Yttrium barium copper oxide

Yttrium barium copper oxide

Names
IUPAC name barium copper yttrium oxide
Other names YBCO, Y123, yttrium barium cuprate
Identifiers
CAS Registry Number	107539-20-8 Y
Properties
Chemical formula	YBa2Cu3O7
Molar mass	666.19 g/mol
Appearance	Black solid
Density	6.3 g/cm3[1][2]
Melting point	>1000 °C
Solubility in water	Insoluble
Structure
Crystal structure	Based on the perovskite structure.
Coordination geometry	Orthorhombic
Hazards
EU classification	Irritant (Xi)
Related compounds
Related high-Tc superconductors	La2-xSrxCuO4 (LSCO)
Related compounds	Yttrium(III) oxide Barium oxide Copper(II) oxide
Except where noted otherwise, data is given for materials in their standard state (at 25 °C (77 °F), 100 kPa)
Y verify (what is: Y/N?)
Infobox references

Yttrium barium copper oxide, often abbreviated YBCO, is a family of crystalline chemical compounds, famous for displaying "high-temperature superconductivity". It includes the first material ever discovered to become superconducting above the boiling point of liquid nitrogen (77 K) at about 90 K. Many YBCO compounds have the general formula YBa₂Cu₃O_7-x (also known as Y123), although materials with other Y:Ba:Cu ratios exist, such as YBa₂Cu₄O_y (Y124) or Y₂Ba₄Cu₇O_y (Y247).

History

In April 1986, Georg Bednorz and Karl Müller, working at IBM in Zurich, discovered that certain semiconducting oxides became superconducting at relatively high temperature. In particular, the lanthanum barium copper oxide which becomes superconducting at 35 K. It is an oxygen deficient perovskite-related material that proved promising. In 1987, Bednorz and Müller were jointly awarded the Nobel Prize in Physics for this work.

Building on that, M.K. Wu and his graduate students, Ashburn and Torng^[3] at the University of Alabama in Huntsville in 1987, and Paul Chu and his students at the University of Houston in 1987 discovered YBCO has a critical temperature (T_c) of 93 K. (The first samples were Y_1.2Ba_0.8CuO₄.) Their work led to a rapid succession of new high temperature superconducting materials, ushering in a new era in material science and chemistry.

YBCO was the first material to become superconducting above 77 K, the boiling point of liquid nitrogen. All materials developed before 1986 became superconducting only at temperatures near the boiling points of liquid helium (T_b = 4.2 K) or liquid hydrogen (T_b = 20.28 K) — the highest being Nb₃Ge at 23 K. The significance of the discovery of YBCO is the much lower cost of the refrigerant used to cool the material to below the critical temperature.

Synthesis

Relatively pure YBCO was first synthesized by heating a mixture of the metal carbonates at temperatures between 1000 to 1300 K.^[4][5]

4 BaCO₃ + Y₂(CO₃)₃ + 6 CuCO₃ + (1/2−x) O₂ → 2 YBa₂Cu₃O_7−x + 13 CO₂

Modern syntheses of YBCO use the corresponding oxides and nitrates.^[5]

The superconducting properties of YBa₂Cu₃O_7−x are sensitive to the value of x, its oxygen content. Only those materials with 0 ≤ x ≤ 0.65 are superconducting below T_c, and when x ~ 0.07 the material superconducts at the highest temperature of 95 K,^[5] or in highest magnetic fields: 120 T for B perpendicular and 250 T for B parallel to the CuO₂ planes.^[6]

In addition to being sensitive to the stoichiometry of oxygen, the properties of YBCO are influenced by the crystallization methods used. Care must be taken to sinter YBCO. YBCO is a crystalline material, and the best superconductive properties are obtained when crystal grain boundaries are aligned by careful control of annealing and quenching temperature rates.

Numerous other methods to synthesize YBCO have developed since its discovery by Wu and his coworkers, such as chemical vapor deposition (CVD),^[4][5] sol-gel,^[7] and aerosol^[8] methods. These alternative methods, however, still require careful sintering to produce a quality product.

However, new possibilities have been opened since the discovery that trifluoroacetic acid (TFA), a source of fluorine, prevents the formation of the undesired barium carbonate (BaCO₃). Routes such as CSD (chemical solution deposition) have opened a wide range of possibilities, particularly in the preparation of long length YBCO tapes.^[9] This route lowers the temperature necessary to get the correct phase to around 700 °C. This, and the lack of dependence on vacuum, makes this method a very promising way to get scalable YBCO tapes.

Structure

Part of the lattice structure of yttrium barium copper oxide

YBCO crystallises in a defect perovskite structure consisting of layers. The boundary of each layer is defined by planes of square planar CuO₄ units sharing 4 vertices. The planes can sometimes be slightly puckered.^[4] Perpendicular to these CuO₂ planes are CuO₄ ribbons sharing 2 vertices. The yttrium atoms are found between the CuO₂ planes, while the barium atoms are found between the CuO₄ ribbons and the CuO₂ planes. This structural feature is illustrated in the figure to the right.

More details

Although YBa₂Cu₃O₇ is a well-defined chemical compound with a specific structure and stoichiometry, materials with fewer than seven oxygen atoms per formula unit are non-stoichiometric compounds. The structure of these materials depends on the oxygen content. This non-stoichiometry is denoted by the x in the chemical formula YBa₂Cu₃O_7-x. When x = 1, the O(1) sites in the Cu(1) layer are vacant and the structure is tetragonal. The tetragonal form of YBCO is insulating and does not superconduct. Increasing the oxygen content slightly causes more of the O(1) sites to become occupied. For x < 0.65, Cu-O chains along the b axis of the crystal are formed. Elongation of the b axis changes the structure to orthorhombic, with lattice parameters of a = 3.82, b = 3.89, and c = 11.68 Å. Optimum superconducting properties occur when x ~ 0.07, i.e., almost all of the O(1) sites are occupied, with few vacancies.

In experiments where other elements are substituted at the Cu and Ba sites evidence has shown that conduction occurs in the Cu(2)O planes while the Cu(1)O(1) chains act as charge reservoirs, which provide carriers to the CuO planes. However, this model fails to address superconductivity in the homologue Pr123 (praseodymium instead of yttrium).^[10] This (conduction in the copper planes) confines conductivity to the a-b planes and a large anisotropy in transport properties is observed. Along the c axis, normal conductivity is 10 times smaller than in the a-b plane. For other cuprates in the same general class, the anisotropy is even greater and inter-plane transport is highly restricted.

Furthermore, the superconducting length scales show similar anisotropy, in both penetration depth (λ_ab ≈ 150 nm, λ_c ≈ 800 nm) and coherence length, (ξ_ab ≈ 2 nm, ξ_c ≈ 0.4 nm). Although the coherence length in the a-b plane is 5 times greater than that along the c axis it is quite small compared to classic superconductors such as niobium (where ξ ≈ 40 nm). This modest coherence length means that the superconducting state is more susceptible to local disruptions from interfaces or defects on the order of a single unit cell, such as the boundary between twinned crystal domains. This sensitivity to small defects complicates fabricating devices with YBCO, and the material is also sensitive to degradation from humidity.

Superconductive properties

It is a Type-II superconductor.

Penetration depth : 120 nm in the ab plane, 800 nm along the c axis.

Coherence length : 2 nm in the ab plane, 0.4 nm along the c axis.

Properties of single crystals

The upper critical field is 120 T for B perpendicular and 250 T for B parallel to the CuO₂ planes.

Bulk properties

Bulk properties depend greatly on the manner of synthesis and treatment because of the effect on crystal size, alignment, and density and type of lattice defects.

Applications

Many possible applications of this and related high temperature superconducting materials have been discussed. For example, superconducting materials are finding use as magnets in magnetic resonance imaging, magnetic levitation, and Josephson junctions. (The most used material for power cables and magnets is BSCCO.)

YBCO has yet to be used in many applications involving superconductors for two primary reasons:

• First, although single crystals of YBCO have a very high critical current density, polycrystals have a very low critical current density: only a small current can be passed while maintaining superconductivity. This problem is due to crystal grain boundaries in the material. When the grain boundary angle is greater than about 5°, the supercurrent cannot cross the boundary. The grain boundary problem can be controlled to some extent by preparing thin films via CVD or by texturing the material to align the grain boundaries.
• A second problem limiting the use of this material in technological applications is associated with processing of the material. Oxide materials such as this are brittle, and forming them into wires by any conventional process does not produce a useful superconductor. (Unlike BSCCO, the powder-in-tube process does not give good results with YBCO.)

It should be noted that cooling materials to liquid nitrogen temperature (77 K) is often not practical on a large scale, although many commercial magnets are routinely cooled to liquid helium temperatures (4.2 K).

The most promising method developed to utilize this material involves deposition of YBCO on flexible metal tapes coated with buffering metal oxides. This is known as coated conductor. Texture (crystal plane alignment) can be introduced into the metal tape itself (the RABiTS process) or a textured ceramic buffer layer can be deposited, with the aid of an ion beam, on an untextured alloy substrate (the IBAD process). Subsequent oxide layers prevent diffusion of the metal from the tape into the superconductor while transferring the template for texturing the superconducting layer. Novel variants on CVD, PVD, and solution deposition techniques are used to produce long lengths of the final YBCO layer at high rates. Companies pursuing these processes include American Superconductor, Superpower (a division of Intermagnetics General Corp), Sumitomo, Fujikura, Nexans Superconductors, and European Advanced Superconductors. A much larger number of research institutes have also produced YBCO tape by these methods.

Commercialization

American Superconductor Corporation (AMSC)^[11] is producing the Amperium wire its second generation high temperature superconductor (HTS) wire ‘344 YBCO superconductors wire’.^[12] Amperium superconductor wire exhibits conductivity approximately 200 times that of copper wire of similar dimensions.^[13]

Surface modification of YBCO

Surface modification of materials has often led to new and improved properties. Corrosion inhibition, polymer adhesion and nucleation, preparation of organic superconductor/insulator/high-T_c superconductor trilayer structures, and the fabrication of metal/insulator/superconductor tunnel junctions have been developed using surface-modified YBCO.^[14]

These molecular layered materials are synthesized using cyclic voltammetry. Thus far, YBCO layered with alkylamines, arylamines, and thiols have been produced with varying stability of the molecular layer. It has been proposed that amines act as Lewis bases and bind to Lewis acidic Cu surface sites in YBa₂Cu₃O₇ to form stable coordination bonds.

Media

Like all superconductors, YBCO displays the Meissner effect. Below its critical temperature, YBCO becomes perfectly diamagnetic and excludes sufficiently weak magnetic fields from passing through it.^[4]

References

External links

• Diagram of YBCO structure
• New World Record For Superconducting Magnet 26.8T April 2007
• External MSDS Data Sheet (safety classifications) for YBCO.
• Superconductivity in everyday life : Interactive exhibition – little if any specific to YBCO.