Air–fuel ratio meter

An air–fuel ratio meter monitors the air–fuel ratio of an internal combustion engine. Also called air–fuel ratio gauge, air–fuel meter, or air–fuel gauge. It reads the voltage output of an oxygen sensor, sometimes also called lambda sensor, whether it be from a narrow band or wide band oxygen sensor.

The original narrow-band oxygen sensors became factory installed standard in the late 1970s and early 1980s. In recent years, a newer and much more accurate wide-band sensor, though more expensive, has become available.

Most stand-alone narrow-band meters have 10 LEDs and some have more. Also common, narrow band meters in round housings with the standard mounting 2 1/16" and 2 5/8" diameters, as other types of car 'gauges'. These usually have 10 or 20 LEDs. Analogue 'needle' style gauges are also available.

As stated above, there are wide-band meters that stand alone or are mounted in housings. Nearly all of these show the air–fuel ratio on a numeric display, since the wide-band sensors provide a much more accurate reading. And since they use more accurate electronics, these meters are more expensive.

Benefits of air–fuel ratio metering

Determining the condition of the oxygen sensor: A malfunctioning oxygen sensor will result in air–fuel ratios that respond more slowly to changing engine conditions. A damaged or defective sensor may lead to increased fuel consumption and increased pollutant emissions as well as decreased power and throttle response. Most engine management systems will detect a defective oxygen sensor.
Reducing emissions: Keeping the air–fuel mixture near the stoichiometric ratio of 14.7:1 (for gasoline engines) allows the catalytic converter to operate at maximum efficiency.
Fuel economy: An air–fuel mixture leaner than the stoichiometric ratio will result in near-optimal fuel mileage, costing less per distance traveled and producing the least amount of CO₂ emissions. However, from the factory, cars are designed to operate at the stoichiometric ratio (rather than as lean as possible while remaining drivable) to maximize the efficiency and life of the catalytic converter. While it may be possible to run smoothly at mixtures leaner than the stoichiometric ratio, manufacturers must focus on emissions and especially catalytic converter life (which must now be 100,000 miles (160,000 km) on new vehicles ) as a higher priority due to U.S. EPA regulations.
Engine performance: Carefully mapping out air–fuel ratios throughout the range of rpm and manifold pressure will maximize power output in addition to reducing the risk of detonation.

Lean mixtures improve the fuel economy but also cause sharp rises in the amount of nitrogen oxides (NOX). If the mixture becomes too lean, the engine may fail to ignite, causing misfire and a large increase in unburned hydrocarbon (HC) emissions. Lean mixtures burn hotter and may cause rough idle, hard starting and stalling, and can even damage the catalytic converter, or burn valves in the engine. The risk of spark knock/engine knocking (detonation) is also increased when the engine is under load.

Mixtures that are richer than stoichiometric allow for greater peak engine power when using vaporized liquid fuel due to the mixture not being able to reach a perfectly homogenized state so extra fuel is added to ensure all oxygen is burned producing maximum power. The ideal mixture in this type of operation depends on the individual engine. For example, engines with forced induction such as turbochargers and superchargers typically require a richer mixture under wide open throttle than naturally aspirated engines. Forced induction engines can be catastrophically damaged by burning too lean for too long. The leaner the air–fuel mixture, the higher the combustion temperature is inside the cylinder. Too high a temperature will destroy an engine – melting the pistons and valves. This can happen if you port the head and/or manifolds or increase boost without compensating by installing larger or more injectors, and/or increasing the fuel pressure to a sufficient level. Conversely, engine performance can be lessened by increasing fuelling without increasing air flow into the engine. Furthermore, if an engine is leaned to the point where its exhaust gas temperature starts to fall, its cylinder head temperature will also fall. This is only recommended in the cruising configuration, never when accelerating hard, but is becoming increasingly popular in aviation circles, where the appropriate engine monitoring gauges are fitted and the fuel air mixture can be manually adjusted.^[1]

Cold engines also typically require more fuel and a richer mixture when first started (see: cold start injector), because fuel does not vaporize as well when cold and therefore requires more fuel to properly "saturate" the air. Rich mixtures also burn slower and decrease the risk of spark knock/engine knocking (detonation) when the engine is under load. However, rich mixtures sharply increase carbon monoxide (CO) emissions.

Oxygen sensor types

Oxygen sensors are installed in the exhaust system of the vehicle, attached to the engine's exhaust manifold, and measure the ratio of the air–fuel mixture.

As mentioned above, there are two types of sensors available: narrow band and wide band. Narrow-band sensors were the first to be introduced. The wide-band sensor was introduced much later.

A narrow-band sensor has a nonlinear output, with ranges from 0.10v to 1.0v with .450 being ideal. Narrow-band sensors are temperature-dependent. If the exhaust gases become warmer, the output voltage in the lean area will rise, and in the rich area it will be lowered. Consequently, a sensor, without pre-heating, has a lower lean-output and a higher rich-output, possibly even exceeding 1 volt. The influence of temperature on voltage is smaller in the lean mode than in the rich mode.

A "cold" engine makes the computer change the fuel air ratio so the output voltage of the o2 sensor switches between about 100 and 850/900 mV and after a while the sensor may output a switch voltage between about 200 and 700/750 mV, for turbocharged cars even less.

The engine control unit (ECU) when operating in "closed loop" tends to maintain zero oxygen (thus a stoichiometric balance), wherein the air–fuel mixture is approximately 14.7 times the mass of air to fuel for gasoline. This ratio maintains a "neutral" engine performance (lower fuel consumption yet decent engine power and minimal pollution).

The average level of the sensor is near to 450 mV. Since catalytic coverters need a cycling a/f ratio the oxygen sensor is not allowed to hold a fixed voltage, the ECU controls the engine by providing the mixture between lean (and rich) in such a sufficiently fast manner by means of shorter (or longer) time of signal to injectors, so the average level becomes as stated about 450 mV.

A wide-band sensor, on the other hand, has a very linear output, 0–5 V, and is requires a much hotter running temperature.

Which type of air–fuel ratio meter to be used

If the purpose of the air–fuel ratio meter is to detect also an existing or possible problem with the sensor above of checking the general mixture and performance, a narrow band air-fuel ratio meter is sufficient.

In high-performance tuning applications, the wide-band system is desirable.

References

↑ http://www.vansairforce.com/community/showthread.php?t=75132

External links

Airfuelratiometers.com, including illustrated information.

Automotive engine

Part of the Automobile series

Basic terminology	Compression ratio Crank Cylinder Dead centre Diesel engine Dry sump Engine balance Engine configuration Engine displacement Engine knocking Firing order Hydrolock Petrol engine Power band Redline Spark-ignition engine Stroke Stroke ratio Wet sump

Main components	Connecting rod Crankcase Crankpin Crankshaft Crossflow cylinder head Crossplane Cylinder bank Cylinder block Cylinder head Flywheel Head gasket Hypereutectic piston Main bearing Piston Piston ring Reverse-flow cylinder head Starter ring gear Sump

Valvetrain	Cam Cam follower Camshaft Desmodromic valve Hydraulic tappet Multi-valve Overhead camshaft Overhead valve Pneumatic valve springs Poppet valve Pushrod Rocker arm Sleeve valve Tappet Timing belt Timing mark Valve float Variable valve timing

Aspiration	Air filter Blowoff valve Boost controller Butterfly valve Centrifugal-type supercharger Cold air intake Dump valve Electronic throttle control Forced induction Inlet manifold Intake Intercooler Manifold vacuum Naturally aspirated engine Ram-air intake Scroll-type supercharger Short ram air intake Supercharger Throttle Throttle body Turbocharger Twin-turbo Variable-geometry turbocharger Variable-length intake manifold Warm air intake

Fuel system	Carburetor Common rail Direct injection Fuel filter Fuel injection Fuel pump Fuel tank Gasoline direct injection Indirect injection Injection pump Lean-burn Stratified charge engine Turbo fuel stratified injection Unit injector

Ignition	Contact breaker Magneto Distributor Electrical ballast High tension leads Ignition coil Spark plug Wasted spark

Electrics and engine management	Air–fuel ratio meter Alternator Automatic Performance Control Car battery (lead–acid battery) Crankshaft position sensor Dynamo Drive by wire Electronic control unit Engine control unit Engine coolant temperature sensor Glow plug Idle air control actuator MAP sensor Mass flow sensor Oxygen sensor Starter motor Throttle position sensor

Exhaust system	Automobile emissions control Catalytic converter Diesel particulate filter Exhaust manifold Glasspack Muffler

Engine cooling	Air cooling Antifreeze (ethylene glycol) Core plug Electric fan Fan belt Radiator Thermostat Water cooling Viscous fan (fan clutch)

Other components	Balance shaft Block heater Combustion chamber Cylinder head porting Gasket Motor oil Oil filter Oil pump Oil sludge PCV valve Seal Synthetic oil Underdrive pulleys

Portal Category

Sensors

Acoustic, sound, vibration	Geophone Hydrophone Lace Sensor Microphone Seismometer

Automotive, transportation	Air–fuel ratio meter Blind spot monitor Crankshaft position sensor Curb feeler Defect detector Engine coolant temperature sensor Hall effect sensor MAP sensor Mass flow sensor Omniview technology Oxygen sensor Parking sensors Radar gun Speed sensor Speedometer Throttle position sensor Tire-pressure monitoring system Torque sensor Transmission fluid temperature sensor Turbine speed sensor Variable reluctance sensor Vehicle speed sensor Water sensor Wheel speed sensor

Chemical	Breathalyzer Carbon dioxide sensor Carbon monoxide detector Catalytic bead sensor Chemical field-effect transistor Electrochemical gas sensor Electrolyte–insulator–semiconductor sensor Electronic nose Fluorescent chloride sensors Holographic sensor Hydrocarbon dew point analyzer Hydrogen sensor Hydrogen sulfide sensor Infrared point sensor Ion selective electrode Microwave chemistry sensor Nitrogen oxide sensor Nondispersive infrared sensor Olfactometer Optode Oxygen sensor Pellistor pH glass electrode Potentiometric sensor Redox electrode Smoke detector Zinc oxide nanorod sensor

Electric, magnetic, radio	Current sensor Electroscope Galvanometer Hall effect sensor Hall probe Magnetic anomaly detector Magnetometer MEMS magnetic field sensor Metal detector Planar Hall sensor Radio direction finder Test light

Environment, weather, moisture	Actinometer Bedwetting alarm Ceilometer Dew warning Electrochemical gas sensor Fish counter Frequency domain sensor Gas detector Hook gauge evaporimeter Humistor Hygrometer Leaf sensor Psychrometer Pyranometer Pyrgeometer Rain gauge Rain sensor SNOTEL Snow gauge Soil moisture sensor Stream gauge Tide gauge Weather radar

Flow, fluid velocity	Air flow meter Anemometer Flow sensor Gas meter Mass flow sensor Water metering

Ionising radiation, subatomic particles	Bubble chamber Cloud chamber Geiger counter Neutron detection Particle detector Scintillation counter Scintillator Wire chamber

Navigation instruments	Airspeed indicator Altimeter Attitude indicator Depth gauge Fluxgate compass Gyroscope Inertial navigation system Inertial reference unit Magnetic compass MHD sensor Ring laser gyroscope Turn coordinator Variometer Vibrating structure gyroscope Yaw-rate sensor

Position, angle, displacement	Accelerometer Auxanometer Capacitive displacement sensor Capacitive sensing Gravimeter Inclinometer Integrated circuit piezoelectric sensor Laser rangefinder Laser surface velocimeter Lidar Linear encoder Linear variable differential transformer Liquid capacitive inclinometers Odometer Photoelectric sensor Piezoelectric accelerometer Position sensor Rate sensor Rotary encoder Rotary variable differential transformer Selsyn Sudden Motion Sensor Tachometer Tilt sensor Ultrasonic thickness gauge Variable reluctance sensor Velocity receiver

Optical, light, imaging	Charge-coupled device Contact image sensor Electro-optical sensor Flame detector Infrared Kinetic inductance detector LED as light sensor Light-addressable potentiometric sensor Nichols radiometer Optical fiber Photodetector Photodiode Photoelectric sensor Photoionization detector Photomultiplier Photoresistor Photoswitch Phototransistor Phototube Position sensitive device Scintillometer Shack–Hartmann wavefront sensor Single-photon avalanche diode Superconducting nanowire single-photon detector Transition edge sensor Tristimulus colorimeter Visible-light photon counter Wavefront sensor

Pressure	Barograph Barometer Boost gauge Bourdon gauge Hot-filament ionization gauge Ionization gauge McLeod gauge Oscillating U-tube Permanent Downhole Gauge Piezometer Pirani gauge Pressure gauge Pressure sensor Tactile sensor Time pressure gauge

Force, density, level	Bhangmeter Force gauge Hydrometer Level sensor Load cell Magnetic level gauge Nuclear density gauge Piezoelectric sensor Strain gauge Torque sensor Viscometer

Thermal, heat, temperature	Bimetallic strip Bolometer Calorimeter Exhaust gas temperature gauge Flame detection Gardon gauge Golay cell Heat flux sensor Infrared thermometer Microbolometer Microwave radiometer Net radiometer Quartz thermometer Resistance thermometer Silicon bandgap temperature sensor Special sensor microwave/imager Thermistor Thermocouple Thermometer

Proximity, presence	Alarm sensor Doppler radar Motion detector Occupancy sensor Passive infrared sensor Proximity sensor Reed switch Stud finder Touch switch Triangulation sensor Wired glove

Sensor technology	Active pixel sensor Back-illuminated sensor Biochip Biosensor Capacitance probe Carbon paste electrode Catadioptric sensor Digital sensors Displacement receiver Electromechanical film Electro-optical sensor Fabry–Pérot interferometer Fisheries acoustics Image sensor Image sensor format Inductive sensor Intelligent sensor Lab-on-a-chip Leaf sensor Machine vision Microelectromechanical systems Photoelasticity Quantum sensor Radar Ground-penetrating radar Synthetic aperture radar Radar tracker Sensor array Sensor fusion Sensor grid Sensor node Soft sensor Sonar Staring array Transducer Ultrasonic sensor Video sensor technology Visual sensor network Wheatstone bridge Wireless sensor network

Related	List of sensors

This article is issued from Wikipedia - version of the Wednesday, October 07, 2015. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.