Thyratron

Giant GE hydrogen thyratron, used in pulsed radars, next to miniature 2D21 thyratron used to trigger relays in jukeboxes

A thyratron is a type of gas-filled tube used as a high-power electrical switch and controlled rectifier. Because of the gas fill, thyratrons can handle much greater currents than similar hard-vacuum tubes, since electron multiplication occurs in the ionized gas, the phenomenon called Townsend discharge. Gases used include mercury vapor, xenon, neon, and (in special high-voltage applications or applications requiring very short switching times) hydrogen.[1] Unlike a vacuum tube (valve), a thyratron cannot be used to amplify signals linearly.

In the 1920s, thyratrons were derived from early vacuum tubes such as the UV-200, which contained a small amount of argon gas to increase its sensitivity as a radio signal detector; and the German LRS Relay tube, which also contained argon gas. Gas rectifiers, which predated vacuum tubes, such as the argon-filled General Electric "Tungar bulb" and the Cooper-Hewitt mercury-pool rectifier, also provided an influence. Irving Langmuir and G. S. Meikle of GE are usually cited as the first investigators to study controlled rectification in gas tubes, about 1914. The first commercial thyratrons didn't appear until around 1928.

A solid-state device with similar operating characteristics is the thyristor, sometimes also known as the silicon controlled rectifier (SCR). The term "thyristor" was derived from a combination of "thyratron" and "transistor".[2] Since the 1960s thyristors have replaced thyratrons in most low- and medium-power applications.

Construction and operation

Most commonly used symbols on U.S.A. and on Europe of a thyratron (variations are usually related to the representation of the filament and the cathode)

A typical hot-cathode thyratron uses a heated filament cathode, completely contained within a shield assembly with a control grid on one open side, which faces the plate-shaped anode. In the off situation the voltage on the control grid is negative with respect to the cathode. When positive voltage is applied to the anode, no current flows. When the control electrode is made less negative, electrons from the cathode can travel to the anode because the positive attraction from the anode prevails over the negative repulsion caused by the slightly negative voltage on the control grid. The electrons will ionize the gas by collisions with the gas in the tube, and an avalanche effect results, causing an arc discharge between cathode and anode. The shield prevents ionized current paths that might form within other parts of the tube. The gas in a thyratron is typically at a fraction of the pressure of air at sea level; 15 to 30 millibars (1.5 to 3 kPa) is typical. For a cold-cathode thyratron the trigger voltage on the control grid will typically be positive, and a flash-over from control grid to cathode will initiate the arc discharge in the tube.

Both hot- and cold-cathode versions are encountered. A hot cathode is at an advantage, as ionization of the gas is made easier; thus, the tube's control electrode is more sensitive. Once turned on, the thyratron will remain on (conducting) as long as there is a significant current flowing through it. When the anode voltage or current falls to zero, the device switches off.

Applications

Rare Z806W relay tube used in elevators
Wynn-Williams' Scale-of-Two Counter using thyratrons. (With permission of the Cavendish Laboratory, University of Cambridge, UK.)

Low-power thyratrons (relay tubes and trigger tubes) were manufactured for controlling incandescent lamps, electromechanical relays or solenoids, for bidirectional counters, to perform various functions in Dekatron calculators, for voltage threshold detectors in RC timers, etc. Glow thyratrons were optimized for high gas-discharge light output or even phosphorized and used as self-displaying shift registers in large-format, crawling-text dot-matrix displays.

One miniature thyratron, the triode 6D4, found an additional use as a potent noise source, when operated as a diode (grid tied to cathode) in a transverse magnetic field.[3] Sufficiently filtered for "flatness" ("white noise") in a band of interest, such noise was used for testing radio receivers, servo systems and occasionally in analog computing as a random value source.

Medium-power thyratrons found applications in machine tool motor controllers, where thyratrons, operating as phase-controlled rectifiers, are utilized in the tool's armature regulator (zero to "base speed", "constant torque" mode) and in the tool's field regulator ("base speed" to about twice "base speed", "constant horsepower" mode). Examples include Monarch Machine Tool 10EE lathe, which used thyratrons from 1949 until solid-state devices replaced them in 1984.[4]

High-power thyratrons are still manufactured, and are capable of operation up to tens of kiloamperes (kA) and tens of kilovolts (kV). Modern applications include pulse drivers for pulsed radar equipment, high-energy gas lasers, radiotherapy devices, particle accelerators and in Tesla coils and similar devices. Thyratrons are also used in high-power UHF television transmitters, to protect inductive output tubes from internal shorts, by grounding the incoming high-voltage supply during the time it takes for a circuit breaker to open and reactive components to drain their stored charges. This is commonly called a crowbar circuit.

Thyratrons have been replaced in most low and medium-power applications by corresponding semiconductor devices known as thyristors (sometimes called silicon-controlled rectifiers, or SCRs) and triacs. However, switching service requiring voltages above 20 kV and involving very short risetimes remains within the domain of the thyratron.

Variations of the thyratron idea are the krytron, the sprytron, the ignitron, and the triggered spark gap, all still used today in special applications, such as nuclear weapons (krytron) and AC/DC-AC power transmission (ignitron).

Example of a small thyratron

R.C.A. brand 885 Triode Thyratron

The 885 is a small thyratron tube, using xenon gas. This device was used extensively in the timebase circuits of early oscilloscopes in the 1930s. It was employed in a circuit called a relaxation oscillator. During World War II small thyratrons, similar to the 885 were utilized in pairs to construct bistables, the "memory" cells used by early computers and code breaking machines. Thyratrons were also used for phase angle control of alternating current (AC) power sources in battery chargers and light dimmers, but these were usually of a larger current handling capacity than the 885. The 885 is a 2.5 volt, 5-pin based variant of the 884/6Q5.

Notes

  1. ↑ L. W. Turner (ed), Electronics Engineer's Reference Book, 4th ed. Newnes-Butterworth, London 1976 ISBN 0-408-00168-2, pages 7-177 and 7-180.
  2. ↑ http://home.roadrunner.com/~mathematikos/Etymology/thyristor.pdf
  3. ↑ "Sylvania: 6D4 Miniature triode thyratron data sheet" (PDF). Retrieved 25 May 2013.
  4. ↑ http://www.lathes.co.uk/monarch/page2.html Lathes.co.uk, retrieved 2012 July 27

References

External links