Solar energy

Solar energy is radiant light and heat from the sun harnessed using a range of ever-evolving technologies such as solar heating, solar photovoltaics, solar thermal energy, solar architecture and artificial photosynthesis.^[1][2]

It is an important source of renewable energy and its technologies are broadly characterized as either passive solar or active solar depending on the way they capture and distribute solar energy or convert it into solar power. Active solar techniques include the use of photovoltaic systems, concentrated solar power and solar water heating to harness the energy. Passive solar techniques include orienting a building to the Sun, selecting materials with favorable thermal mass or light dispersing properties, and designing spaces that naturally circulate air.

In 2011, the International Energy Agency said that "the development of affordable, inexhaustible and clean solar energy technologies will have huge longer-term benefits. It will increase countries’ energy security through reliance on an indigenous, inexhaustible and mostly import-independent resource, enhance sustainability, reduce pollution, lower the costs of mitigating global warming, and keep fossil fuel prices lower than otherwise. These advantages are global. Hence the additional costs of the incentives for early deployment should be considered learning investments; they must be wisely spent and need to be widely shared".^[1]

Part of a series on Renewable energy
Biofuel Biomass Geothermal Hydropower Solar energy Tidal power Wave power Wind power
Topics by country

Energy from the Sun

The Earth receives 174 petawatts (PW) of incoming solar radiation (insolation) at the upper atmosphere.^[3] Approximately 30% is reflected back to space while the rest is absorbed by clouds, oceans and land masses. The spectrum of solar light at the Earth's surface is mostly spread across the visible and near-infrared ranges with a small part in the near-ultraviolet.^[4]

Earth's land surface, oceans and atmosphere absorb solar radiation, and this raises their temperature. Warm air containing evaporated water from the oceans rises, causing atmospheric circulation or convection. When the air reaches a high altitude, where the temperature is low, water vapor condenses into clouds, which rain onto the Earth's surface, completing the water cycle. The latent heat of water condensation amplifies convection, producing atmospheric phenomena such as wind, cyclones and anti-cyclones.^[5] Sunlight absorbed by the oceans and land masses keeps the surface at an average temperature of 14 °C.^[6] By photosynthesis green plants convert solar energy into chemical energy, which produces food, wood and the biomass from which fossil fuels are derived.^[7]

Yearly solar fluxes & human energy consumption
Solar	3,850,000 EJ	[8]
Wind	2,250 EJ	[9]
Biomass potential	~200 EJ	[10]
Primary energy use (2010)	539 EJ	[11]
Electricity (2010)	~67 EJ	[12]
1 Exajoule (EJ) is 1018 Joules or 278 billion kilowatt-hours (kW·h).

The total solar energy absorbed by Earth's atmosphere, oceans and land masses is approximately 3,850,000 exajoules (EJ) per year.^[8] In 2002, this was more energy in one hour than the world used in one year.^[13][14] Photosynthesis captures approximately 3,000 EJ per year in biomass.^[15] The technical potential available from biomass is from 100–300 EJ/year.^[10] The amount of solar energy reaching the surface of the planet is so vast that in one year it is about twice as much as will ever be obtained from all of the Earth's non-renewable resources of coal, oil, natural gas, and mined uranium combined,^[16]

Solar energy can be harnessed at different levels around the world, mostly depending on distance from the equator.^[17]

Early commercial adaption

In 1897, Frank Shuman, a U.S. inventor, engineer and solar energy pioneer built a small demonstration solar engine that worked by reflecting solar energy onto square boxes filled with ether, which has a lower boiling point than water, and were fitted internally with black pipes which in turn powered a steam engine. In 1908 Shuman formed the Sun Power Company with the intent of building larger solar power plants. He, along with his technical advisor A.S.E. Ackermann and British physicist Sir Charles Vernon Boys,^[18] developed an improved system using mirrors to reflect solar energy upon collector boxes, increasing heating capacity to the extent that water could now be used instead of ether. Shuman then constructed a full-scale steam engine powered by low-pressure water, enabling him to patent the entire solar engine system by 1912.

Shuman built the world’s first solar thermal power station in Maadi, Egypt, between 1912 and 1913. Shuman’s plant used parabolic troughs to power a 45–52 kilowatts (60–70 hp) engine that pumped more than 22,000 litres (4,800 imp gal; 5,800 US gal) of water per minute from the Nile River to adjacent cotton fields. Although the outbreak of World War I and the discovery of cheap oil in the 1930s discouraged the advancement of solar energy, Shuman’s vision and basic design were resurrected in the 1970s with a new wave of interest in solar thermal energy.^[19] In 1916 Shuman was quoted in the media advocating solar energy's utilization, saying:

We have proved the commercial profit of sun power in the tropics and have more particularly proved that after our stores of oil and coal are exhausted the human race can receive unlimited power from the rays of the sun.

—Frank Shuman, New York Times, July 2, 1916^[20]

Applications of solar technology

Solar energy refers primarily to the use of solar radiation for practical ends. However, all renewable energies, other than geothermal and tidal, derive their energy from the sun.

Solar technologies are broadly characterized as either passive or active depending on the way they capture, convert and distribute sunlight. Active solar techniques use photovoltaic panels, pumps, and fans to convert sunlight into useful outputs. Passive solar techniques include selecting materials with favorable thermal properties, designing spaces that naturally circulate air, and referencing the position of a building to the Sun. Active solar technologies increase the supply of energy and are considered supply side technologies, while passive solar technologies reduce the need for alternate resources and are generally considered demand side technologies.^[21] CSP-Stirling is known to have the highest efficiency of all solar technologies (around 30%, compared to solar PV's approximately 15%) and is predicted to be able to produce the cheapest energy among all renewable energy sources in high scale production and hot areas, semi-deserts, etc.

Architecture and urban planning

Sunlight has influenced building design since the beginning of architectural history.^[23] Advanced solar architecture and urban planning methods were first employed by the Greeks and Chinese, who oriented their buildings toward the south to provide light and warmth.^[24]

The common features of passive solar architecture are orientation relative to the Sun, compact proportion (a low surface area to volume ratio), selective shading (overhangs) and thermal mass.^[23] When these features are tailored to the local climate and environment they can produce well-lit spaces that stay in a comfortable temperature range. Socrates' Megaron House is a classic example of passive solar design.^[23] The most recent approaches to solar design use computer modeling tying together solar lighting, heating and ventilation systems in an integrated solar design package.^[25] Active solar equipment such as pumps, fans and switchable windows can complement passive design and improve system performance.

Urban heat islands (UHI) are metropolitan areas with higher temperatures than that of the surrounding environment. The higher temperatures are a result of increased absorption of the Solar light by urban materials such as asphalt and concrete, which have lower albedos and higher heat capacities than those in the natural environment. A straightforward method of counteracting the UHI effect is to paint buildings and roads white and plant trees. Using these methods, a hypothetical "cool communities" program in Los Angeles has projected that urban temperatures could be reduced by approximately 3 °C at an estimated cost of US$1 billion, giving estimated total annual benefits of US$530 million from reduced air-conditioning costs and healthcare savings.^[26]

Agriculture and horticulture

Agriculture and horticulture seek to optimize the capture of solar energy in order to optimize the productivity of plants. Techniques such as timed planting cycles, tailored row orientation, staggered heights between rows and the mixing of plant varieties can improve crop yields.^[27][28] While sunlight is generally considered a plentiful resource, the exceptions highlight the importance of solar energy to agriculture. During the short growing seasons of the Little Ice Age, French and English farmers employed fruit walls to maximize the collection of solar energy. These walls acted as thermal masses and accelerated ripening by keeping plants warm. Early fruit walls were built perpendicular to the ground and facing south, but over time, sloping walls were developed to make better use of sunlight. In 1699, Nicolas Fatio de Duillier even suggested using a tracking mechanism which could pivot to follow the Sun.^[29] Applications of solar energy in agriculture aside from growing crops include pumping water, drying crops, brooding chicks and drying chicken manure.^[30][31] More recently the technology has been embraced by vinters, who use the energy generated by solar panels to power grape presses.^[32]

Greenhouses convert solar light to heat, enabling year-round production and the growth (in enclosed environments) of specialty crops and other plants not naturally suited to the local climate. Primitive greenhouses were first used during Roman times to produce cucumbers year-round for the Roman emperor Tiberius.^[33] The first modern greenhouses were built in Europe in the 16th century to keep exotic plants brought back from explorations abroad.^[34] Greenhouses remain an important part of horticulture today, and plastic transparent materials have also been used to similar effect in polytunnels and row covers.

Transport and reconnaissance

Development of a solar-powered car has been an engineering goal since the 1980s. The World Solar Challenge is a biannual solar-powered car race, where teams from universities and enterprises compete over 3,021 kilometres (1,877 mi) across central Australia from Darwin to Adelaide. In 1987, when it was founded, the winner's average speed was 67 kilometres per hour (42 mph) and by 2007 the winner's average speed had improved to 90.87 kilometres per hour (56.46 mph).^[35] The North American Solar Challenge and the planned South African Solar Challenge are comparable competitions that reflect an international interest in the engineering and development of solar powered vehicles.^[36][37]

Some vehicles use solar panels for auxiliary power, such as for air conditioning, to keep the interior cool, thus reducing fuel consumption.^[38][39]

In 1975, the first practical solar boat was constructed in England.^[40] By 1995, passenger boats incorporating PV panels began appearing and are now used extensively.^[41] In 1996, Kenichi Horie made the first solar powered crossing of the Pacific Ocean, and the sun21 catamaran made the first solar powered crossing of the Atlantic Ocean in the winter of 2006–2007.^[42] There were plans to circumnavigate the globe in 2010.^[43]

In 1974, the unmanned AstroFlight Sunrise plane made the first solar flight. On 29 April 1979, the Solar Riser made the first flight in a solar-powered, fully controlled, man carrying flying machine, reaching an altitude of 40 feet (12 m). In 1980, the Gossamer Penguin made the first piloted flights powered solely by photovoltaics. This was quickly followed by the Solar Challenger which crossed the English Channel in July 1981. In 1990 Eric Scott Raymond in 21 hops flew from California to North Carolina using solar power.^[44] Developments then turned back to unmanned aerial vehicles (UAV) with the Pathfinder (1997) and subsequent designs, culminating in the Helios which set the altitude record for a non-rocket-propelled aircraft at 29,524 metres (96,864 ft) in 2001.^[45] The Zephyr, developed by BAE Systems, is the latest in a line of record-breaking solar aircraft, making a 54-hour flight in 2007, and month-long flights were envisioned by 2010.^[46]

A solar balloon is a black balloon that is filled with ordinary air. As sunlight shines on the balloon, the air inside is heated and expands causing an upward buoyancy force, much like an artificially heated hot air balloon. Some solar balloons are large enough for human flight, but usage is generally limited to the toy market as the surface-area to payload-weight ratio is relatively high.^[47]

Solar thermal

Solar thermal technologies can be used for water heating, space heating, space cooling and process heat generation.^[48]

Water heating

Solar hot water systems use sunlight to heat water. In low geographical latitudes (below 40 degrees) from 60 to 70% of the domestic hot water use with temperatures up to 60 °C can be provided by solar heating systems.^[49] The most common types of solar water heaters are evacuated tube collectors (44%) and glazed flat plate collectors (34%) generally used for domestic hot water; and unglazed plastic collectors (21%) used mainly to heat swimming pools.^[50]

As of 2007, the total installed capacity of solar hot water systems is approximately 154 thermal gigawatt (GW_th).^[51] China is the world leader in their deployment with 70 GW_th installed as of 2006 and a long-term goal of 210 GW_th by 2020.^[52] Israel and Cyprus are the per capita leaders in the use of solar hot water systems with over 90% of homes using them.^[53] In the United States, Canada and Australia heating swimming pools is the dominant application of solar hot water with an installed capacity of 18 GW_th as of 2005.^[21]

Heating, cooling and ventilation

In the United States, heating, ventilation and air conditioning (HVAC) systems account for 30% (4.65 EJ) of the energy used in commercial buildings and nearly 50% (10.1 EJ) of the energy used in residential buildings.^[54][55] Solar heating, cooling and ventilation technologies can be used to offset a portion of this energy.

Thermal mass is any material that can be used to store heat—heat from the Sun in the case of solar energy. Common thermal mass materials include stone, cement and water. Historically they have been used in arid climates or warm temperate regions to keep buildings cool by absorbing solar energy during the day and radiating stored heat to the cooler atmosphere at night. However, they can be used in cold temperate areas to maintain warmth as well. The size and placement of thermal mass depend on several factors such as climate, daylighting and shading conditions. When properly incorporated, thermal mass maintains space temperatures in a comfortable range and reduces the need for auxiliary heating and cooling equipment.^[56]

A solar chimney (or thermal chimney, in this context) is a passive solar ventilation system composed of a vertical shaft connecting the interior and exterior of a building. As the chimney warms, the air inside is heated causing an updraft that pulls air through the building. Performance can be improved by using glazing and thermal mass materials^[57] in a way that mimics greenhouses.

Deciduous trees and plants have been promoted as a means of controlling solar heating and cooling. When planted on the southern side of a building in the northern hemisphere or the northern side in the southern hemisphere, their leaves provide shade during the summer, while the bare limbs allow light to pass during the winter.^[58] Since bare, leafless trees shade 1/3 to 1/2 of incident solar radiation, there is a balance between the benefits of summer shading and the corresponding loss of winter heating.^[59] In climates with significant heating loads, deciduous trees should not be planted on the Equator facing side of a building because they will interfere with winter solar availability. They can, however, be used on the east and west sides to provide a degree of summer shading without appreciably affecting winter solar gain.^[60]

Water treatment

Solar distillation can be used to make saline or brackish water potable. The first recorded instance of this was by 16th-century Arab alchemists.^[61] A large-scale solar distillation project was first constructed in 1872 in the Chilean mining town of Las Salinas.^[62] The plant, which had solar collection area of 4,700 m² (51,000 sq ft), could produce up to 22,700 L (5,000 imp gal; 6,000 US gal) per day and operate for 40 years.^[62] Individual still designs include single-slope, double-slope (or greenhouse type), vertical, conical, inverted absorber, multi-wick, and multiple effect.^[61] These stills can operate in passive, active, or hybrid modes. Double-slope stills are the most economical for decentralized domestic purposes, while active multiple effect units are more suitable for large-scale applications.^[61]

Solar water disinfection (SODIS) involves exposing water-filled plastic polyethylene terephthalate (PET) bottles to sunlight for several hours.^[63] Exposure times vary depending on weather and climate from a minimum of six hours to two days during fully overcast conditions.^[64] It is recommended by the World Health Organization as a viable method for household water treatment and safe storage.^[65] Over two million people in developing countries use this method for their daily drinking water.^[64]

Solar energy may be used in a water stabilisation pond to treat waste water without chemicals or electricity. A further environmental advantage is that algae grow in such ponds and consume carbon dioxide in photosynthesis, although algae may produce toxic chemicals that make the water unusable.^[66][67]

Process heat

Solar concentrating technologies such as parabolic dish, trough and Scheffler reflectors can provide process heat for commercial and industrial applications. The first commercial system was the Solar Total Energy Project (STEP) in Shenandoah, Georgia, USA where a field of 114 parabolic dishes provided 50% of the process heating, air conditioning and electrical requirements for a clothing factory. This grid-connected cogeneration system provided 400 kW of electricity plus thermal energy in the form of 401 kW steam and 468 kW chilled water, and had a one-hour peak load thermal storage.^[68]

Evaporation ponds are shallow pools that concentrate dissolved solids through evaporation. The use of evaporation ponds to obtain salt from sea water is one of the oldest applications of solar energy. Modern uses include concentrating brine solutions used in leach mining and removing dissolved solids from waste streams.^[69]

Clothes lines, clotheshorses, and clothes racks dry clothes through evaporation by wind and sunlight without consuming electricity or gas. In some states of the United States legislation protects the "right to dry" clothes.^[70]

Unglazed transpired collectors (UTC) are perforated sun-facing walls used for preheating ventilation air. UTCs can raise the incoming air temperature up to 22 °C (40 °F) and deliver outlet temperatures of 45–60 °C (113–140 °F).^[71] The short payback period of transpired collectors (3 to 12 years) makes them a more cost-effective alternative than glazed collection systems.^[71] As of 2003, over 80 systems with a combined collector area of 35,000 square metres (380,000 sq ft) had been installed worldwide, including an 860 m² (9,300 sq ft) collector in Costa Rica used for drying coffee beans and a 1,300 m² (14,000 sq ft) collector in Coimbatore, India, used for drying marigolds.^[31]

Cooking

Solar cookers use sunlight for cooking, drying and pasteurization. They can be grouped into three broad categories: box cookers, panel cookers and reflector cookers.^[72] The simplest solar cooker is the box cooker first built by Horace de Saussure in 1767.^[73] A basic box cooker consists of an insulated container with a transparent lid. It can be used effectively with partially overcast skies and will typically reach temperatures of 90–150 °C (194–302 °F).^[74] Panel cookers use a reflective panel to direct sunlight onto an insulated container and reach temperatures comparable to box cookers. Reflector cookers use various concentrating geometries (dish, trough, Fresnel mirrors) to focus light on a cooking container. These cookers reach temperatures of 315 °C (599 °F) and above but require direct light to function properly and must be repositioned to track the Sun.^[75]

Electricity production

Solar power is the conversion of sunlight into electricity, either directly using photovoltaics (PV), or indirectly using concentrated solar power (CSP). CSP systems use lenses or mirrors and tracking systems to focus a large area of sunlight into a small beam. PV converts light into electric current using the photoelectric effect.

Commercial CSP plants were first developed in the 1980s. Since 1985 the eventually 354 MW SEGS CSP installation, in the Mojave Desert of California, is the largest solar power plant in the world. Other large CSP plants include the 150 MW Solnova Solar Power Station and the 100 MW Andasol solar power station, both in Spain. The 250 MW Agua Caliente Solar Project, in the United States, and the 221 MW Charanka Solar Park in India, are the world’s largest photovoltaic plants. Solar projects exceeding 1 GW are being developed, but most of the deployed photovoltaics are in small rooftop arrays of less than 5 kW, which are grid connected using net metering and/or a feed-in tariff.^[76]

Concentrated solar power

Concentrating Solar Power (CSP) systems use lenses or mirrors and tracking systems to focus a large area of sunlight into a small beam. The concentrated heat is then used as a heat source for a conventional power plant. A wide range of concentrating technologies exists; the most developed are the parabolic trough, the concentrating linear fresnel reflector, the Stirling dish and the solar power tower. Various techniques are used to track the Sun and focus light. In all of these systems a working fluid is heated by the concentrated sunlight, and is then used for power generation or energy storage.^[77]

Photovoltaics

A solar cell, or photovoltaic cell (PV), is a device that converts light into electric current using the photoelectric effect. The first solar cell was constructed by Charles Fritts in the 1880s.^[78] In 1931 a German engineer, Dr Bruno Lange, developed a photo cell using silver selenide in place of copper oxide.^[79] Although the prototype selenium cells converted less than 1% of incident light into electricity, both Ernst Werner von Siemens and James Clerk Maxwell recognized the importance of this discovery.^[80] Following the work of Russell Ohl in the 1940s, researchers Gerald Pearson, Calvin Fuller and Daryl Chapin created the crystalline silicon solar cell in 1954.^[81] These early solar cells cost 286 USD/watt and reached efficiencies of 4.5–6%.^[82] By 2012 available efficiencies exceed 20% and the maximum efficiency of research photovoltaics is over 40%.^[83]

Fuel production

Solar chemical processes use solar energy to drive chemical reactions. These processes offset energy that would otherwise come from a fossil fuel source and can also convert solar energy into storable and transportable fuels. Solar induced chemical reactions can be divided into thermochemical or photochemical.^[84] A variety of fuels can be produced by artificial photosynthesis.^[85] The multielectron catalytic chemistry involved in making carbon-based fuels (such as methanol) from reduction of carbon dioxide is challenging; a feasible alternative is hydrogen production from protons, though use of water as the source of electrons (as plants do) requires mastering the multielectron oxidation of two water molecules to molecular oxygen.^[86] Some have envisaged working solar fuel plants in coastal metropolitan areas by 2050 – the splitting of sea water providing hydrogen to be run through adjacent fuel-cell electric power plants and the pure water by-product going directly into the municipal water system.^[87] Another vision involves all human structures covering the earth's surface (i.e., roads, vehicles and buildings) doing photosynthesis more efficiently than plants.^[88]

Hydrogen production technologies been a significant area of solar chemical research since the 1970s. Aside from electrolysis driven by photovoltaic or photochemical cells, several thermochemical processes have also been explored. One such route uses concentrators to split water into oxygen and hydrogen at high temperatures (2,300–2,600 °C or 4,200–4,700 °F).^[89] Another approach uses the heat from solar concentrators to drive the steam reformation of natural gas thereby increasing the overall hydrogen yield compared to conventional reforming methods.^[90] Thermochemical cycles characterized by the decomposition and regeneration of reactants present another avenue for hydrogen production. The Solzinc process under development at the Weizmann Institute uses a 1 MW solar furnace to decompose zinc oxide (ZnO) at temperatures above 1,200 °C (2,200 °F). This initial reaction produces pure zinc, which can subsequently be reacted with water to produce hydrogen.^[91]

Energy storage methods

Thermal mass systems can store solar energy in the form of heat at domestically useful temperatures for daily or interseasonal durations. Thermal storage systems generally use readily available materials with high specific heat capacities such as water, earth and stone. Well-designed systems can lower peak demand, shift time-of-use to off-peak hours and reduce overall heating and cooling requirements.^[93][94]

Phase change materials such as paraffin wax and Glauber's salt are another thermal storage media. These materials are inexpensive, readily available, and can deliver domestically useful temperatures (approximately 64 °C or 147 °F). The "Dover House" (in Dover, Massachusetts) was the first to use a Glauber's salt heating system, in 1948.^[95]

Solar energy can be stored at high temperatures using molten salts. Salts are an effective storage medium because they are low-cost, have a high specific heat capacity and can deliver heat at temperatures compatible with conventional power systems. The Solar Two used this method of energy storage, allowing it to store 1.44 terajoules (400,000 kWh) in its 68 cubic metres (2,400 cu ft) storage tank with an annual storage efficiency of about 99%.^[96]

Off-grid PV systems have traditionally used rechargeable batteries to store excess electricity. With grid-tied systems, excess electricity can be sent to the transmission grid, while standard grid electricity can be used to meet shortfalls. Net metering programs give household systems a credit for any electricity they deliver to the grid. This is handled by 'rolling back' the meter whenever the home produces more electricity than it consumes. If the net electricity use is below zero, the utility then rolls over the kilowatt hour credit to the next month.^[97] Other approaches involve the use of two meters, to measure electricity consumed vs. electricity produced. This is less common due to the increased installation cost of the second meter. Most standard meters accurately measure in both directions, making a second meter unnecessary.

Pumped-storage hydroelectricity stores energy in the form of water pumped when energy is available from a lower elevation reservoir to a higher elevation one. The energy is recovered when demand is high by releasing the water, with the pump becoming a hydroelectric power generator.^[98]

Development, deployment and economics

Beginning with the surge in coal use which accompanied the Industrial Revolution, energy consumption has steadily transitioned from wood and biomass to fossil fuels. The early development of solar technologies starting in the 1860s was driven by an expectation that coal would soon become scarce. However, development of solar technologies stagnated in the early 20th century in the face of the increasing availability, economy, and utility of coal and petroleum.^[99]

The 1973 oil embargo and 1979 energy crisis caused a reorganization of energy policies around the world and brought renewed attention to developing solar technologies.^[100][101] Deployment strategies focused on incentive programs such as the Federal Photovoltaic Utilization Program in the US and the Sunshine Program in Japan. Other efforts included the formation of research facilities in the US (SERI, now NREL), Japan (NEDO), and Germany (Fraunhofer Institute for Solar Energy Systems ISE).^[102]

Commercial solar water heaters began appearing in the United States in the 1890s.^[103] These systems saw increasing use until the 1920s but were gradually replaced by cheaper and more reliable heating fuels.^[104] As with photovoltaics, solar water heating attracted renewed attention as a result of the oil crises in the 1970s but interest subsided in the 1980s due to falling petroleum prices. Development in the solar water heating sector progressed steadily throughout the 1990s and growth rates have averaged 20% per year since 1999.^[51] Although generally underestimated, solar water heating and cooling is by far the most widely deployed solar technology with an estimated capacity of 154 GW as of 2007.^[51]

The International Energy Agency has said that solar energy can make considerable contributions to solving some of the most urgent problems the world now faces:^[1]

The development of affordable, inexhaustible and clean solar energy technologies will have huge longer-term benefits. It will increase countries’ energy security through reliance on an indigenous, inexhaustible and mostly import-independent resource, enhance sustainability, reduce pollution, lower the costs of mitigating climate change, and keep fossil fuel prices lower than otherwise. These advantages are global. Hence the additional costs of the incentives for early deployment should be considered learning investments; they must be wisely spent and need to be widely shared.^[1]

In 2011, a report by the International Energy Agency found that solar energy technologies such as photovoltaics, solar hot water and concentrated solar power could provide a third of the world’s energy by 2060 if politicians commit to limiting climate change. The energy from the sun could play a key role in de-carbonizing the global economy alongside improvements in energy efficiency and imposing costs on greenhouse gas emitters. "The strength of solar is the incredible variety and flexibility of applications, from small scale to big scale".^[105]

We have proved ... that after our stores of oil and coal are exhausted the human race can receive unlimited power from the rays of the sun.

—Frank Shuman, New York Times, July 2, 1916^[20]

ISO standards

The International Organization for Standardization has established a number of standards relating to solar energy equipment. For example, ISO 9050 relates to glass in building while ISO 10217 relates to the materials used in solar water heaters.

Earth's mass conversion

Solar energy is converted into part of the mass of Earth by Photosynthetic pigments, so effectively the sun is sending matter that is stored on earth, with photosynthesizing organisms and energy as the intermediaries. In the case of Solar photovoltaics, they generally do not add to the mass of Earth because their energy is merely transmitted and subsequently radiated (as electricity or heat) which is not converted into chemical means to be stored on earth.

See also

Notes

References

External links

Wikimedia Commons has media related to Solar energy.

• "How do Photovoltaics Work?". NASA. 
• Renewable Energy: Solar at DMOZ
• Solar Energy Back in the Day - slideshow by Life magazine
• U.S. Solar Farm Map (1 MW or Higher)
• Online Resources Database on Solar in Developing Countries
• Online resources and news from the nonprofit American Solar Energy Society

Solar energy Concepts The Sun Insolation Solar radiation Active and passive solar energy Solar power Thermal Passive solar building design Solar water heating Solar chimney Solar air conditioning Thermal mass Solar pond Photovoltaics & related topics Photovoltaic effect Solar cell Polymer solar cell Nanocrystal solar cell Photovoltaic module (solar panel) Photovoltaic array (and systems) Photovoltaic power station Concentrated Heliostat Solar tracker Parabolic trough Solar power tower Experimental & proposed Solar updraft tower Solar-pumped laser Thermoelectric generator Solar chemical and artificial photosynthesis Space-based solar power Solar sail Magnetic sail Solar thermal rocket By country Australia Austria Albania Belgium Brazil Burma Canada China Czech Denmark Georgia Germany Greece India Israel Italy Japan Lithuania Mexico Morocco Netherlands New Zealand Pakistan Portugal Romania Saudi Arabia Somalia South Africa Spain Thailand Turkey Ukraine United Kingdom United States Yemen Distribution & uses Storage Thermal mass Thermal energy storage Phase change material Grid energy storage Adoption Feed-in tariff Net metering Financial incentives for photovoltaics Costs Applications Solar water heating Solar vehicle Electric aircraft Electric boat Solar balloon Other applications Agriculture and horticulture Greenhouse Polytunnel Row cover Solar-powered pump Building Passive solar building design Building-integrated photovoltaics Urban heat island Lighting Hybrid solar lighting Solar lamp Solar Tuki Light tube Daylighting Process heat Solar pond Solar furnace Salt evaporation pond Cooking Solar cooker Disinfection Solar water disinfection Soil solarization Desalination Solar still Desalination Water heating Solar water heating Solar combisystem Zero carbon solar controller See also Photovoltaics topics Solar power by country Renewable energy sources

Renewable energy by country Africa Algeria Ethiopia Kenya Morocco Seychelles Asia Afghanistan Armenia Bangladesh Bhutan Brunei China India Lebanon Nepal Pakistan Taiwan Thailand Europe Albania Czech Republic Finland Germany Greece Iceland Italy Lithuania Luxembourg Netherlands Norway Portugal Russia Spain United Kingdom (Scotland) North America Canada Honduras Mexico United States Oceania Australia New Zealand Tuvalu South America Argentina Brazil Chile Colombia Portals Energy Renewable energy Sustainable development

The Sun Internal structure Core Radiation zone Tachocline Convection zone Atmosphere Photosphere Supergranulation Granule Faculae Sunspot Chromosphere Plage Spicule Moreton wave Corona Transition region Coronal hole Coronal loop Coronal mass ejection Prominence Helmet streamer Variation Solar cycle List of solar cycles Solar maximum Solar minimum Wolf number Solar wind Flare Helioseismology Heliosphere Current sheet Termination shock Heliosheath Heliopause Bow shock Related topics Solar activity Solar astronomy Solar dynamo Eclipse Solar energy Solar physics Solar System Solar telescope Solar time Radiation Spectral class: G2V

Natural resources Air Pollution / quality Ambient standards (USA) Index health Indoor developing nations Law Clean Air Act (USA) Ozone depletion Emissions Airshed Trading Deforestation (REDD) Energy Law Resources Fossil fuels (peak oil) Geothermal Nuclear Solar sunlight shade Tidal Wave Wind Land Arable Degradation Law property Management habitat conservation Minerals mining law sand peak rights Soil conservation fertility health resilience Use planning reserve Life Biodiversity Bioprospecting Biosphere Bushfood Bushmeat Fisheries law management Food Forests genetic resources law management Game law Gene bank Herbalist plants Marine conservation Non-timber forest products Rangeland Seed bank Wildlife conservation management Wood Water Types / location Aquifer storage and recovery Drinking Fresh Groundwater pollution recharge remediation Hydrosphere Ice bergs glacial polar Irrigation Rain harvesting Stormwater Surface water Wastewater reclaimed Aspects Desalination Floods Law Leaching Sanitation Conflict Conservation Pollution Privatization Quality Right Resources management policy Related Commons common-pool enclosure global tragedy theory Economics ecological Ecosystem services Exploitation overexploitation Management adaptive Natural capital accounting Nature reserve Systems ecology Urban ecology Wilderness Resource Conflict (perpetuation) Curse Extraction Nationalism Renewable / Non-renewable Portals Agriculture and Agronomy Energy Environment Fishing Forestry Mining Water Category agencies law management ministries organizations Colleges Commons