Fiat G.55

G.55 Centauro
The second prototype G.55, MM 492, in Regia Aeronautica markings
Role	Fighter
National origin	Italy
Manufacturer	Fiat
Designer	Giuseppe Gabrielli
First flight	30 April 1942
Introduction	1943
Status	Retired
Primary users	Regia Aeronautica Repubblica Sociale Italiana Argentine Air Force Royal Egyptian Air Force
Produced	274 (wartime), 75 (postwar)[1]
Unit cost	L. 535.000 (L. 1.284.000 for planned 2.400 aircraft)[2]

The Fiat G.55 Centauro (Italian: "Centaur") was a single-engine single-seat World War II fighter aircraft used by the Regia Aeronautica and the A.N.R. (Aeronautica Nazionale Repubblicana) in 1943-1945. It was designed and built in Turin by Fiat. The Fiat G.55 was probably the best type produced in Italy during World War II,^[3] (a subjective claim also frequently made for the Macchi C.205 Veltro as well as for the Reggiane Re.2005 "Sagittario") but it did not enter production until 1943.^[4]

During its short operational service, mostly under the Repubblica Sociale Italiana insignia, after the 8 September 1943 armistice, this powerful, robust and fast aircraft proved itself to be an excellent interceptor at high altitude. In 1944, over Northern Italy, the Centauro clashed with British Supermarine Spitfire, P-51 Mustang, P-47 Thunderbolt and P-38 Lightning, proving to be no easy adversary.^[5] Italian fighter pilots liked their Centauro but by the time the war ended, fewer than 300 had been built.^[3] For comparison, the Germans produced 34,000 Bf 109s.

Design and development

By 1939, all the main Italian aircraft factories had begun designing a new series of monoplane fighter aircraft, using inline engines as opposed to the radial engines that powered the first generation Italian monoplane fighters used in the early years of World War II (fighters such as the Fiat G.50 and the Macchi C.200). This process saw the first generation radial-engined fighters re-equipped with the Italian-built copy of the Daimler-Benz DB 601 engine, the so-called Serie 1/2, whose most prominent representative was the Macchi C.202 Folgore (which was simply a Macchi C.200 with an inline V-12 instead of a radial engine). Aircraft in this series were given alphanumeric designations ending in the number "2". However, the process didn't stop, and already in 1941, designers shifted their attention on the new, larger and more powerful Fiat RA.1050, a license-built copy of the Daimler-Benz DB 605. Aircraft powered by this new engine became the "Serie 5", and all had alphanumeric designations ending in the number "5" (Macchi C.205, Reggiane Re.2005, Fiat G.55). Fiat designer Giuseppe Gabrielli, while experimenting a new version of his Fiat G.50 fighter, equipped with the DB 601, started a new design that was to be powered by the Daimler-Benz DB 605.

The first G.55 prototype flew on 30 April 1942,^[6] piloted by commander Valentino Cus, immediately showing its good performance and flight characteristics. It was armed with one 20 mm MG 151/20 cannon with 200 rounds of ammuniton, installed in the forward fuselage and firing between the cylinder banks, exiting through the propeller hub. In "Sottoserie O" airframes, there were also four 12.7 mm (.5 in) Breda-SAFAT machine guns; two in the upper engine cowling, and two in the lower cowling, firing through the propeller arc, with 300 rpg. This layout soon proved to be troublesome, both for rearming and for the servicing of the lower cowling mounted machine guns: for this reason, the two lower machine guns were removed, and replaced with a 20 mm MG 151/20 in each wing, in the later production series, the Serie 1 (for a total of three cannon and two 12.7mm machine guns, although this varied; some had machine guns in the wings instead of cannon).

The prototype flew to Guidonia, where it was put into trials against the other fighters of the so-called Serie 5: Macchi C.205V Veltro and the formidable Reggiane Re.2005 Sagittario, all of them built around the powerful, license-built Daimler-Benz DB 605 engine. The trials showed that the Centauro was the 2nd best performer overall, and it won the tender set by the Regia Aeronautica. The C.205V was good at low and medium altitudes, fast and with good diving characteristics but its performance dropped considerably over 8,000 m (26,250 ft), particularly in handling. The Re.2005 was the fastest at high altitudes and best in dogfights, but suffered from a vibration which turned out to be a balance problem. This was corrected, but was still the most technically advanced, intricate, and therefore time consuming of the three to produce, which made it unattractive at that stage of the war. The G.55 was chosen for mass production, along with the C.205. The G.55 prototype reached 620 km/h (390 mph), fully loaded, and without using WEP (war emergency power), at 7,000 m (22,970 ft). This was a little less than expected, but it had a strong airframe and was the best aircraft regarding handling and stability at every altitude. The only negative assessment noted by G.55 pilots was the pronounced left-hand yawing at takeoff due to the powerful engine torque. This was partially remedied by a slight offset positioning of the vertical stabilizer to counteract engine torque.

A Fiat G.55 with ANR livery exhibited at the Museo storico dell'Aeronautica Militare di Vigna di Valle, on Bracciano lake, in Lazio region.

By early 1943, increased Allied bombing raids over Italy had showed that there was no suitable high-altitude fighter to deal with them effectively. The Macchi C.202's performance decreased above 8,000 m (26,250 ft), the typical altitude of the bombers and its light armament of two 12.7 mm (.5 in) and two 7.7mm (.31 in) machine guns was hardly adequate to bring down heavy bombers. Of the Serie 5 fighters, the Centauro showed the best high-altitude performance, due to its large wing surface area. Also its powerful armament, along with the generous ammunition supply (the G.55 had 250 rounds of 20 mm ammunition in the centerline cannon as opposed to 120 rounds in the Re.2005) standardized in the production Serie I, was sufficient to bring down US heavy bombers.

The Regia Aeronautica commissioned the production of 1,800 G.55s, later raising that number to 2,400.^[7] A pre-production series of 34 examples was ordered: these aircraft were mostly based on the prototype, with minor changes to improve its flying characteristics. They had a different weapon layout, as stated above, with the two lower cowling machine guns moved into the wings. Only 19 of the 34 commissioned aircraft were built, and six of them were converted to the Serie I standard at the factory.

The production version, named Serie I, had the standard armament of three 20 mm MG 151/20s and two 12.7 mm (.5 in) Breda-SAFAT machine guns, plus two underwing hardpoints, allowing it to carry either two bombs (up to 160 kg/350 lb), or two drop tanks (100 L/26 US Gal). At the date of the Armistice, 8 September 1943, 35 G.55s of all Series had been delivered, including three prototypes. Of these, only one was flown to South Italy to join the Italian Co-Belligerent Air Force (a second G.55, MM.91150, was obtained by the Allies in summer 1944, when test pilot, Serafino Agostini, defected with an escaped British POW, an RAF captain, sitting on his knees. The aircraft was then taken on charge by the RAF and transferred to the Central Fighter Establishment of Tangmere, Great Britain, on 17 March 1945, with the identification number VF204 applied, was put in the depot at Ford; its final fate is unrecorded.^[8][9])

From that date on, the Centauro served with the Aeronautica Nazionale Repubblicana (ANR), the air force of the new fascist state created in North Italy by Mussolini, with the assistance of the Germans. It still not exactly known how many "Centauros" were eventually requisitioned by the Luftwaffe or those acquired by ANR. About 18 aircraft were expropriated by the ANR while 12-20 (possibly as many as 42, according to some official reports) were requisitioned by the Germans.^[8]

The Fiat factory, in Turin under German control, continued production for about six months and when on 25 April 1944, Fiat factories were heavily bombed (15 G.55s were destroyed^[9] with some trimotor Fiat G.12 transports, BR.20 bombers and CR.42LW biplane fighters ordered by the Luftwaffe). 164 "Centauros" had been completed, 97 of them being produced after the Armistice and delivered to the ANR. Following the advice of Rustungs und Kriegsproduktion Stab (RuK), the German Control Commission, production was dispersed in small cities of Monferrato and production of parts were assigned to CANSA of Novara and AVIA in Vercelli. The parts were then assembled in Turin where the aircraft were to be flown by test pilots Valentino Cus, Rolandi, Agostini and Catella.^[10] Production slowed markedly, and was stopped by the German authorities in September 1944.^[11] A total of 148 G.55s were delivered to the ANR and, when the factory was captured, 37 more examples were ready, while 73 were still on the production line, in various degrees of completion.

Operational history

The first Centauro to see operational use was the third prototype. On 21 March 1943, the aircraft was assigned to 20° Gruppo (squadron), 51° Stormo (wing) CT, based on Roma-Ciampino, for operational evaluation. In May, the G.55 followed the unit to Capoterra, near Cagliari having its baptism of fire on 5 June 1943, against Allied aircraft attacking Sardinia. The two first pre-production series flew, respectively, on 10 April and in May 1943. In early June they were assigned to 353^a Squadriglia (flight) CT based in Foligno, Umbria, were, until August, were transferred nine more aircraft.^[12] Pilots were delighted when they began to receive the new fighter in summer 1943.^[13]

In June, the first Serie I were assigned to Gruppo Complementare of 51° Stormo in Foligno, near Perugia, but in July the 11 G.55 of Gruppo Complementare were transferred to 353a Squadriglia, that already had in charge the "pre-series" machines, to operate from Roma-Ciampino Sud airfield. The 353a Squadriglia, commanded by Capitano Egeo Pittoni, flew many missions against the American bomber formations, but the flights were stopped when Rome was declared "Città aperta" (open city). On 27 August, the Squadriglie 351a and 352a left Sardinia and arrived in Foligno to be re-equipped with G.55. But at the date of the 8 September the G.55 had not been delivered yet. During the first week of September, 12 Centauros had been assigned to 372a Squadriglia of 153° Gruppo in Torino-Mirafiori.^[14] On 8 September 1943, the date of Armistice, the Regia Aeronautica had received 35 G.55s. Only one of them flew to southern Italy, accepting the invitation of Maresciallo d'Italia Pietro Badoglio to surrender to Allied forces.

ANR service

There still is no exact data about the G.55's captured by the Luftwaffe or acquired by Aeronautica Nazionale Repubblicana. About 18 G.55s were acquired by ANR while 12-20, or even 42, according to some reports, were requisitioned by the Luftwaffe.^[12] The Centauro entered in service with the ANR; a decision was made to produce 500 G.55s, of which 300 were G.55/I and 200 G.55/II Serie II, armed with five 20 mm MG 151/20s and no machine guns (one in the centerline, two in the upper cowling, two in the wings). Only 148 were delivered to the ANR units that, as the number of available G.55s dwindled, were progressively re-equipped with the Bf 109G, of various sub-versions, even though Italian pilots preferred the G.55, with cancellation of production being extremely unpopular.^[11]

The ANR had two Gruppi Caccia terrestre (fighter squadrons), the first was initially equipped with the Macchi C.205, from November 1943 to May 1944, then, re-equipped with the G.55/I in June 1944 until it switched to the Bf 109G starting from November 1944. The 2nd Gruppo was the main unit equipped with the G.55, of which it had 70 examples from December 1943-August 1944, before being progressively re-equipped with the Bf 109G.

The first unit in ANR to be equipped with G.55 was the Squadriglia Montefusco, in November 1943, operating from Piemonte until 29 March 1944, when it was absorbed by the 1st Gruppo and transferred in Veneto. The 2nd Gruppo was formed at Bresso. It was initially commanded by Lt Col Antonio Vizzoto, and later by Lt Col Aldo Alessandrini.^[15] It had three Squadriglie (the 4th, Gigi Tre Osei, the 5th, Diavoli Rossi, and the 6th, Gamba di Ferro). The unit operated near Milan and Varese until April 1944, then it was transferred near Parma and Pavia, then again near the Lake Garda (Brescia and Verona). At the end of May, the 2° Gruppo gave its G.55s to 1° Gruppo and re-equipped with 46 exI./JG 53 and II.JG 77 Bf 109G-6/R6^[15]

With the ANR, the G.55s gave a good account of themselves against Allied fighters like the Spitfire and Mustang.^[16]

German interest

In December 1942, a technical commission of the Regia Aeronautica was invited by the Luftwaffe to test some German aircraft in Rechlin. The visit was part of a joint plan for the standardization of the Axis aircraft production. In the same time, some Luftwaffe officers visited Guidonia where they were particularly interested in the performance promised by the Serie 5 fighters. On 9 December, these impressions were discussed in a Luftwaffe staff meeting and raised the interest of Hermann Göring himself. In February 1943, a German test commission was sent in Italy to evaluate the new Italian fighters.^[17] The commission was led by Oberst Petersen and was formed by Luftwaffe officers and pilots and by technical personnel, among them the Flugbaumeister Malz. The Germans also brought with them several aircraft including a Fw 190 A-5 and a Bf 109 G-4 for direct comparison tests in simulated dogfights.

The tests began 20 February 1943 with the German commission very impressed by the Italian aircraft, the G.55 in particular. In general, all the Serie 5 fighters were very good at low altitudes, but the G.55 was also competitive with its German opponents in term of speed and climb rate at high altitudes, while still maintaining superior handling characteristics. The definitive evaluation by the German commission was "excellent" for the G.55, "excellent" for the Re.2005 although very complicated to produce, and merely "average" for the C.205. Oberst Petersen defined the G.55 "the best fighter in the Axis" and immediately telegraphed his impressions to Goering. After listening the recommendations of Petersen, Milch and Galland, a meeting held by Goering on 22 February 1943 voted to produce the G.55 in Germany.

German interest, apart from the good test results, derived also from the development possibilities they were able to see in the G.55 and in the Re.2005. Particularly, the G.55 was bigger and heavier and was considered a very good candidate for the new, significantly larger and more powerful DB 603 engine, which was considered too large to fit in the Bf 109's airframe. Other visits were organized in Germany during March and May 1943 in Rechlin and Berlin. The G.55 was again tested at Rechlin at the presence of Milch. Gabrielli and other FIAT personnel were invited to visit German factories and to discuss the evolution of the aircraft. The specifications of the German G55/II included the DB 603 engine, five 20 mm guns and a pressurized cockpit. The suggestion of weapons in the wings, limited to one 20 mm gun for each wing, originated the final configuration of the Serie I, while the DB 603 engine was successfully installed in what became the G.56 prototype. As a concrete results of the German interest in the G.55, the Luftwaffe acquired three complete G.55/0 airframes (MM 91064-65-66) for evaluations and experiments providing three DB 603 engines and original machinery for the setup of other production line of the Italian copy of DB 605. Two of the Luftwaffe G.55's remained in Turin, at the Aeritalia plants, where they were used by German and Italian engineers to study the planned modifications and the possible optimizations to the production process. Later these two were converted to Serie I and delivered to the ANR. The third one was transferred to Rechlin for tests and experiments in Germany. The DB 603 engines were used to build the G.56 prototypes.

The interest in the G.55 program was still high after the Armistice. In October 1943, Kurt Tank, who previously personally tested a G.55 in Rechlin, and who had had nothing but praise for the aircraft, was in Turin to discuss G.55 production. However, events in the war and the not yet optimized production process were the reasons for which the G.55 program was eventually abandoned by the Luftwaffe. Early production of G.55 required about 15,000 man-hours; while there were estimations to reduce the effort to about 9,000 man-hours, the well-practiced German factories were able to assemble a Bf 109 in only 5,000 man-hours. The DB 603 were instead to be used in Tank's own Ta-152C.

G.55 S prototype c. 1945

Torpedo fighter

The Regia Aeronautica employed torpedo bombers with some success in the early war years, with the trimotor, SIAI-Marchetti SM.79 Sparviero medium bomber inflicting considerable losses on Allied shipping in the Mediterranean Sea. By late 1942 the aging Sparviero was facing continually improving Allied fighters and anti aircraft defences, leading to the General staff exploring the idea of using a fighter aircraft for torpedo attacks. A fighter operating from Italian coasts with an operational range of 300–400 km (190-250 mi), would be capable of delivering a torpedo at high speed, and would be better able to evade enemy fighters or engage them after the attack run.

Fiat was asked to begin studies for a G.55 conversion to carry a 680 kg (1,500 lb) aerial torpedo, a shorter and more compact version of the standard weapon used by the SM.79. With the decision to develop a G.57, whose specifications included the capability of carrying torpedoes, all similar work on the G.55 torpedo fighter was suspended.

Later, after the G.57 project was dropped, and given the ANR's continuing need for an aircraft that could replace the SM.79, the ANR engineers undertook the task of converting the Centauro for the torpedo attack role. A production aircraft (military serial number MM. 91086) was modified to carry a 920 kg (2,030 lb), 5.46 m (17.91 ft) long torpedo. The engine coolant radiator, normally a single unit positioned on the belly of the fuselage under the cockpit area, was divided into two units mounted under the wing roots (similar to the layout used on the Bf 109), gaining a 90 cm (35 in) space where two racks were mounted to carry the torpedo. The tailwheel strut was lengthened and equipped with a strengthened shock absorber to keep the tailfins of the torpedo from striking the ground, and a drag-reducing cowling was added in front of the tailwheel to minimize drag from the lengthened strut. The two 12.7 mm (.5 in) Breda-SAFAT machine guns were removed to reduce weight, leaving the aircraft with the three 20 mm cannons only as fixed armament.^[18]

The aircraft, designated G.55S, first flew in August 1944 and was successfully tested in January 1945,^[11] piloted by Adriano Mantelli. Despite the cumbersome external load, performance was good and the handling acceptable. The ANR ordered a pre-series of 10 examples and a production series of 100 aircraft, but the conclusion of the war put an end to the project. The G.55S prototype survived the war and, after being converted back to the Serie I standard, it became the first G.55 to be delivered to the newly formed Aeronautica Militare Italiana (AMI).

Fiat G.56

Fiat G.56

The Fiat G.56 was basically a Fiat G.55 with a larger German Daimler-Benz DB 603 engine. Two prototypes were built, flight tests starting in March 1944.^[11] On 30 March, Commander Valentino Cus reached speeds of 690/700 km/h (430/440 mph).^[19] Official maximum speed was 685 km/h (426 mph) and the aircraft was armed with three 20 mm MG 151/20s, one firing through the propeller hub, the other two installed in the wings.^[20] While performance was excellent, the aircraft proving superior to both the Bf 109K and Bf 109G and Fw 190A, outmanoeuvring ^[3] all types in testing, production was not allowed by the German authorities.^[11]

After World War II

In 1946, Fiat restarted production of the G.55, using the large stock of partly complete airframes and components remaining in its factories. It was available in two versions, the G.55A, a single-seat fighter/advanced trainer, and the G.55B, a two-seat advanced trainer, whose prototypes flew on 5 September 1946 and 12 February 1946 respectively.^[20]

The AMI acquired 19 G.55As and 10 G.55Bs, while the Argentine Air Force purchased 30 G.55As, and 15 G.55Bs.^[21]

G.59

Fiat G.59

The production of these orders for G.55s for Italy and Argentina caused the available stocks of the Italian licence-built version of the DB 605 engine to run short. As there was still a demand for the aircraft, it was decided to convert the type to use the more readily available Rolls-Royce Merlin engine, with the first conversion flying in early 1948.^[22] The conversion was successful, and the AMI decided to convert its G.55s to Merlin power, these re-entering service at the Lecce flying school in 1950 as the G.59-1A and G.59-1B (single- and two-seat versions).^[23]

Syria placed an order for 30 similar aircraft, which by this time, were completely from new production as the stocks of G.55 components had been exhausted. Of these, 26 were single-seaters (designated G.59-2A) and the remaining 4 two-seaters (G.59-2B).^[22] A single G.59-2A was acquired by Argentina for evaluation, but no further orders followed from the South American republic.

The final versions were the G.59-4A single-seater and G.59-4B two-seater, which were fitted with bubble canopies for improved visibility. 20 G.59-4As and ten G.59-4Bs were purchased by Italy.^[22]

Variants

G.55

3 prototypes.

G.55/0

16 pre-production aircraft.

G.55/1

15 initial production aircraft.

G.55/2

Bomber interceptor version.

G.55/S

Torpedo attack aircraft variant.

G.55/A,B

Single-seat/twin-seat trainer versions, developed after the conflict.

G.56

2 prototypes with 1,300 kW (1,750 hp) Daimler-Benz DB 603A engines.

G.57

Version planned with A 930 kW (1,250 hp) Fiat A.83 R.C.24/52 radial engine.

G.59-1A

Rolls-Royce Merlin powered single-seat advanced trainers converted from G.55s

G.59-1B 

Rolls-Royce Merlin powered two-seat trainers converted from G.55s

G.59-2A

26, new production, Rolls-Royce Merlin powered single-seaters for Syria

G.59-2B

4, new production, Rolls-Royce Merlin powered two-seat trainers for Syria

G.59-4A

20, new production, Rolls-Royce Merlin powered single-seaters for the Regia Aeronautica, fitted with bubble canopies.^[24]

G.59-4B

10, new production, Rolls-Royce Merlin powered two-seaters for the Regia Aeronautica, fitted with bubble canopies.^[24]

Operators

Syrian Fiat G.55

 Argentina

• Argentine Air Force

 Egypt

• Royal Egyptian Air Force

 Kingdom of Italy

• Regia Aeronautica

 Italian Social Republic

• Aeronautica Nazionale Repubblicana

 Italy

• Italian Air Force operated 74 Fiat G.59 retired in 1965^[25]

 Syria

• Syrian Air Force

Specifications (G.55/I)

Data from "Centauro - The Final Fling"^[26]

General characteristics

• Crew: 1
• Length: 9.37 m (30 ft 9 in)
• Wingspan: 11.85 m (38 ft 10 in)
• Height: 3.13 m (without the antenna mast) (10 ft 3¼ in)
• Wing area: 21.11 m² (227.23 ft²)
• Empty weight: 2,630 kg (5,798 lb)
• Loaded weight: 3,520 kg (7,760 lb)
• Max. takeoff weight: 3,718 kg (8,197 lb)
• Powerplant: 1 × Fiat RA.1050 R.C.58 Tifone (license-built Daimler-Benz DB 605A-1) liquid-cooled inverted V-12, 1,085 kW (1,475 hp)

Performance

• Maximum speed: 623 km/h (671 km/h with WEP) (337 kn, 387 mph (417 mph with WEP)) at 7,000 m (22,970 ft)
• Range: 1,200 km, or 1,650 km with two 100 l (26 US Gal) drop tanks under wings (545 nmi, 627 mi (or 891 nmi, 1,025 mi with drop tanks ))
• Service ceiling: 12,750 m (41,830 ft)
• Rate of climb: 5 min 50 sec at 6,000 m (Dimensione Cielo, Caccia Assalto 3 Edizioni Bizzarri, Roma 1972, pag. 15) ()
• Wing loading: 154.0 kg/m² (34.15 lb/ft²)
• Power/mass: 0.308 kW/kg (0.190 hp/lb)
  
• Climb to 7,000 m (22,970 ft): 8.57 min

Armament

G.55 Serie 0:

• 1 × 20 mm Mauser MG 151/20 cannon, engine-mounted (250 rounds)
• 4 × 12.7 mm (.5 in) Breda-SAFAT machine guns, two in the upper engine cowling, two in the lower cowling/wing roots (300 rpg)

G.55 Serie I:

• 3 × 20 mm MG 151/20s, one engine-mounted (250 rounds) and two wing-mounted (200 rpg)
• 2 × 12.7 mm Breda-SAFAT machine guns in the upper engine cowling (300 rpg)
• Provision for 2 × 160 kg (353 lb) bombs on underwing racks (N.B. Egyptian and Syrian aircraft used Machine guns in the wings instead of cannon)

See also

Wikimedia Commons has media related to Fiat G.55.

Related development

• Fiat G.50

Aircraft of comparable role, configuration and era

• Macchi C.205
• Messerschmitt Bf 109G
• North American P-51D Mustang
• Reggiane Re.2005

Related lists

• List of aircraft of World War II
• List of aircraft of Italy in World War II

References

Notes

Bibliography

Further reading

• Baldini, Atilio; Bontti, Sergio (2006). Núñez Padin, Jorge Felix, ed. Fiat G55A/B Centauro & G59-1A. Serie Fuerza Aérea Argentina (in Spanish) 10. Bahía Blanca, Argentina: Fuerzas Aeronavales. 

External links

• Virtual G55 project
• Fiat G.55 Centauro