Pulse code cab signaling

SEPTA cab signal display for the 4-aspect PRR system using position light aspects

Pulse code cab signaling is a form of cab signaling technology developed in the United States by the Union Switch and Signal corporation for the Pennsylvania Railroad in the 1920s. The 4-aspect system widely adopted by the PRR and its successor railroads has become the dominant railroad cab signaling system in North America with versions of the technology also being adopted in Europe and rapid transit systems. In its home territory on former PRR successor Conrail owned lines and on railroads operating under the NORAC Rulebook it is known simply as Cab Signaling System or CSS.

History

Pulse code CSS antenna mounted under the pilot of an SRNJ diesel locomotive

In 1922 the Interstate Commerce Commission issued a ruling requiring trains to be equipped with automatic train stop technology to operate at 80 mph or greater. The Pennsylvania Railroad decided to use this as an opportunity to implement a signaling technology that could improve both safety and operational efficiency by displaying a signal continuously in the locomotive cab. The task was assigned to Union Switch and Signal corporation, the PRR's preferred signal supplier.

The first test installation [1] between Sunbury and Lewistown, PA in 1923 used the tracks as an inductive loop coupled to the locomotive’s receiver. The system had two 60 Hz signals. The break-sensing “track” signal was fed down one rail towards the oncoming train and crossed through its wheels, returning in the other rail. The pickup just ahead of the wheels would sum the approaching current from one side with the returning current on the other. The externally returned ”loop” signal was fed into and out of the mid tap of a resistor across each end of the track circuit. The pickup would sum the approaching current on each side as it carried on past to the far end of the track. This signal was shifted 90 degrees from the other. The signals were applied one or both continuously to give Approach or Clear aspects while no signal was a Restricting aspect. The test installation eliminated wayside block signals, and trains relied solely on cab signals.

For its next installation,[1] on the Northern Central line between Baltimore, MD and Harrisburg, PA in 1926 (1927?), the PRR tested another variation of cab signals which dropped the loop signal and switched to 100 Hz for the track signal. The pivotal change was that now it would come on above Restricting merely as a carrier and 1.25 to 3 Hz on-off pulsing of it would be used as a code to convey the aspects. The presence of the carrier alone was not meaningful, no pulsing would still mean a Restricting aspect. This new system allowed four signal aspects: Restricting; Approach; Approach (next signal at) Medium (speed); and Clear. Initially the cab signaling system only acted as a form of automatic train stop where the engineer would have to acknowledge any drop in the cab signal to a more restrictive aspect to prevent the brakes from automatically applying. Later, passenger engines were upgraded with speed control which enforced the rulebook speed associated with each cab signal (Clear = No Restriction, Approach Medium = 45 mph, Approach = 30 mph, Restricting = 20 mph).

Over time the PRR installed cab signals over much of its eastern system from Pittsburgh to Philadelphia, New York to Washington. This system was then inherited by Conrail and Amtrak and various commuter agencies running on former PRR territory such as SEPTA and New Jersey Transit. Because all trains running in cab signal territory had to be equipped with cab signals, most locomotives of the aforementioned roads were equipped with cab signal equipment. Due to the effect of interoperability lock in, the 4-aspect PRR cab signal system has become a de facto standard and almost all new cab signaling installations have been of this type or a compatible type.

Technical overview

US&S electro-mechanical pulse code generator unit generating 180ppm for a cab signal system

Basic operation

Pulse code cab signals work by sending metered pulses along an existing AC track circuit operating at some chosen carrier frequency. The pulses are detected via induction by a sensor hanging a few inches above the rail before the leading set of wheels. The codes are measured in pulses per minute and for the 4-aspect PRR system are set at 180 ppm for Clear, 120 ppm for Approach Medium, 75 ppm for Approach and 0 for Restricting. The pulse rates are chosen to avoid any one rate being a multiple of another leading to reflected harmonics causing false indications.[2]

The system is failsafe in that the lack of code would display a Restricting signal. The codes would be transmitted to the train from the block limit in front of it. This way if the rail was broken or another train entered the block, any codes would not reach the onrushing train and the cab signal would again display Restricting. Trains with an insufficient number of axles will not short out all of the cab signal current so that following trains might receive an incorrect aspect. Trains of this type must be given absolute block protection to the rear.

Where DC and 25 Hz AC electrification co-exist, the standard 100 Hz frequency is changed to 912⁄3Hz (next available M-G set frequency). This avoids even harmonics created by the return rail's DC traction current offsetting the AC return sine wave in the same rail.[3]

Enhancements for higher speeds

70 years after pulse code cab signals had been introduced, the 4 speed design was found to be insufficient for speeds not envisioned when the system was designed. The two most pressing problems were the use of high speed turnouts, which allowed trains to take a diverging route faster than the normal 30 or 45 mph covered by the existing cab signals. The introduction of Amtrak's Acela Express service with its 135 mph to 150 mph maximum speeds would also exceed the capabilities of the legacy signaling system and its 125 mph design speed.

To address the problem and avoid a complete rebuild of the signaling system, impair lower speed service, break backwards compatibility with existing cab signals or place too high a reliance on the human operator, an overlay pulse code system was devised for use on Amtrak's Northeast Corridor. By operating with a different carrier frequency of 250 Hz, additional pulse codes could be sent to the train without interfering with legacy 100 Hz codes. By carefully designing the overlay codes, backwards compatibility could be maintained so that any train unable to detect the new codes would never receive a signal more favorable than had it would otherwise detect. In addition to the use of 250 Hz codes, a 5th, 270ppm code was incorporated from rapid transit and Long Island Rail Road use.

The mapping of codes to speeds is as follows:

100 Hz code 250 Hz code Cab Signal Aspect Cab Signal Speed Notes
180 180 Clear 150 mph Legacy Units get Clear (125 mph)
180 --- Clear 125 mph Original PRR System Code
270 270 Clear 100 mph Used for high density signaling.
270 --- Cab Speed 60 mph Used for high density signaling. Compatible with LIRR ASC System
120 120 Cab Speed 80 mph Used for most high speed turnouts. Legacy Units get Approach Medium.
120 --- Approach Medium 45 mph Original PRR System Code
75 --- Approach 30 mph Original PRR System Code
0 --- Restricting 20 mph Failsafe state. Original PRR System Code



Trains with the ability to get the 250 Hz codes get upgraded speeds on track sections with speeds greater than 125 mph and on 80 mph high speed turnouts. Trains without simply travel at the slower speeds. The 270ppm code does break backwards compatibility with the 4-code system, but is only in use around New York Penn Station as part of a high density signaling upgrade. The 270ppm code and 60 mph speed were chosen to be compatible with the cab signals installed on the Long Island Rail Road trains that also use Penn Station.

Cab display unit

Cab signals are presented to the locomotive by means of a cab signal display unit. The earliest CDUs consisted of miniature signals of the type visible along the track, back lit by light bulbs. These could be found in both color light and position light varieties depending on the railroad's native signaling system. Modern CDUs on passenger trains are often integrated with the speedometer, as cab signals now serve a speed control function. On trains equipped with automatic train control functionality failure to properly acknowledge a restrictive cab signal change results in a 'penalty brake application', as does failure to observe the cab signal speed limit.

Usage

Current lines using the 100hz 4-aspect PRR cab signal system

Modern Amtrak cab signal display using colorized position light signals. This unit is compatible with the ACSES overlay system and is currently displaying a RESTRICTING aspect with the speed limit of 20mph displayed below.

Related North American pulse code systems

European pulse code systems

References

  1. 1 2 Allison, L.R. (July 1951). "A Modern Cab Signaling and Train Control System for Railroads". US&S. Transactions of the AIEE 70 (1): 232-239.
  2. ↑ Pierro, Jr., Joseph J. (March 13, 1984). "Patent US4437056 - Cab signal test set for automatically testing the pickup coils and checking an amplifier of cab signal equipment".
  3. ↑ Aspray, William (July 1991). "Edwin L. Harder, an oral history conducted in 1991 by William Aspray, IEEE History Center, Hoboken, NJ, USA.". Engineering & Technology History Wiki (ethw.org). Retrieved August 25, 2015.
  4. ↑ "Automatic Train Operation on the Victoria Line". Tubeprune.


This article is issued from Wikipedia - version of the Friday, December 18, 2015. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.