices, these wearout management techniques typically extend the life of the flash memory beyond the life of the device itself, and some data loss may be acceptable in these applications. For high reliability data storage, however, it is not advisable to use flash memory that would have to go through a large number of programming cycles. This limitation is meaningless for 'read-only' applications such as thin clients and routers, which are programmed only once or at most a few times during their lifetimes.

In December 2012, Taiwanese engineers from Macronix revealed their intention to announce at the 2012 IEEE International Electron Devices Meeting that it has figured out how to improve NAND flash storage read/write cycles from 10,000 to 100 million cycles using a “self-healing” process that uses a flash chip with “onboard heaters that could anneal small groups of memory cells.”^[25] The built-in thermal annealing replaces the usual erase cycle with a local high temperature process that not only erases the stored charge, but also repairs the electron-induced stress in the chip, giving write cycles of at least 100 million.^[26] The result is a chip that can be erased and rewritten over and over, even when it should theoretically break down. As promising as Macronix’s breakthrough could be for the mobile industry, however, there are no plans for a commercial product to be released any time in the near future.^[27]

Read disturb

The method used to read NAND flash memory can cause nearby cells in the same memory block to change over time (become programmed). This is known as read disturb. The threshold number of reads is generally in the hundreds of thousands of reads between intervening erase operations. If reading continually from one cell, that cell will not fail but rather one of the surrounding cells on a subsequent read. To avoid the read disturb problem the flash controller will typically count the total number of reads to a block since the last erase. When the count exceeds a target limit, the affected block is copied over to a new block, erased, then released to the block pool. The original block is as good as new after the erase. If the flash controller does not intervene in time, however, a read disturb error will occur with possible data loss if the errors are too numerous to correct with an error-correcting code.^[28][29]

X-ray effects

Most flash ICs come in ball grid array (BGA) packages, and even the ones that do not are often mounted on a PCB next to other BGA packages. After PCB Assembly, boards with BGA packages are often X-rayed to see if the balls are making proper connections to the proper pad, or if the BGA needs rework. These X-rays can erase programmed bits in a flash chip (convert programmed "0" bits into erased "1" bits). Erased bits ("1" bits) are not affected by X-rays.^[30][31]

Some manufacturers are now making X-ray proof SD^[32] and USB^[33] memory devices.

Low-level access

The low-level interface to flash memory chips differs from those of other memory types such as DRAM, ROM, and EEPROM, which support bit-alterability (both zero to one and one to zero) and random access via externally accessible address buses.

NOR memory has an external address bus for reading and programming. For NOR memory, reading and programming are random-access, and unlocking and erasing are block-wise. For NAND memory, reading and programming are page-wise, and unlocking and erasing are block-wise.

NOR memories

Reading from NOR flash is similar to reading from random-access memory, provided the address and data bus are mapped correctly. Because of this, most microprocessors can use NOR flash memory as execute in place (XIP) memory, meaning that programs stored in NOR flash can be executed directly from the NOR flash without needing to be copied into RAM first. NOR flash may be programmed in a random-access manner similar to reading. Programming changes bits from a logical one to a zero. Bits that are already zero are left unchanged. Erasure must happen a block at a time, and resets all the bits in the erased block back to one. Typical block sizes are 64, 128, or 256 KiB.

Bad block management is a relatively new feature in NOR chips. In older NOR devices not supporting bad block management, the software or device driver controlling the memory chip must correct for blocks that wear out, or the device will cease to work reliably.

The specific commands used to lock, unlock, program, or erase NOR memories differ for each manufacturer. To avoid needing unique driver software for every device made, special Common Flash Memory Interface (CFI) commands allow the device to identify itself and its critical operating parameters.

Besides its use as random-access ROM, NOR flash can also be used as a storage device, by taking advantage of random-access programming. Some devices offer read-while-write functionality so that code continues to execute even while a program or erase operation is occurring in the background. For sequential data writes, NOR flash chips typically have slow write speeds, compared with NAND flash.

Typical NOR flash does not need an error correcting code.^[34]

NAND memories

NAND flash architecture was introduced by Toshiba in 1989.^[35] These memories are accessed much like block devices, such as hard disks. Each block consists of a number of pages. The pages are typically 512^[36] or 2,048 or 4,096 bytes in size. Associated with each page are a few bytes (typically 1/32 of the data size) that can be used for storage of an error correcting code (ECC) checksum.

Typical block sizes include:

• 32 pages of 512+16 bytes each for a block size of 16 KiB
• 64 pages of 2,048+64 bytes each for a block size of 128 KiB^[37]
• 64 pages of 4,096+128 bytes each for a block size of 256 KiB^[38]
• 128 pages of 4,096+128 bytes each for a block size of 512 KiB.

While reading and programming is performed on a page basis, erasure can only be performed on a block basis.^[39]

NAND devices also require bad block management by the device driver software, or by a separate controller chip. SD cards, for example, include controller circuitry to perform bad block management and wear leveling. When a logical block is accessed by high-level software, it is mapped to a physical block by the device driver or controller. A number of blocks on the flash chip may be set aside for storing mapping tables to deal with bad blocks, or the system may simply check each block at power-up to create a bad block map in RAM. The overall memory capacity gradually shrinks as more blocks are marked as bad.

NAND relies on ECC to compensate for bits that may spontaneously fail during normal device operation. A typical ECC will correct a one-bit error in each 2048 bits (256 bytes) using 22 bits of ECC code, or a one-bit error in each 4096 bits (512 bytes) using 24 bits of ECC code.^[40] If the ECC cannot correct the error during read, it may still detect the error. When doing erase or program operations, the device can detect blocks that fail to program or erase and mark them bad. The data is then written to a different, good block, and the bad block map is updated.

Hamming codes are the most commonly used ECC for SLC NAND flash. Reed-Solomon codes and Bose-Chaudhuri-Hocquenghem codes are commonly used ECC for MLC NAND flash. Some MLC NAND flash chips internally generate the appropriate BCH error correction codes. ^[34]

Most NAND devices are shipped from the factory with some bad blocks. These are typically marked according to a specified bad block marking strategy. By allowing some bad blocks, the manufacturers achieve far higher yields than would be possible if all blocks had to be verified good. This significantly reduces NAND flash costs and only slightly decreases the storage capacity of the parts.

When executing software from NAND memories, virtual memory strategies are often used: memory contents must first be paged or copied into memory-mapped RAM and executed there (leading to the common combination of NAND + RAM). A memory management unit (MMU) in the system is helpful, but this can also be accomplished with overlays. For this reason, some systems will use a combination of NOR and NAND memories, where a smaller NOR memory is used as software ROM and a larger NAND memory is partitioned with a file system for use as a non-volatile data storage area.

NAND sacrifices the random-access and execute-in-place advantages of NOR. NAND is best suited to systems requiring high capacity data storage. It offers higher densities, larger capacities, and lower cost. It has faster erases, sequential writes, and sequential reads.

Standardization

A group called the Open NAND Flash Interface Working Group (ONFI) has developed a standardized low-level interface for NAND flash chips. This allows interoperability between conforming NAND devices from different vendors. The ONFI specification version 1.0^[41] was released on 28 December 2006. It specifies:

• a standard physical interface (pinout) for NAND flash in TSOP-48, WSOP-48, LGA-52, and BGA-63 packages
• a standard command set for reading, writing, and erasing NAND flash chips
• a mechanism for self-identification (comparable to the serial presence detection feature of SDRAM memory modules)

The ONFI group is supported by major NAND flash manufacturers, including Hynix, Intel, Micron Technology, and Numonyx, as well as by major manufacturers of devices incorporating NAND flash chips.^[42]

One major flash device manufacturer, Toshiba, has chosen to use an interface of their own design known as Toggle Mode (and now Toggle V2.0). This interface isn't directly, pin for pin compatible with the ONFI specification. The result is a product designed for one vendor's devices, can't use other vendor's devices.^[43]

A group of vendors, including Intel, Dell, and Microsoft, formed a Non-Volatile Memory Host Controller Interface (NVMHCI) Working Group.^[44] The goal of the group is to provide standard software and hardware programming interfaces for nonvolatile memory subsystems, including the "flash cache" device connected to the PCI Express bus.

Distinction between NOR and NAND flash

NOR and NAND flash differ in two important ways:

• the connections of the individual memory cells are different
• the interface provided for reading and writing the memory is different (NOR allows random-access for reading, NAND allows only page access)

These two are linked by the design choices made in the development of NAND flash. A goal of NAND flash development was to reduce the chip area required to implement a given capacity of flash memory, and thereby to reduce cost per bit and increase maximum chip capacity so that flash memory could compete with magnetic storage devices like hard disks.

NOR and NAND flash get their names from the structure of the interconnections between memory cells.^[45] In NOR flash, cells are connected in parallel to the bit lines, allowing cells to be read and programmed individually. The parallel connection of cells resembles the parallel connection of transistors in a CMOS NOR gate. In NAND flash, cells are connected in series, resembling a NAND gate. The series connections consume less space than parallel ones, reducing the cost of NAND flash. It does not, by itself, prevent NAND cells from being read and programmed individually.

Each NOR flash cell is larger than a NAND flash cell — 10 F² vs 4 F² — even when using exactly the same semiconductor device fabrication and so each transistor, contact, etc. is exactly the same size—because NOR flash cells require a separate metal contact for each cell.^[46]

When NOR flash was developed, it was envisioned as a more economical and conveniently rewritable ROM than contemporary EPROM and EEPROM memories. Thus random-access reading circuitry was necessary. However, it was expected that NOR flash ROM would be read much more often than written, so the write circuitry included was fairly slow and could only erase in a block-wise fashion. On the other hand, applications that use flash as a replacement for disk drives do not require word-level write address, which would only add to the complexity and cost unnecessarily.

Because of the series connection and removal of wordline contacts, a large grid of NAND flash memory cells will occupy perhaps only 60% of the area of equivalent NOR cells^[47] (assuming the same CMOS process resolution, for example, 130 nm, 90 nm, or 65 nm). NAND flash's designers realized that the area of a NAND chip, and thus the cost, could be further reduced by removing the external address and data bus circuitry. Instead, external devices could communicate with NAND flash via sequential-accessed command and data registers, which would internally retrieve and output the necessary data. This design choice made random-access of NAND flash memory impossible, but the goal of NAND flash was to replace mechanical hard disks, not to replace ROMs.

Attribute	NAND	NOR
Main Application	File Storage	Code execution
Storage capacity	High	Low
Cost per bit	Better	.
Active Power	Better	.
Standby Power	.	Better
Write Speed	Good	.
Read Speed	.	Good

Write endurance

The write endurance of SLC floating-gate NOR flash is typically equal to or greater than that of NAND flash, while MLC NOR and NAND flash have similar endurance capabilities. Examples of endurance cycle ratings listed in datasheets for NAND and NOR flash are provided.

Type of flash memory	Endurance rating (Erases per block)	Example(s) of flash memory
SLC NAND	100,000	Samsung OneNAND KFW4G16Q2M
MLC NAND	5,000 to 10,000 for medium-capacity applications; 1,000 to 3,000 for high-capacity applications	Samsung K9G8G08U0M (Example for medium-capacity applications)
TLC NAND	1,000	Samsung 840
SLC (floating-gate) NOR	100,000 to 1,000,000	Numonyx M58BW (Endurance rating of 100,000 erases per block); Spansion S29CD016J (Endurance rating of 1,000,000 erases per block)
MLC (floating-gate) NOR	100,000	Numonyx J3 flash

However, by applying certain algorithms and design paradigms such as wear leveling and memory over-provisioning, the endurance of a storage system can be tuned to serve specific requirements.^[48][49]

Computation of NAND flash memory endurance is a challenging subject that depends on SLC/MLC/TLC memory type as well as use pattern. In order to compute the longevity of the NAND flash, one must use the size of the memory chip, the type of memory (e.g. SLC/MLC/TLC), and use pattern.

Flash file systems

Because of the particular characteristics of flash memory, it is best used with either a controller to perform wear leveling and error correction or specifically designed flash file systems, which spread writes over the media and deal with the long erase times of NOR flash blocks. The basic concept behind flash file systems is the following: when the flash store is to be updated, the file system will write a new copy of the changed data to a fresh block, remap the file pointers, then erase the old block later when it has time.

In practice, flash file systems are only used for memory technology devices (MTDs), which are embedded flash memories that do not have a controller. Removable flash memory cards and USB flash drives have built-in controllers to perform wear leveling and error correction so use of a specific flash file system does not add any benefit.

Capacity

Multiple chips are often arrayed to achieve higher capacities^[50] for use in consumer electronic devices such as multimedia players or GPSs. The capacity of flash chips generally follows Moore's Law because they are manufactured with many of the same integrated circuits techniques and equipment.

Consumer flash storage devices typically are advertised with usable sizes expressed as a small integer power of two (2, 4, 8, etc.) and a designation of megabytes (MB) or gigabytes (GB); e.g., 512 MB, 8 GB. This includes SSDs marketed as hard drive replacements, in accordance with traditional hard drives, which use decimal prefixes.^[51] Thus, an SSD marked as "64 GB" is at least 64 × 1,000³ bytes (64 GB). Most users will have slightly less capacity than this available for their files, due to the space taken by file system metadata.

The flash memory chips inside them are sized in strict binary multiples, but the actual total capacity of the chips is not usable at the drive interface. It is considerably larger than the advertised capacity in order to allow for distribution of writes (wear leveling), for sparing, for error correction codes, and for other metadata needed by the device's internal firmware.

In 2005, Toshiba and SanDisk developed a NAND flash chip capable of storing 1 GB of data using multi-level cell (MLC) technology, capable of storing two bits of data per cell. In September 2005, Samsung Electronics announced that it had developed the world’s first 2 GB chip.^[52]

In March 2006, Samsung announced flash hard drives with a capacity of 4 GB, essentially the same order of magnitude as smaller laptop hard drives, and in September 2006, Samsung announced an 8 GB chip produced using a 40 nm manufacturing process.^[53] In January 2008, SanDisk announced availability of their 16 GB MicroSDHC and 32 GB SDHC Plus cards.^[54][55]

More recent flash drives (as of 2012) have much greater capacities, holding 64, 128, and 256 GB.^[56]

A joint development at Intel and Micron will allow the production of 32 layer 3.5 terabyte (TB) NAND flash sticks and 10 TB standard-sized SSDs. The device includes 5 packages of 16 x 48 GB TLC dies, using a floating gate cell design.^[57]

Flash chips continue to be manufactured with capacities under or around 1 MB, e.g., for BIOS-ROMs and embedded applications.

Transfer rates

Flash memory devices are typically much faster at reading than writing.^[58] Performance also depends on the quality of storage controllers which become more critical when devices are partially full.^[58] Even when the only change to manufacturing is die-shrink, the absence of an appropriate controller can result in degraded speeds.^[59]

Applications

Serial flash

Serial flash is a small, low-power flash memory that uses a serial interface, typically Serial Peripheral Interface Bus (SPI), for sequential data access. When incorporated into an embedded system, serial flash requires fewer wires on the PCB than parallel flash memories, since it transmits and receives data one bit at a time. This may permit a reduction in board space, power consumption, and total system cost.

There are several reasons why a serial device, with fewer external pins than a parallel device, can significantly reduce overall cost:

• Many ASICs are pad-limited, meaning that the size of the die is constrained by the number of wire bond pads, rather than the complexity and number of gates used for the device logic. Eliminating bond pads thus permits a more compact integrated circuit, on a smaller die; this increases the number of dies that may be fabricated on a wafer, and thus reduces the cost per die.
• Reducing the number of external pins also reduces assembly and packaging costs. A serial device may be packaged in a smaller and simpler package than a parallel device.
• Smaller and lower pin-count packages occupy less PCB area.
• Lower pin-count devices simplify PCB routing.

There are two major SPI flash types. The first type is characterized by small pages and one or more internal SRAM page buffers allowing a complete page to be read to the buffer, partially modified, and then written back (for example, the Atmel AT45 DataFlash or the Micron Technology Page Erase NOR Flash). The second type has larger sectors. The smallest sectors typically found in an SPI flash are 4 kB, but they can be as large as 64 kB. Since the SPI flash lacks an internal SRAM buffer, the complete page must be read out and modified before being written back, making it slow to manage. SPI flash is cheaper than DataFlash and is therefore a good choice when the application is code shadowing.

The two types are not easily exchangeable, since they do not have the same pinout, and the command sets are incompatible.

Firmware storage

With the increasing speed of modern CPUs, parallel flash devices are often much slower than the memory bus of the computer they are connected to. Conversely, modern SRAM offers access times below 10 ns, while DDR2 SDRAM offers access times below 20 ns. Because of this, it is often desirable to shadow code stored in flash into RAM; that is, the code is copied from flash into RAM before execution, so that the CPU may access it at full speed. Device firmware may be stored in a serial flash device, and then copied into SDRAM or SRAM when the device is powered-up.^[60] Using an external serial flash device rather than on-chip flash removes the need for significant process compromise (a process that is good for high-speed logic is generally not good for flash and vice versa). Once it is decided to read the firmware in as one big block it is common to add compression to allow a smaller flash chip to be used. Typical applications for serial flash include storing firmware for hard drives, Ethernet controllers, DSL modems, wireless network devices, etc.

Flash memory as a replacement for hard drives

One more recent application for flash memory is as a replacement for hard disks. Flash memory does not have the mechanical limitations and latencies of hard drives, so a solid-state drive (SSD) is attractive when considering speed, noise, power consumption, and reliability. Flash drives are gaining traction as mobile device secondary storage devices; they are also used as substitutes for hard drives in high-performance desktop computers and some servers with RAID and SAN architectures.

There remain some aspects of flash-based SSDs that make them unattractive. The cost per gigabyte of flash memory remains significantly higher than that of hard disks.^[61] Also flash memory has a finite number of P/E cycles, but this seems to be currently under control since warranties on flash-based SSDs are approaching those of current hard drives.^[62] In addition, deleted files on SSDs can remain for an indefinite period of time before being overwritten by fresh data; erasure or shred techniques or software that work well on magnetic hard disk drives have no effect on SSDs, compromising security and forensic examination.

For relational databases or other systems that require ACID transactions, even a modest amount of flash storage can offer vast speedups over arrays of disk drives.^[63][64]

In June 2006, Samsung Electronics released the first flash-memory based PCs, the Q1-SSD and Q30-SSD, both of which used 32 GB SSDs, and were at least initially available only in South Korea.^[65]

A solid-state drive was offered as an option with the first Macbook Air introduced in 2008, and from 2010 onwards, all Macbook Air laptops shipped with an SSD. Starting in late 2011, as part of Intel's Ultrabook initiative, an increasing number of ultra thin laptops are being shipped with SSDs standard.

There are also hybrid techniques such as hybrid drive and ReadyBoost that attempt to combine the advantages of both technologies, using flash as a high-speed non-volatile cache for files on the disk that are often referenced, but rarely modified, such as application and operating system executable files.

Flash memory as RAM

As of 2012, there are attempts to use flash memory as the main computer memory, DRAM.^[66]

Archival or long-term storage

It is unclear how long flash memory will persist under archival conditions—i.e., benign temperature and humidity with infrequent access with or without prophylactic rewrite. Anecdotal evidence suggests that the technology is reasonably robust on the scale of years.

Industry

One source states that, in 2008, the flash memory industry includes about US$9.1 billion in production and sales. Other sources put the flash memory market at a size of more than US$20 billion in 2006, accounting for more than eight percent of the overall semiconductor market and more than 34 percent of the total semiconductor memory market.^[67] In 2012, the market was estimated at $26.8 billion.^[68]

Flash scalability

Due to its relatively simple structure and high demand for higher capacity, NAND flash memory is the most aggressively scaled technology among electronic devices. The heavy competition among the top few manufacturers only adds to the aggressiveness in shrinking the design rule or process technology node.^[29] While the expected shrink timeline is a factor of two every three years per original version of Moore's law, this has recently been accelerated in the case of NAND flash to a factor of two every two years.

ITRS or company	2010	2011	2012	2013	2014	2015	2016
ITRS Flash Roadmap 2011[69]	32 nm	22 nm	20 nm	18 nm	16 nm
Updated ITRS Flash Roadmap[70]					17 nm	15 nm	14 nm
Samsung[69][70] Samsung 3D NAND[70]	35-32 nm	27 nm	21 nm (MLC, TLC)	19 nm	19-16 nm V-NAND (24L)	12 nm V-NAND (32L)	12 nm
Micron, Intel[69][70]	34-25 nm	25 nm	20 nm (MLC + HKMG)	20 nm (TLC)	16 nm	3D-NAND	3D-NAND Gen2
Toshiba, Sandisk[69][70]	43-32 nm	24 nm	19 nm (MLC, TLC)		15 nm	3D NAND BiCS	3D NAND BiCS
SK Hynix[69][70]	46-35 nm	26 nm	20 nm (MLC)		16 nm

As the feature size of flash memory cells reaches the minimum limit, further flash density increases will be driven by greater levels of MLC, possibly 3-D stacking of transistors, and improvements to the manufacturing process. The decrease in endurance and increase in uncorrectable bit error rates that accompany feature size shrinking can be compensated by improved error correction mechanisms.^[71] Even with these advances, it may be impossible to economically scale flash to smaller and smaller dimensions as the number of electron holding capacity reduces. Many promising new technologies (such as FeRAM, MRAM, PMC, PCM, ReRAM, and others) are under investigation and development as possible more scalable replacements for flash.^[72]

See also

• List of flash file systems
• microSDXC (up to 2 TB).
• Secure USB drive
• Open NAND Flash Interface Working Group
• Write amplification

References

External links

• New Pulse Measurement System For Semiconductor Device Characterization
• Semiconductor Characterization System has diverse functions
• NAND Flash Applications Design Guide by Toshiba, April 2003 v. 1.0
• Understanding and selecting higher performance NAND architectures
• How flash storage works presentation by David Woodhouse from Intel
• Flash endurance testing
• http://www.spansion.com/Support/Application%20Notes/EnduranceRetention_AN.pdf
• http://www.cse.scu.edu/~tschwarz/coen180/LN/flash.html

Solid-state drives Key terminology Encryption ECC Flash file system Flash memory SLC/MLC Flash memory controller Garbage collection IOPS MB/s Memory wear Open-channel SSD Over-provisioning Read disturb Secure erase Solid-state storage Trim command Wear leveling Write amplification Flash manufacturers IM Flash Technologies Samsung SK hynix Joint venture between SanDisk and Toshiba Controllers Independent Greenliant Systems Indilinx (liquidated in bankruptcy) JMicron Marvell Phison PMC-Sierra SandForce Captive Fusion-io Intel Micron OCZ Storage Solutions Samsung sTec SSD manufacturers List of solid-state drive manufacturers Interfaces Advanced Host Controller Interface (AHCI) Fibre Channel (FC) NVM Express (NVMe) PCI Express (PCIe) SATA Express Serial ATA (SATA) Serial attached SCSI (SAS) Universal Serial Bus (USB) Configurations HDD form factors mSATA M.2 PCI Express expansion card Related organizations INCITS JEDEC / JC-42, JC-64.8 ONFI NVMHCI Work Group USB-IF SATA-IO SFF Committee SNIA SSSI T10/SCSI T11/FC T13/ATA Category