Tape correction (surveying)

In surveying, tape correction(s) refer(s) to correcting measurements for the effect of temperature and tension, catenary and to reduce measurement on the slope to the equivalent horizontal length. Not correcting for these effects gives rise to systematic errors as the effects act in a predictable manner which can be corrected by mathematical methods.

Correction due to incorrect tape length

Manufacturers of measuring tapes do not usually guarantee the exact length of tapes, and standardization is a process where a standard temperature and tension are determined at which the tape is the exact length. The nominal length of tapes can be affected by physical imperfections, stretching or wear. Constant use of tapes cause wear, tapes can become kinked and may be improperly repaired when breaks occur.

The correction due to tape length is given by:

C_L = M_L \pm Corr \times \frac {M_L}{N_L}

Where:

CL is the corrected length of the line to be measured or laid out;
ML is the measured length or length to be laid out;
NL is the nominal length of the tape as specified by its mark;
Corr is the <define here>.

Note that incorrect tape length introduces a systematic error that must be calibrated periodically.

Correction due to slope

\theta is the angle between the slope line and the horizontal line, s is the slope distance measured between two points on the slope line, h is the height of the slope.

When distances are measured along the slope, the equivalent horizontal distance may be determined by applying a slope correction.

The vertical slope angle of the length measured must be measured. (Refer to the figure on the other side) Thus,

  • For gentle slopes, m<20\%
C_h = \frac {h^2}{2s}
  • For steep slopes, 20\%\le m \le 30\%
C_h = \frac {h^2}{2s} + \frac {h^4}{8s^3}
  • For very steep slopes, m>30\%
C_h = s(1-\cos \theta)

Where:

C_h is the correction of measured slope distance due to slope;
\theta is the angle between the measured slope line and horizontal line;
s is the measured slope distance.

The correction C_h is subtracted from s to obtain the equivalent horizontal distance on the slope line:

d = s - C_h

Correction due to temperature

When measuring or laying out distances, the standard temperature of the tape and the temperature of the tape at time of measurement are usually different. A difference in temperature will cause the tape to lengthen or shorten, so the measurement taken will not be exactly correct. A correction can be applied to the measured length to obtain the correct length.

The correction of the tape length due to change in temperature is given by:

C_t = C \cdot L (T_m - T_s)

Where:

C_t is the correction to be applied to the tape due to temperature;
C is the coefficient of thermal expansion of the metal that forms the tape;
L is the length of the tape or length of the line measured.
T_m is the observed temperature of the tape at the time of measurement;
T_s is the standard temperature, when the tape is at the correct length, often 20 °C;

The correction C_t is added to L to obtain the corrected distance:

d = L + C_t

For common tape measurements, the tape used is a steel tape with coefficient of thermal expansion C equal to 0.000,011,6 units per unit length per degree Celsius change. This means that the tape changes length by 1.16 mm per 10 m tape per 10 °C change from the standard temperature of the tape. For a 30 meter long tape with standard temperature of 20 °C used at 40 °C, the change in length is 7 mm over the length of the tape.

Correction due to tension

Tension introduces error when the tape is pulled at a tension which differs from the standard tension used at standardization. The tape will stretch less than its standard length when a tension less than the standard tension is applied, making the tape too short.

The tape stretches in an elastic manner until it reaches its elastic limit when it will deform permanently and ruin the tape.

The correction due to tension is given by:

C_p = \frac{(P_m - P_s)L}{AE}

Where:

C_p is the elongation in tape length due to pull; or the correction to be applied due to applying a tension which differs from standard tension; meters;
P_m is the tension applied to the tape during measurement; Newtons;
P_s is the standard tension, when the tape is the correct length, often 50 Newtons; Newtons;
L is the measured or erroneous length of the line; meters
A is the cross-sectional area of the tape; square centimeters;
E is the modulus of elasticity of the tape material; Newtons per square centimeter;


The correction C_p is added to L to obtain the corrected distance:

d = L + C_p

The value for A is given by:

A = \frac {W}{(L)(U_w)}

Where:

W is the total weight of the tape; kilograms;
U_w is the unit weight of the tape; kilograms per cubic centimeter.

For steel tapes, the value for U_w is 7.866 \times 10^{-3} kg/cm^3.

Correction due to sag

A tape not supported along its length will sag and form a catenary between end supports. The correction due to sag must be calculated separately for each unsupported stretch separately and is given by:

C_s = \frac {{\omega}^2 L^3}{24P^2}

Where:

C_s is the correction applied to the tape due to sag; meters;
\omega is the weight of the tape per unit length; Newtons per meter;
L is the length between the two ends of the catenary; meters;
P is the tension or pull applied to the tape; Newtons.

A tape held in catenary will record a value larger than the correct measurement. Thus, the correction C_s is subtracted from L to obtain the corrected distance:

d = L - C_s

Note that the weight of the tape per unit length is equal to the weight of the tape divided by the length of the tape:

\omega = \frac {W}{L}

so: W = \omega L

Therefore, we can rewrite the formula for correction due to sag as:

C_s = \frac {W^2 L}{24 P^2}

Derivation (sag)

The general formula for a catenary formed by a tape supported only at its ends is

y = \frac{P}{\omega g} \cosh \left(\frac{x \omega g}{P}\right).

Here g is the gravitational acceleration. The arc length between two support points at x=-k/2 and x=+k/2 is found by usual methods via integration:

L = \int_{-k/2}^{+k/2} \sqrt{1+\left(dy/dx\right)^2} \, dx

For convenience set a=\frac{P}{\omega g}. The integrand is simplified as follows using hyperbolic function identities:

\sqrt{1+\left(dy/dx\right)^2} = \sqrt{1+\left(\frac{d}{dx}\left(a \cosh\left(\frac{x}{a}\right)\right)\right)^2} = \sqrt{1+\sinh^2\left(\frac{x}{a}\right)} = \cosh\left(\frac{x}{a}\right)

The tape length L is then found by integrating:

L = \int_{-k/2}^{+k/2} \cosh\left(\frac{x}{a}\right) dx = \left[a \sinh\left(\frac{x}{a}\right)\right]_{x=-k/2}^{x=+k/2} = \left(2a\right) \sinh\left(\frac{k}{2a}\right)

Now the correction for tape sag is the difference between the actual span between the supports, k, and the arc length of the tape's catenary, L. Call this correction \delta = k - L. The absolute value of this \delta correction is C_s above, the amount you would subtract from the tape measurement to get the true span distance.

A Taylor series expansion of \delta in terms of the quantity L is desired to give a good first approximation to the correction. In fact the first nonvanishing term in the Taylor series is cubic in L and the next nonvanishing term is to the fifth power of L. Thus a series expansion for \delta is reasonable. To this end we need to find an expression for \delta that contains L but not k. We already have an expression for L in terms of k, but now need to find the inverse function (for k in terms of L):

\frac{L}{2a} = \sinh\left(\frac{k}{2a}\right)
\sinh^{-1}\left(\frac{L}{2a}\right)= \frac{k}{2a}
k = \left(2a\right) \sinh^{-1}\left(\frac{L}{2a}\right)
\delta = k - L = \left(2a\right) \sinh^{-1}\left(\frac{L}{2a}\right) - L

Evaluating delta at L=0 yields zero, so there is no zero order term in the Taylor series. The first derivative of this function with respect to L is:

\frac{d\delta}{dL} = \frac{1}{\sqrt{\frac{L^2}{4 a^2}+1}}-1

Evaluated at L=0 it vanishes and so does not contribute a Taylor series term. The second derivative of \delta is:

\frac{d^2\delta}{{dL}^2} = -\frac{L}{4 a^2 \left(\frac{L^2}{4 a^2}+1\right)^{3/2}}

Again when evaluated at L=0 it vanishes. When evaluated at L=0 the third derivative survives however:

\frac{d^3\delta}{{dL}^3} = -\frac{ \left(8 a^3-4\text{aL}^2\right)}{\left(4 a^2+L^2\right)^{5/2} }

Thus the first surviving term in the Taylor series is:

\delta \cong \left[\frac{d^3\delta}{{dL}^3}\right]_{L=0} \frac{ L^3}{3!} = -\frac{1}{4a^2} \frac{L^3}{6} = \frac{-L^3}{24a^2} = \frac{-L^3 \omega^2 g^2}{24 P^2}

Notice that the variable P here is the tension on the cable, whereas above P is the mass whose gravitational force (mass times gravitational acceleration) equals the tension on the cable. The only conversion necessary then is to take P/g here and equate it to P above. Also this formula is the tape sag correction to be added to the measured distance, so the negative sign in front can be removed and the tape sag correction can be made instead by subtracting the absolute value as is done in the preceding section.

See also

References

Mostly in pdf: