Gasoline direct injection

In non-Diesel internal combustion engines, Gasoline Direct Injection (GDI), also known as Petrol Direct Injection, Direct Petrol Injection, Spark Ignited Direct Injection (SIDI) and Fuel Stratified Injection (FSI), is a variant of fuel injection employed in modern two-stroke and four-stroke gasoline engines. The gasoline is highly pressurized, and injected via a common rail fuel line directly into the combustion chamber of each cylinder, as opposed to conventional multi-point fuel injection that injects fuel into the intake tract, or cylinder port. Directly injecting fuel into the combustion chamber requires high pressure injection whereas low pressure is used injecting into the intake tract or cylinder port.

In some applications, gasoline direct injection enables a stratified fuel charge (ultra lean burn) combustion for improved fuel efficiency, and reduced emission levels at low load.

Combustion chamber of a 3.5 L (210 cu in) Ford EcoBoost engine

Theory of operation

The major advantages of a GDI engine are increased fuel efficiency and high power output. Emissions levels can also be more accurately controlled with the GDI system. The cited gains are achieved by the precise control over the amount of fuel and injection timings that are varied according to engine load. In addition some engines operate on full air intake. That is, there is no air throttle plate eliminating air throttling losses in some GDI engines, when compared to a conventional fuel-injected or carbureted engine, which greatly improves efficiency, and reduces piston 'pumping losses'. Engine speed is controlled by the engine control unit/engine management system (EMS), which regulates fuel injection function and ignition timing, instead of having a throttle plate that restricts the incoming air supply. Adding this function to the EMS requires considerable enhancement of its processing and memory, as direct injection plus the engine speed management must have very precise algorithms for good performance and drivability.

Piston of a 3.5 L (210 cu in) Ford EcoBoost engine with a swirl cavity on the top

The engine management system continually chooses among three combustion modes: ultra lean burn, stoichiometric, and full power output. Each mode is characterized by the air-fuel ratio. The stoichiometric air-fuel ratio for gasoline is 14.7:1 by weight (mass), but ultra lean mode can involve ratios as high as 65:1 (or even higher in some engines, for very limited periods). These mixtures are much leaner than in a conventional engine and reduce fuel consumption considerably.

It is also possible to inject fuel more than once during a single cycle. After the first fuel charge has been ignited, it is possible to add fuel as the piston descends. The benefits are more power and economy, However, certain octane fuels have caused exhaust valve erosion.

Companion technologies

Direct injection may also be accompanied by other engine technologies such as turbocharging or supercharging, variable valve timing (VVT) or continuous variable cam phasing, and tuned/multi path or variable length intake manifolding (VLIM, or VIM). Water injection or (more commonly) exhaust gas recirculation (EGR) may help reduce the high nitrogen oxides (NOx) emissions that can result from burning ultra lean mixtures; modern turbocharged engines use continuous cam phasing in place of EGR.

Tuning up an early generation FSI power plant to generate higher power is difficult, since the only time it is possible to inject fuel is during the induction phase. Conventional injection engines can inject throughout the 4-stroke sequence, as the injector squirts onto the back of a closed valve. A direct injection engine, where the injector injects directly into the cylinder, is limited to the intake stroke of the piston. As the RPM increases, the time available to inject fuel decreases. Newer FSI systems that have sufficient fuel pressure to inject even late in compression phase do not suffer to the same extent; however, they still do not inject during the exhaust cycle (they could but it would just waste fuel). Hence, all other factors being equal, an FSI engine needs higher-capacity injectors to achieve the same power as a conventional engine. Some engines overcome this limitation by using both direct injection and multiport fuel injection (Toyota 2GR-FSE V6).

History

Early systems

An Antoinette fuel-injected V8 aviation engine of 1909, mounted in a preserved Antoinette VII monoplane aircraft.

The invention of direct gasoline injection was by the French inventor of the V8 engine configuration, Leon Levavasseur in 1902.[4] Levavasseur designed the original Antoinette firm's series of V-form aero engines, starting with the Antoinette 8V to be used by the aircraft the Antoinette firm built that Levavasseur also designed, flown from 1906 to the firm's demise in 1910, with the world's first V16 engine, using Levavasseur's direct injection and producing some 100 hp, flying an Antoinette VII monoplane in 1907.

The first post-World War I example of direct gasoline injection was on the Hesselman engine invented by Swedish engineer Jonas Hesselman in 1925.[5][6] Hesselman engines used the ultra lean burn principle and injected the fuel in the end of the compression stroke and then ignited it with a spark plug, it was often started on gasoline and then switched over to run on diesel or kerosene. The Hesselman engine was a low compression design constructed to run on heavy fuel oils.

Direct gasoline injection was applied during the Second World War to almost all higher-output production aircraft powerplants made in Germany (the widely used BMW 801 radial, and the popular inverted inline V12 Daimler-Benz DB 601, DB 603 and DB 605, along with the similar Junkers Jumo 210G, Jumo 211 and Jumo 213, starting as early as 1937 for both the Jumo 210G and DB 601), the Soviet Union's (Shvetsov ASh-82FN radial, 1943, Chemical Automatics Design Bureau - KB Khimavtomatika) and the US (Wright R-3350 Duplex Cyclone radial, 1944).

Bosch were already at work on the mechanical direct injection DKW-Meisterklasse engine at the end of the 1930s with good test results.[7] The Second World War stopped further development.

The first automotive direct injection system used to run on gasoline was developed under Hans Scherenberg’s leadership, and was introduced by Goliath and Gutbrod in 1952 to power some of their two-stroke cars. This system made by Bosch was basically a high-pressure diesel direct-injection pump with an intake throttle valve set up. (Diesels only change the amount of fuel injected to vary output; there is no throttle.) It used a normal gasoline fuel pump, to provide fuel to a mechanically driven injection pump, which had separate plungers per injector to deliver a very high injection pressure directly into the combustion chamber. The two-stroke vehicles showed very good performance and up to 30% less fuel consumption over the carburetor version, primarily under low engine loads.[7] The cars enjoyed an extra benefit as the injection system also metered lubricant into the engine from a dedicated oil tank, obviating the need for owners to mix their own two-stroke fuel blend. A portion of the oil was combined with fuel in the injection pump to lubricate the cylinders and piston rings, the rest was ported to the air intake to lubricate the crankcase.[8] But the cars were expensive and difficult to start when the engine was warm due to vapor locks. Also, very few people knew about direct injection, and the injection pumps needed frequent adjustment. Branded repair shops and Bosch services became overloaded, and many cars were converted to carburetor. These two-stroke engines were soon superseded by four-strokes.

The 1955 Mercedes-Benz 300SL, the first production sports car to use fuel injection, used direct injection. The Bosch fuel injectors were placed into the bores on the cylinder wall used by the spark plugs in other Mercedes-Benz six-cylinder engines (the spark plugs were relocated to the cylinder head). Later, more mainstream applications of fuel injection favored the less-expensive indirect injection methods.

Research was conducted in the early 1970s with the backing of American Motors Corporation (AMC) to develop a Straticharge Continuous Fuel-Injection (SCFI) system.[9] The conventional spark ignited internal combustion AMC straight-6 engine was modified with a redesigned cylinder head. The system incorporated a mechanical device that automatically responded to the engine’s airflow and loading conditions with two separate fuel-control pressures supplied to two sets of continuous-flow injectors.[10] Flexibility was designed into the SCFI system for trimming it to a particular engine.[11] Prototype "straticharge" engine road testing was performed using a 1973 AMC Hornet, but the mechanical fuel controls had teething problems.[12]

The Ford Motor Company developed a stratified-charge engine in the late 1970s called "PROCO" (programmed combustion)[13][14] using a unique high-pressure pump and direct injectors. At least one hundred and fifteen (115) Crown Victoria cars were built at Ford's Atlanta Assembly in Hapeville, Georgia using a PROCO V8 engine. The project was canceled for several reasons: electronic controls, a key element, were in their infancy; pump and injector costs were extremely high; and lean combustion produced nitrogen oxides in excess of near future United States Environmental Protection Agency (EPA) limits.[15] Also, the PROCO system was being launched in the late 1970s, a time of the second "gas crisis" in the US, which drove fuel costs higher. PROCO had been initially developed for Ford's 460 Cubic inch V8 engine line, later applied to the 351, and eventually the 302. Because the extreme fuel cost spike, Ford was unsure of the future market for V8 engines, and chose not to commit to such an expensive technology in unstable times.

Later systems

In 1996 gasoline direct injection reappeared in the automotive market. Mitsubishi was the first with a GDI engine in the Japanese market with its Galant/Legnum's 4G93 1.8 L inline-four.[16][17] It was subsequently brought to Europe in 1997 in the Carisma,[18] although the engine was a failure due to high emissions and poor fuel efficiency.[19] It also developed the first six-cylinder GDI powerplant, the 6G74 3.5 L V6, in 1997.[20] Mitsubishi applied this technology widely, producing over one million GDI engines in four families by 2001.[21] Although in use for many years, on September 11, 2001 MMC claimed a trademark for the acronym 'GDI' (with an uppercase final "I").[22]

In 1997 Nissan released the Leopard featuring the VQ30DD equipped with direct injection.[23]

In 1998, Toyota's D4 direct injection system first appeared on various Japanese market vehicles equipped with the SZ and NZ engines.[24][25][26] Toyota later introduced its D4 system to European markets with the 1AZ-FSE engine found in the 2001 Avensis.[27] and US markets in 2005 with the 3GR-FSE engine found in the Lexus GS 300. Toyota's 2GR-FSE V6 first found in the Lexus IS 350 uses a more advanced direct injection system, which combines both direct and indirect injection using two fuel injectors per cylinder, a traditional port fuel injector (low pressure) and a direct fuel injector (high-pressure) in a system known as D4-S.[28]

In 1999, Renault introduced the 2.0 IDE (Injection Directe Essence),[29] first on the Megane. Rather than following the lean burn approach, Renault's design uses high ratios of exhaust gas recirculation to improve economy at low engine loads, with direct injection allowing the fuel to be concentrated around the spark.[30] Later gasoline direct injection engines have been tuned and marketed for their high performance as well as increased fuel efficiency. PSA Peugeot Citroën, Hyundai, and Volvo entered into a development agreements and licensed Mitsubishi's GDI technology in 1999.[31][32][33][34][35] The Mitsubishi engines were also produced in the NedCar factory and used in the 1.8 L Carisma and the GDI-powered Volvo S40/V40 models.[36][37]

In 2000, the Volkswagen Group introduced its gasoline direct injection engine in the Volkswagen Lupo, a 1.4 L inline-four unit, under the product name "Fuel Stratified Injection" (FSI) and "Turbo Fuel Stratified Injection" (TFSI).[38] The technology was adapted from Audi's Le Mans prototype race car R8. Volkswagen Group marques use direct injection in its turbocharged 2.0 L TFSI and naturally aspirated 2.0 L FSI four-cylinder engines. Later, a 1.6 L inline-four unit was introduced in the MY 2002 Volkswagen Golf Mk4/Jetta/Bora, a 1.4L in the MY 2002 Volkswagen Polo Mk4 and a 2.0L in the model year 2003 Audi A4. PSA Peugeot Citroën introduced its first GDi (HPi) engine in 2000 in the Citroën C5 and Peugeot 406. It was a 2.0-liter 16-valve EW10 D unit with 140 hp (104 kW), the system was licensed from Mitsubishi.[33][37][39]

In 2002, the Alfa Romeo 156 with a direct-injection engine, the JTS (Jet Thrust Stoichiometric) went on sale[40] and today the technology is used on almost every Alfa Romeo engine.

In 2003, Ford debuted a 1.8 L Duratec SCi naturally aspirated engine for the Mondeo.[41] Ford introduced its first European Ford engine to use direct injection technology in 2001, badged SCi (Smart Charge injection) for Direct-Injection-Spark-Ignition (DISI).[41] The range will include some turbocharged derivatives, including the 1.0 L, three-cylinder turbocharged unit showcased at the 2002 Geneva Show.[41]

In 2003, BMW introduced a low-pressure gasoline direct injection N73 V12.[42] This initial BMW setup could not enter lean-burn mode, but the company introduced its second-generation High Precision Injection (HPI) system on the new turbocharged N54 straight-6 in 2006, which used high-pressure injectors.[43] This system surpasses many others with a wider envelope of lean-burn time, increasing overall efficiency.[44] PSA is cooperating with BMW on a new line of engines that made its first appearance in the 2007 MINI Cooper S. Honda released their own direct injection system on the Stream sold in Japan.[45] Honda's fuel injector is placed directly atop the cylinder at a 90-degree angle rather than a slanted angle.[45]

In 2003, General Motors released a 155 hp (116 kW) version of the 2.2 L Ecotec for the Opel/Vauxhall Vectra and Signum. Several direct injected versions of the Ecotec engine have been introduced, using the SIDI (Spark Ignition Direct Injection) moniker: in 2006, a 2.0 L turbocharged Ecotec LNF using a Gen II block for the Pontiac Solstice GXP and the Saturn Sky Red Line; in 2010, a Gen II block 2.4 L Ecotec LAF; and in 2012, a 2.5 L Ecotec LCV and 2.0 L turbocharged Ecotec LTG in a Gen III block.

In 2004 Isuzu produced the first GDi engine sold in a mainstream American vehicle, standard on the 2004 Axiom and optional on the 2004 Rodeo. Isuzu claimed the benefit of GDi is that the vaporizing fuel has a cooling effect, allowing a higher compression ratio (10.3:1 versus 9.1:1) that boosts output by 20 hp (15 kW), and that 0-to-60 mph times drop from 8.9 to just 7.5 seconds, with the quarter-mile being cut from 16.5 to 15.8 seconds.[46]

In 2005, Mazda began to use their own version of direct-injection in the Mazdaspeed6 and later on the CX-7 sport-utility, and the new Mazdaspeed3 in the US and European market. It is referred to as Direct Injection Spark Ignition (DISI).

In 2006, BMW released the new N54 twin-turbo-charged direct injection inline-six engine for its 335i Coupe and later for the 335i Sedan, 535i series. and the 135i models.[47][48] Mercedes-Benz released its direct injection system (Charged Gasoline Injection, or "CGI") on the CLS 350 CGI featuring common rail, piezo-electric direct fuel injectors. The CLS 350 CGI offers 292 BHP versus 272 BHP for the CLS 350, with reduced carbon dioxide emissions and improved fuel economy.[49] Audi also released its V8 engine with FSI technology in Audi R8 that can produce 424 BHP with low carbon emission and more fuel economy.[50][51]

In 2007, GM released the 3.6 L V6 LLT SIDI for the redesigned Cadillac CTS and STS and the Holden Commodore SV6. The 3.6 L has been used in the 2010 Chevy Camaro, a first for this model. In 2010, the 3.0 L LF1 SIDI was introduced.

In 2007, Ford introduced its EcoBoost engine technology designed for a range of vehicles. The engine first appeared in the 2007 Lincoln MKR Concept under the name TwinForce.[52] The EcoBoost family of 4-cylinder and 6-cylinder engines features turbocharging and direct injection technology (GTDI - Gasoline Turbocharged Direct Injection).[52] A 2.0 L version was unveiled in the 2008 Explorer America Concept.[52]

In 2008, BMW released the X6 xDrive50i equipped with a direct injected twin turbo N63 V8 engine.[53]

In 2009, Ferrari began selling the front-engine California with a direct injection system, and announced the 458 Italia will also feature a direct injection system, a first for Ferrari mid-rear engine setups.[54] Porsche also began selling the 997 and Cayman equipped with direct injection. Ford produced the new generation Taurus SHO and Flex with a 3.5 L twin-turbo EcoBoost V-6 with direct injection.[55] The Jaguar Land Rover AJ-V8 Gen III 5.0 L engine (introduced in August 2009 for the 2010 model year) features spray-guided direct injection.

In 2010 Infiniti produced the M56 which includes DI. Motus Motorcycles is developing, with Katech Engines, a direct-injected V4 engine named the KMV4 as the powertrain for their MST motorcycles. In 2011 the Hyundai Sonata 2011 model will come with GDI engines, including a turbo charged 2.0-litre that produces 274 hp.[56]

In 2013 the Acura RLX came with direct-injection, becoming the first Honda GDI V6.

The 2014 General Motors LT1 (separate from the 1990s era LT1 / LT4 engines), a 6.2 L V8, will use direct injection as well as VVT and variable displacement (cylinder deactivation). The 2014 Hyundai Accent features an aluminum block, 138 , I4 GDI engine.

In two-stroke engines

The benefits of direct injection are even more pronounced in two-stroke engines, because it eliminates much of the pollution they cause. In all two-strokes other than those with split-single engines or similarly sophisticated arrangements, the exhaust and intake ports are both open at the same time, at the bottom of the piston stroke, for "scavenging". In conventional two-strokes, a portion of the fuel/air mixture entering the cylinder from the crankcase through the intake ports goes directly out, unburned, through the exhaust port. With direct injection, only air (and usually some oil) comes from the crankcase, and fuel is not injected until the piston rises and all ports are closed.

Two types of GDi are used in two-strokes: low-pressure air-assisted, and high-pressure. The former, developed by Orbital Engine Corporation of Australia (now Orbital Corporation) injects a mixture of fuel and compressed air into the combustion chamber. When the air expands it atomizes the fuel. The Orbital system is used in motor scooters manufactured by Aprilia SR50Aprilia, Piaggio, Peugeot and Kymco, in outboard motors manufactured by Mercury and Tohatsu, and in personal watercraft manufactured by Bombardier Recreational Products.

The high-pressure direct injector for two-stroke engines was developed in the early 1990s by Ficht GmbH of Kirchseeon Germany. Outboard Marine Corporation (OMC) licensed the technology in 1995 and introduced it on a production outboard engine in 1996.[57][58] OMC purchased a controlling interest in Ficht in 1998.[59] Beset by extensive warranty claims for its Ficht outboards and prior and concurrent management-financial problems, OMC declared bankruptcy in December 2000 and the engine manufacturing portion and brands (Evinrude Outboard Motors and Johnson Outboards), including the Ficht technology, were purchased by Bombardier Recreational Products in 2001.[60][61]

Evinrude introduced the E-Tec system, an improvement to the Ficht fuel injection, in 2003, based on U.S. patent 6,398,511.[62] In 2004, Evinrude received the EPA Clean Air Excellence Award for their outboards utilizing the E-Tec system.[63] The E-Tec system has recently also been adapted for use in performance two-stroke snowmobiles.

Yamaha also has a high-pressure direct injection (HPDI) system for two-stroke outboards. It differs from the Ficht/E-Tec and Orbital direct injection systems because it uses a separate, belt driven, high-pressure, mechanical fuel pump to generate the pressure necessary for injection in a closed chamber. This is similar to most current 4-stroke automotive designs.

EnviroFit, a non-profit corporation sponsored by Colorado State University, has developed direct injection retrofit kits for two-stroke motorcycles in a project to reduce air pollution in Southeast Asia, using technology developed by Orbital Corporation of Australia.[64] The World Health Organization says air pollution in Southeast Asia and the Pacific causes 537,000 premature deaths each year. The 100-million two-stroke taxis and motorcycles in that part of the world are a major cause.[65][66]

Drawbacks

Although Direct Injection provides more power and efficiency, a carbon build-up occurs in the intake valves that over time reduces the airflow to the cylinders, and therefore reduces power. Fuel contains various detergents and can keep the intakes clean. When fuel is no longer being sprayed in the intake valves, small amounts of dirt from intake air cakes on the intake walls, even with air filters that prevent most of the dirt from entering the cylinder.[67] This build-up can become severe enough that a piece can break off and has been known to burn holes in catalytic converters.[68] It can also cause sporadic ignition failures.[68] These problems have been known for some time and technologies have been improved to reduce the carbon build-up.

Future

Twin-fuel engines

Code named Bobcat, the new twin-fuel engine from Ford is based on a 5.0L V8 engine block but uses E85 cylinder injection and gasoline port injection. The engine was co-developed with Ethanol Boosting Systems, LLC of Cambridge, Massachusetts, which calls its trademarked process DI Octane Boost. The direct injection of ethanol increases the octane of regular gasoline from 88-91 octane to the maximum 130 octane. The Bobcat project was unveiled to the United States Department of Energy and the SAE International in April 2009.[69][70]

Formula One

Amongst other power unit changes, part of the rule changes for the 2014 season, Direct Injection has been made compulsory, With regulation 5.10.2 stating 'There may only be one direct injector per cylinder and no injectors are permitted upstream of the intake valves or downstream of the exhaust valves.' [71]

Emissions

In 2013, a research by TÜV NORD found that although gasoline direct injection engines dramatically reduce CO2 emissions, they release about 1,000 times more particles classified by the World Health Organization as harmful than traditional petrol engines and 10 times more than new diesel engines. The release happens because direct injection results in uneven burning of fuel due to uneven mixing of fuel and air (stratification) and because direct injection engines operate with a higher pressure in their cylinders than the older engines.

This pollution can be prevented with a relatively inexpensive filter that can significantly reduce the emissions of particles. However, fitting the filter is not mandatory yet.[72]

See also

References

  1. ↑ "Skyactiv-G Engine; Skyactiv Technology". Mazda. Retrieved 25 September 2013.
  2. ↑ "The Stratified Charge Engine" (PDF). Renault. Retrieved 25 September 2013.
  3. ↑ "Honda Releases Stream Absolute Equipped with Newly Developed 2.0L DOHC i-VTEC I Engine" (Press release). Honda. 27 November 2007. Retrieved 25 September 2013.
  4. ↑ Gerard Hartmann (August 5, 2007). "Les moteurs et aéroplanes Antoinette" [Antoinette engines and aeroplanes] (PDF) (in French). Retrieved November 7, 2012.
  5. ↑ Lindh, Björn-Eric (1992). Scania fordonshistoria 1891-1991 (Scania: vehicle history 1891-1991) (in Swedish). Streiffert. ISBN 91-7886-074-1.
  6. ↑ Olsson, Christer (1987). Volvo – Lastbilarna igår och idag (Volvo – the trucks yesterday and today) (in Swedish). Norden. ISBN 91-86442-76-7.
  7. 1 2 "van Basshuysen, Richard (April 2007). Ottomotoren mit Direkteinspritzung. Verfahren, Systeme, Entwicklung, Potenzial". Friedr. Vieweg & Sohn Verlag, GWV Fachverlage GmbH, Wiesbaden. April 2007. Retrieved 2012-01-19.
  8. ↑ "The Advent of Fuel Injection". http://autouniversum.wordpress.com/. 2010-09-25. Retrieved 2013-11-19. External link in |publisher= (help)
  9. ↑ Peery, Kelton Michels (1975). The Heintz straticharge engine: modifications I through V. Department of Mechanical Engineering, Stanford University. p. 18. Retrieved 25 September 2013.
  10. ↑ Weiss, Merkel Friedman (1979). Design and prototype evaluation of a fuel-control system for the straticharge 6 engine. Department of Mechanical Engineering. p. 2. Retrieved 25 September 2013.
  11. ↑ Weiss, p. 25.
  12. ↑ Weiss, p. 26.
  13. ↑ "Detroit's "Total Revolution"". Time. 19 March 19799. Retrieved 25 September 2013. Check date values in: |date= (help)
  14. ↑ Csere, Csaba (June 2004). "Will gasoline direct injection finally make it?". Car and Driver. Retrieved 25 September 2013.
  15. ↑ "Mose Knows: Direct-Injected 302 ProcoEngine". Ford Racing. 18 August 2011. Retrieved 25 September 2013.
  16. ↑ Parker, Akweli (2009-12-02). "How Direct Injection Engines Work". HowStuffWorks.com. Retrieved 2013-09-09.
  17. ↑ "Latest MMC technologies and near-future goals: GDI". Mitsubishi Motors. Retrieved 2012-06-21.
  18. ↑ "European Launch for GDI CARISMA", Mitsubishi Motors press release, August 29, 1997 Archived December 10, 2006 at the Wayback Machine
  19. ↑ Wan, Mark. "Green Engine Technology - Petrol Engines". AutoZine Technical Schoo. Retrieved 2012-06-21.
  20. ↑ "Mitsubishi Motors Adds World First V6 3.5-liter GDI Engine to Ultra-efficiency GDI Series", Mitsubishi Motors press release, April 16, 1997 Archived October 1, 2009 at the Wayback Machine
  21. ↑ "GDI1 engine production tops 1,000,000 unit mark", Mitsubishi Motors press release, September 11, 2001 Archived January 13, 2009 at the Wayback Machine
  22. ↑ "GDI-ASG Pistachio" (Press release). Mitsubishi Motors PR. 1999-09-28. Archived from the original on 2009-03-28. Retrieved 2013-09-08.
  23. ↑ "The Nissan VG/VQ-series V6 Guide". AutoSpeed. Retrieved 2010-07-29.
  24. ↑ "30_39-Jfl/'Ý,,v" (PDF). Retrieved 2009-07-17.
  25. ↑ "D4English". Alflash.com.ua. Retrieved 2009-05-16.
  26. ↑ Visnic, Bill (1996-09-01). "Direct-injection coming for the masses". Wardsautoworld.com. Retrieved 2012-06-21.
  27. ↑ "Toyota Avensis review". Fleetnews.co.uk. 2000-08-01. Retrieved 2012-06-21.
  28. ↑ "Improving the Environmental Performance of Internal Combustion Engines ― Engine". Toyota. 1999-02-22. Archived from the original on September 9, 2009. Retrieved 2009-08-21.
  29. ↑ Crouch, Jonathan. "Renault Megane Cabriolet 1997-2003". uk.cars.yahoo.com. Archived from the original on 2011-07-18. Retrieved 2012-06-21.
  30. ↑ Wan, Mark (2000). "Lean Burn Engine". Autozine Technical School. Retrieved 2010-11-14.
  31. ↑ Yamaguchi, Jack (2000-02-01). "Mitsubishi's new GDI applications". Automotive Engineering International (highbeam). Retrieved 2013-09-09.
  32. ↑ Beecham, Matthew (2007-12-07). "Research Analysis: a review of gasoline direct injection systems". Just-Auto. Retrieved 2013-09-09.
  33. 1 2 "Mitsubishi Motors and PSA Peugeot Citroen Reach Agreement on GDI Engine Technical Cooperation" (Press release). Mitsubishi Motors. 1999-01-12. Archived from the original on 2009-01-12. Retrieved 2013-09-08.
  34. ↑ "Mitsubishi Motors Supplies Hyundai Motor Co. with GDI Technology for New V8 GDI Engine" (Press release). Mitsubishi Motors. 1999-04-28. Archived from the original on 2009-01-12. Retrieved 2013-09-08.
  35. ↑ Motor Business Japan. Economist Intelligence Unit. 1997. p. 128. Retrieved 2013-09-09. Hyundai is second only to Volvo among companies borrowing the technology from Mitsubishi.
  36. ↑ "Japan Quarterly" 46. Asahi Shimbun. 1999: 22. Retrieved 2013-09-09.
  37. 1 2 "Not so nuts". AutoSpeed. 2000-09-19. Retrieved 2013-09-09.
  38. ↑ Schmitt, Peter A. (2004). Langenscheidt Fachwörterbuch Technik und angewandte Wissenschaften. Langenscheidt Fachverlag. p. 235. ISBN 978-3-86117-480-6. Retrieved 2012-06-21.
  39. ↑ "Mitsubishi's new GFI Applications". Automotive Engineering International (Society of Automotive Engineers) 108: 146. 2000. Retrieved 2013-09-09. Mitsubishi has also entered a GDI development pact with PSA of France for Peugeot cars
  40. ↑ "news 2002". italiaspeed.com. Retrieved 2007-10-24.
  41. 1 2 3 Ford of Europe showcases most extensive range ever at the 2002 Paris Show, Media.ford.com, 2002-09-26.
  42. ↑  Rex Roy, Detroit Editor. "2003 BMW 7-Series Review". The Car Connection. Retrieved 2009-08-21.
  43. ↑ "BMW Unveils New Direct-Injection, Bi-Turbo Inline Six". Green Car Congress. Retrieved 2009-08-21.
  44. ↑ "Inside BMW's Latest Powertrain Technologies". Edmunds.com. Archived from the original on May 12, 2006. Retrieved May 12, 2006.
  45. 1 2 "Honda Worldwide, World News; News Release". World.honda.com. 2003-11-27. Retrieved 2009-07-17.
  46. ↑ "Isuzu Direct-Injection V6", Popular Science, 2003 Archived August 28, 2006 at the Wayback Machine
  47. ↑ "BMW Direct Injection in 335i turbo engine". Bmwusa.com. Archived from the original on June 7, 2009. Retrieved 2011-12-02.
  48. ↑ "BMW officially announces new N54 Turbo Engine". Leftlanenews.com. Retrieved 2010-07-29.
  49. ↑ "The Unofficial Mercedes-Benz Weblog". eMercedesBenz. 2006-02-24. Retrieved 2009-08-21.
  50. ↑ "Audi R8 FSI® Technology".
  51. ↑ Audi R8 (road car)
  52. 1 2 3 "Ford to equip half a million vehicles with EcoBoost engine technology for up to 20% better fuel economy". Ford Motor Company. 2008-01-06. Retrieved 2010-11-14.
  53. ↑ "First Look: 2009 BMW X6 xDrive50i". Insideline.com. 2008-01-15. Retrieved 2010-07-29.
  54. ↑ "First look at Ferrari's all-new '458 Italia' supercar". Motor Authority. Retrieved 2009-07-28.
  55. ↑ Edmunds, Dan (2009-06-17). "Ford's Taurus Recovery Plan Gets Some Teeth". Edmunds Inside Line. Retrieved 2010-11-14.
  56. ↑ Abuelsamid, Sam (2009-11-13). "New Hyundai 2.4-liter GDI four-cylinder makes 200 hp in 2011 Sonata". AOL Inc. Retrieved 2010-11-14.
  57. ↑ "OMC and Ficht announce strategic alliance". PR Newswire. 1995-07-24. Retrieved 2010-11-14.
  58. ↑ "OMC Ficht fuel injection engines hit the market". PR Newswire. 1996-07-31. Retrieved 2010-11-14.
  59. ↑ "Marriage Made in Boat Heaven". Sarasota Herald-Tribune. 1998-12-26.
  60. ↑ Renken, Tim (2001-03-26). "Canadian, German Companies Buy Assets of Waukegan, Ill., Boating Company". St. Louis Post-Dispatch. Retrieved 2010-11-14.
  61. ↑ Ajootian, Caroline (March 2001). "OMC Bankruptcy Sets Consumers Adrift". Boat/US Magazine. Retrieved 2010-11-14.
  62. ↑ "United States Patent 6398511". USPTO Patent Full-Text and Image Database. 2000-08-18. Retrieved 2011-09-17.
  63. ↑ "2004 Clean Air Excellence Awards Recipients". U.S. EPA. Archived from the original on October 13, 2010. Retrieved 2010-11-14.
  64. ↑ Envirofit works to retrofit the Philippines Archived April 28, 2007 at the Wayback Machine
  65. ↑ "Ernasia project - Asian City Air Pollution Data Are Released". Ernasia.org. Retrieved 2010-11-14.
  66. ↑ Herro, Alana (2007-08-01). "Retrofitting Engines Reduces Pollution, Increases Incomes". Worldwatch Institute. Retrieved 2010-11-14.
  67. ↑ Goodwin, Antuan. "What's so great about direct injection? (ABCs of Car Tech)". cnet.com. Retrieved 31 March 2014.
  68. 1 2 Mark Holthoff, Matt Landish. "Direct Injection Fouls Some Early Adopters". edmunds.ciom. Retrieved 31 March 2014.
  69. ↑ "Sneak Peek! Ford's "Bobcat" Dual Fuel Engine". News.pickuptrucks.com. 2009-06-08. Retrieved 2010-11-14.
  70. ↑ Wood, Colum (2009-06-10). "Ford’s Twin-Fuel ‘Bobcat’ Engine Could Replace Power Stroke Diesels". autoguide.com. Retrieved 2010-11-14.
  71. ↑ "Formula One 2014 Technical Regulations".
  72. ↑ http://www.ft.com/intl/cms/s/0/60b7cc8c-56b2-11e3-ab12-00144feabdc0.html#axzz2mCT3PQ6p |title=Latest petrol engines ‘more harmful than traditional designs’ |publisher=ft.com |date=2013-11-27 |accessdate=2013-12-01
This article is issued from Wikipedia - version of the Saturday, February 13, 2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.