Skyscraper

For other uses, see Skyscraper (disambiguation).
Burj Khalifa, the tallest skyscraper in the world since 2010, with a height of 829.8 m.

A skyscraper is a tall, continuously habitable building of over 40-50 floors, mostly designed for office, commercial and residential use. A skyscraper can also be called a high-rise, but the term skyscraper is often used for buildings higher than 150 m (492 ft). For buildings above a height of 300 m (984 ft), the term Supertall can be used, while skyscrapers reaching beyond 600 m (1,969 ft) are classified as Megatall.[1]

One common feature of skyscrapers is having a steel framework that supports curtain walls. These curtain walls either bear on the framework below or are suspended from the framework above, rather than load-bearing walls of conventional construction. Some early skyscrapers have a steel frame that enables the construction of load-bearing walls taller than of those made of reinforced concrete. Modern skyscrapers' walls are not load-bearing and most skyscrapers are characterized by large surface areas of windows made possible by the concept of steel frame and curtain walls. However, skyscrapers can have curtain walls that mimic conventional walls and a small surface area of windows. Modern skyscrapers often have a tubular structure, and are designed to act like a hollow cylinder to resist lateral loads (wind, seismic, etc.). To appear more slender, allow less wind exposure and to transmit more daylight to the ground, many skyscrapers have a design with setbacks.

Definition

A relatively big building may be considered a skyscraper if it protrudes well above its built environment and changes the overall skyline. The maximum height of structures has progressed historically with building methods and technologies and thus what is today considered a skyscraper is taller than before. The Burj Khalifa is the tallest building in the world. Skyscrapers let us conserve space allowing us to build up instead of out.

High-rise buildings are considered shorter than skyscrapers. There is no clear definition of any difference between a tower block and a skyscraper though a building lower than about thirty stories is not likely to be a skyscraper and a building with fifty or more stories is certainly a skyscraper.[2]

The term "skyscraper" was first applied to buildings of steel framed construction of at least 10 stories in the late 19th century, a result of public amazement at the tall buildings being built in major cities like Chicago, New York City, Philadelphia, Detroit, and St. Louis.[3] The first steel frame skyscraper was the Home Insurance Building (originally 10 stories with a height of 42 m or 138 ft) in Chicago, Illinois in 1885. Some point to Philadelphia's 10-story Jayne Building (1849–50) as a proto-skyscraper, or to New York's seven-floor Equitable Life Assurance Building, built in 1870, for its innovative use of a kind of skeletal frame, but such designation depends largely on what factors are chosen. Even the scholars making the argument find it to be purely academic.[4][5]

The structural definition of the word skyscraper was refined later by architectural historians, based on engineering developments of the 1880s that had enabled construction of tall multi-story buildings. This definition was based on the steel skeleton—as opposed to constructions of load-bearing masonry, which passed their practical limit in 1891 with Chicago's Monadnock Building.

Wikiquote has quotations related to: Skyscraper
What is the chief characteristic of the tall office building? It is lofty. It must be tall. The force and power of altitude must be in it, the glory and pride of exaltation must be in it. It must be every inch a proud and soaring thing, rising in sheer exaltation that from bottom to top it is a unit without a single dissenting line.
Louis Sullivan's The Tall Office Building Artistically Considered (1896)

The Emporis Standards Committee defines a high-rise building as "a multi-story structure between 35–100 meters tall, or a building of unknown height from 12–39 floors"[6] and a skyscraper as "a multi-story building whose architectural height is at least 100 m or 330 ft."[7] Some structural engineers define a highrise as any vertical construction for which wind is a more significant load factor than earthquake or weight. Note that this criterion fits not only high-rises but some other tall structures, such as towers.

The word skyscraper often carries a connotation of pride and achievement. The skyscraper, in name and social function, is a modern expression of the age-old symbol of the world center or axis mundi: a pillar that connects earth to heaven and the four compass directions to one another.[8]

A loose convention of some in the United States and Europe draws the lower limit of a skyscraper at 150 m or 490 ft.[9]

History

The Two Towers of Bologna in the 12th century reached 97.2 m (319 ft) in height.
The 16th-century city of Shibam consisted entirely of over 500 high-rise tower houses.

Pre-19th century

Until the 19th century, buildings of over six stories were rare, as having great numbers of stairs to climb was impractical for inhabitants, and water pressure was usually insufficient to supply running water above 50 m (164 ft).

The tallest building in ancient times was the 146 m (479 ft) Great Pyramid of Giza in ancient Egypt, built in the 26th century BC. It was not surpassed in height for thousands of years, the 14th century AD Lincoln Cathedral being conjectured by many to have exceeded it.[10] The latter in turn was not surpassed until the 555-foot (169 m) Washington Monument in 1884. However, being uninhabited, none of these structures actually comply with the modern definition of a skyscraper.

High-rise apartments flourished in classical antiquity. Ancient Roman insulae in imperial cities reached 10 and more stories.[11] Beginning with Augustus (r. 30 BC-14 AD), several emperors attempted to establish limits of 20–25 m for multi-story buildings, but met with only limited success.[12][13] Lower floors were typically occupied by shops or wealthy families, the upper rented to the lower classes.[11] Surviving Oxyrhynchus Papyri indicate that seven-story buildings existed in provincial towns such as in 3rd century AD Hermopolis in Roman Egypt.[14]

The skylines of many important medieval cities had large numbers of high-rise urban towers, built by the wealthy for defense and status. The residential Towers of 12th century Bologna numbered between 80 to 100 at a time, the tallest of which is the 97.2 m (319 ft) high Asinelli Tower. A Florentine law of 1251 decreed that all urban buildings be immediately reduced to less than 26 m.[15] Even medium-sized towns of the era are known to have proliferations of towers, such as the 72 up to 51 m height in San Gimignano.[15]

The medieval Egyptian city of Fustat housed many high-rise residential buildings, which Al-Muqaddasi in the 10th century described as resembling minarets. Nasir Khusraw in the early 11th century described some of them rising up to 14 stories, with roof gardens on the top floor complete with ox-drawn water wheels for irrigating them.[16] Cairo in the 16th century had high-rise apartment buildings where the two lower floors were for commercial and storage purposes and the multiple stories above them were rented out to tenants.[17] An early example of a city consisting entirely of high-rise housing is the 16th-century city of Shibam in Yemen. Shibam was made up of over 500 tower houses,[18] each one rising 5 to 11 stories high,[19] with each floor being an apartment occupied by a single family. The city was built in this way in order to protect it from Bedouin attacks.[18] Shibam still has the tallest mudbrick buildings in the world, with many of them over 30 m (98 ft) high.[20]

An early modern example of high-rise housing was in 17th-century Edinburgh, Scotland, where a defensive city wall defined the boundaries of the city. Due to the restricted land area available for development, the houses increased in height instead. Buildings of 11 stories were common, and there are records of buildings as high as 14 stories. Many of the stone-built structures can still be seen today in the old town of Edinburgh. The oldest iron framed building in the world, although only partially iron framed, is The Flaxmill (also locally known as the "Maltings"), in Shrewsbury, England. Built in 1797, it is seen as the "grandfather of skyscrapers”, since its fireproof combination of cast iron columns and cast iron beams developed into the modern steel frame that made modern skyscrapers possible. In 2013 funding was confirmed to convert the derelict building into offices.[21]

Oriel Chambers, Liverpool. The world's first glass curtain walled building. The stone mullions are decorative.
The Wainwright Building, a 10-story red brick office building in St. Louis, Missouri, built in 1891

Early skyscrapers

Main article: Early skyscrapers

In 1852 Elisha Otis introduced the safety elevator, allowing convenient and safe passenger movement to upper floors. Another crucial development was the use of a steel frame instead of stone or brick, otherwise the walls on the lower floors on a tall building would be too thick to be practical. An early development in this area was Oriel Chambers in Liverpool. Designed by local architect Peter Ellis in 1864, the building was the world's first iron-framed, glass curtain-walled office building. It was only 5 floors high.[22][23][24] Further developments led to the world's first skyscraper, the ten-story Home Insurance Building in Chicago, built in 1884–1885.[25] While its height is not considered very impressive today, it was at that time. The architect, Major William Le Baron Jenney, created a load-bearing structural frame. In this building, a steel frame supported the entire weight of the walls, instead of load-bearing walls carrying the weight of the building. This development led to the "Chicago skeleton" form of construction. In addition to the steel frame, the Home Insurance Building also utilized fireproofing, elevators, and electrical wiring, key elements in most skyscrapers today.[26]

Burnham and Root's 1889 Rand McNally Building in Chicago, 1889, was the first all-steel framed skyscraper,[27] while Louis Sullivan's Wainwright Building in St. Louis, Missouri, 1891, was the first steel-framed building with soaring vertical bands to emphasize the height of the building and is therefore considered by some to be the first true skyscraper.

Most early skyscrapers emerged in the land-strapped areas of Chicago and New York City toward the end of the 19th century. A land boom in Melbourne, Australia between 1888–1891 spurred the creation of a significant number of early skyscrapers, though none of these were steel reinforced and few remain today. Height limits and fire restrictions were later introduced. London builders soon found building heights limited due to a complaint from Queen Victoria, rules that continued to exist with few exceptions until the 1950s. Concerns about aesthetics and fire safety had likewise hampered the development of skyscrapers across continental Europe for the first half of the twentieth century. With some notable exceptions, like the 1898 Witte Huis (White House) in Rotterdam; the Royal Liver Building in Liverpool, completed in 1911 and 90 m (300 ft) high;[28] the 1924 Marx House in Düsseldorf, Germany; the 17-story Kungstornen (Kings' Towers) in Stockholm, Sweden, which were built 1924–25,[29] the 15-story Edificio Telefónica in Madrid, Spain, built in 1929; the 26-story Boerentoren in Antwerp, Belgium, built in 1932; and the 31-story Torre Piacentini in Genoa, Italy, built in 1940).

After an early competition between Chicago and New York City for the world's tallest building, New York took the lead by 1895 with the completion of the American Surety Building, leaving New York with the title of the world's tallest building for many years. New York City developers competed among themselves, with successively taller buildings claiming the title of "world's tallest" in the 1920s and early 1930s, culminating with the completion of the Chrysler Building in 1930 and the Empire State Building in 1931, the world's tallest building for forty years. The first completed World Trade Center tower became the world's tallest building in 1972. However, it was soon overtaken by the Sears Tower (now Willis Tower) in Chicago within two years. The Sears Tower stood as the world's tallest building for 24 years, from 1974 until 1998, until it was edged out by Petronas Twin Towers in Kuala Lumpur, which held the title for six years.

Modern skyscrapers

The Empire State Building in New York City. Completed in 1931, it was the tallest building in the world for nearly 40 years.

Modern skyscrapers are built with steel or reinforced concrete frameworks and curtain walls of glass or polished stone. They use mechanical equipment such as water pumps and elevators. From the 1930s onwards, skyscrapers began to appear around the world - also in Latin America (such as São Paulo, Rio de Janeiro, Buenos Aires, Santiago, Lima, Caracas, Bogotá, Mexico City) and in Asia (Tokyo, Shanghai, Hong Kong, Manila, Singapore, Mumbai, Seoul, Kuala Lumpur, Taipei, Bangkok).

Immediately after World War II, the Soviet Union planned eight massive skyscrapers, with seven of them actually getting built until 1953, dubbed the "Seven Sisters of Moscow". Other skyscrapers in the style of Socialist Classicism were erected in East Germany (Frankfurter Tor), Poland (PKiN), Ukraine (Hotel Ukrayina), Latvia (Academy of Sciences) and other countries. The western countries of Europe also began to permit taller skyscrapers than before WW2, such as Madrid during the 1950s (Gran Vía). Finally, skyscrapers also began to be constructed in cities of Africa, the Middle East and Oceania (mainly Australia) from the late 1950s on.

Skyscraper projects after World War II typically rejected the classical designs of the early skyscrapers, instead embracing the uniform international style; many older skyscrapers were redesigned to suit contemporary tastes or even demolished - such as New York's Singer Building, once the world's tallest skyscraper.

German architect Ludwig Mies van der Rohe became one of the world's most renowned architects in the second half of the 20th century. He conceived of the glass façade skyscraper[30] and, along with Norwegian Fred Severud,[31] he designed the Seagram Building in 1958, a skyscraper that is often regarded as the pinnacle of the modernist high-rise architecture.[32]

After the Great Depression skyscrapers construction suffered a hiatus for over thirty years due to economic problems. A revival occurred with structural innovations that transformed the industry,[33] making it possible for people to live and work in "cities in the sky".[34]

In the early 1960s structural engineer Fazlur Khan realized that the dominating rigid steel frame structure was not the only system apt for tall buildings, marking a new era of skyscraper construction in terms of multiple structural systems.[35] His central innovation in skyscraper design and construction was the concept of the "tube" structural system, including the "framed tube", "trussed tube", and "bundled tube".[36] These systems allow greater economic efficiency,[37] and also allow skyscrapers to take on various shapes, no longer needing to be rectangular and box-shaped.[38] The first building to employ the tube structure was the Chestnut De-Witt apartment building.[33] Over the next fifteen years, many towers were built by Khan and the "Second Chicago School",[39] including the massive 442 m (1,450 ft) Willis Tower.[40] Other pioneers of this field include Hal Iyengar and William LeMessurier.

Chicago, Hong Kong, and New York City, otherwise known as "the big three," are recognized in architectural circles as having especially compelling skylines. A landmark skyscraper can inspire a boom of new high-rise projects in its city, as Taipei 101 has done in Taipei since its opening in 2004.

Modern building practices regarding supertall structures have led to the study of "vanity height".[41][42] Vanity height, according to the CTBUH, is the distance between the highest floor and its architectural top (excluding antennae, flagpole or other functional extensions). Vanity height first appeared in New York City skyscrapers as early as the 1920s and 1930s but supertall buildings have relied on such uninhabitable extensions for on average 30% of their height, raising potential definitional and sustainability issues.[43][44][45] The current era of skyscrapers focuses on sustainability, its built and natural environments, including the performance of structures, types of materials, construction practices, absolute minimal use of materials and natural resources, energy within the structure, and a holistically integrated building systems approach. LEED is a current green building standard.[46]

Architecturally, with the movements of Postmodernism, New Urbanism and New Classical Architecture, that established since the 1980s, a more classical approach came back to global skyscraper design, that remains popular today.[47] Examples are the Wells Fargo Center, NBC Tower, Parkview Square, 30 Park Place, the Messeturm, the iconic Petronas Towers and Jin Mao Tower.

Other contemporary styles and movements in skyscraper design include organic, sustainable, neo-futurist, structuralist, high-tech, deconstructivist, blob, digital, streamline, novelty, critical regionalist, vernacular, Neo Art Deco and neo-historist, also known as revivalist.

Design and construction

The design and construction of skyscrapers involves creating safe, habitable spaces in very tall buildings. The buildings must support their weight, resist wind and earthquakes, and protect occupants from fire. Yet they must also be conveniently accessible, even on the upper floors, and provide utilities and a comfortable climate for the occupants. The problems posed in skyscraper design are considered among the most complex encountered given the balances required between economics, engineering, and construction management.

One common feature of skyscrapers is having a steel framework from which curtain walls are suspended, rather than load-bearing walls of conventional construction. Most skyscrapers have a steel frame that enables to build taller than load-bearing walls of reinforced concrete. Skyscrapers usually have particularly small surface area of what are conventionally thought of as walls, because the walls are not load-bearing and therefore most skyscrapers are characterized by large surface areas of windows made possible by the concept of steel frame and curtain walls. However, skyscrapers can have curtain walls that mimick conventional walls and a small surface area of windows.

The concept of a skyscraper is a product of the industrialized age, made possible by cheap fossil fuel derived energy and industrially refined raw materials such as steel and concrete. The construction of skyscrapers was enabled by steel frame construction that surpassed brick and mortar construction starting at the end of the 19th century and finally surpassing it in the 20th century together with reinforced concrete construction as the price of steel decreased and labour costs increased.

The steel frames become inefficient and uneconomic for supertall buildings as usable floor spaces are reduced for supporting column and due to more usage of steel.[48] Since about 1960, tubular designs have been used for high rises. This reduces the usage of material (more efficient in economic terms - Willis Tower uses a third less steel than the Empire State Building) yet allows greater height. It allows fewer interior columns, and so creates more usable floor space. It further enables buildings to take on various shapes.

Elevators are characteristic to skyscrapers. In 1852 Elisha Otis introduced the safety elevator, allowing convenient and safe passenger movement to upper floors. Another crucial development was the use of a steel frame instead of stone or brick, otherwise the walls on the lower floors on a tall building would be too thick to be practical. Today major manufacturers of elevators include Otis, ThyssenKrupp, Schindler, and KONE.

Basic design considerations

Good structural design is important in most building design, but particularly for skyscrapers since even a small chance of catastrophic failure is unacceptable given the high price. This presents a paradox to civil engineers: the only way to assure a lack of failure is to test for all modes of failure, in both the laboratory and the real world. But the only way to know of all modes of failure is to learn from previous failures. Thus, no engineer can be absolutely sure that a given structure will resist all loadings that could cause failure, but can only have large enough margins of safety such that a failure is acceptably unlikely. When buildings do fail, engineers question whether the failure was due to some lack of foresight or due to some unknowable factor.

Loading and vibration

The load a skyscraper experiences is largely from the force of the building material itself. In most building designs, the weight of the structure is much larger than the weight of the material that it will support beyond its own weight. In technical terms, the dead load, the load of the structure, is larger than the live load, the weight of things in the structure (people, furniture, vehicles, etc.). As such, the amount of structural material required within the lower levels of a skyscraper will be much larger than the material required within higher levels. This is not always visually apparent. The Empire State Building's setbacks are actually a result of the building code at the time, and were not structurally required. On the other hand John Hancock Center's shape is uniquely the result of how it supports loads. Vertical supports can come in several types, among which the most common for skyscrapers can be categorized as steel frames, concrete cores, tube within tube design, and shear walls.

The wind loading on a skyscraper is also considerable. In fact, the lateral wind load imposed on super-tall structures is generally the governing factor in the structural design. Wind pressure increases with height, so for very tall buildings, the loads associated with wind are larger than dead or live loads.

Other vertical and horizontal loading factors come from varied, unpredictable sources, such as earthquakes.

Shear walls

A shear wall, in its simplest definition, is a wall where the entire material of the wall is employed in the resistance of both horizontal and vertical loads. A typical example is a brick or cinderblock wall. Since the wall material is used to hold the weight, as the wall expands in size, it must hold considerably more weight. Due to the features of a shear wall, it is acceptable for small constructions, such as suburban housing or an urban brownstone, to require low material costs and little maintenance. In this way, shear walls, typically in the form of plywood and framing, brick, or cinderblock, are used for these structures. For skyscrapers, though, as the size of the structure increases, so does the size of the supporting wall. Large structures such as castles and cathedrals inherently addressed these issues due to a large wall being advantageous (castles), or ingeniously designed around (cathedrals). Since skyscrapers seek to maximize the floor-space by consolidating structural support, shear walls tend to be used only in conjunction with other support systems.

Steel frame

By 1895, steel had replaced cast iron as skyscrapers' structural material. Its malleability allowed it to be formed into a variety of shapes, and it could be riveted, ensuring strong connections.[49] The simplicity of a steel frame eliminated the inefficient part of a shear wall, the central portion, and consolidated support members in a much stronger fashion by allowing both horizontal and vertical supports throughout. Among steel's drawbacks is that as more material must be supported as height increases, the distance between supporting members must decrease, which in turn increases the amount of material that must be supported. This becomes inefficient and uneconomic for buildings above 40 stories tall as usable floor spaces are reduced for supporting column and due to more usage of steel.[48]

Tube structural systems

The Willis Tower showing the bundled tube frame design

A new structural system of framed tubes was developed in 1963. Fazlur Khan and J. Rankine defined the framed tube structure as "a three dimensional space structure composed of three, four, or possibly more frames, braced frames, or shear walls, joined at or near their edges to form a vertical tube-like structural system capable of resisting lateral forces in any direction by cantilevering from the foundation."[50] Closely spaced interconnected exterior columns form the tube. Horizontal loads (primarily wind) are supported by the structure as a whole. Framed tubes allow fewer interior columns, and so create more usable floor space, and about half the exterior surface is available for windows. Where larger openings like garage doors are required, the tube frame must be interrupted, with transfer girders used to maintain structural integrity. Tube structures cut down costs, at the same time allowing buildings to reach greater heights. Concrete tube-frame construction[36] was first used in the DeWitt-Chestnut Apartment Building, completed in Chicago in 1963,[51] and soon after in the John Hancock Center and World Trade Center.

The tubular systems are fundamental to tall building design. Most buildings over 40-stories constructed since the 1960s now use a tube design derived from Khan’s structural engineering principles,[48][52] examples including the construction of the World Trade Center, Aon Center, Petronas Towers, Jin Mao Building, and most other supertall skyscrapers since the 1960s.[36] The strong influence of tube structure design is also evident in the construction of the current tallest skyscraper, the Burj Khalifa.[38]

Trussed tube and X-bracing

Changes of structure with height. The tubular systems are fundamental for super tall buildings.

Khan pioneered several other variations of the tube structure design. One of these was the concept of X-bracing, or the "trussed tube", first employed for the John Hancock Center. This concept reduced the lateral load on the building by transferring the load into the exterior columns. This allows for a reduced need for interior columns thus creating more floor space. This concept can be seen in the John Hancock Center, designed in 1965 and completed in 1969. One of the most famous buildings of the structural expressionist style, the skyscraper's distinctive X-bracing exterior is actually a hint that the structure's skin is indeed part of its 'tubular system'. This idea is one of the architectural techniques the building used to climb to record heights (the tubular system is essentially the spine that helps the building stand upright during wind and earthquake loads). This X-bracing allows for both higher performance from tall structures and the ability to open up the inside floorplan (and usable floor space) if the architect desires.

The John Hancock Center was far more efficient than earlier steel-frame structures. Where the Empire State Building (1931), required about 206 kilograms of steel per square metre and Chase Manhattan Bank Building (1961) required 275, the John Hancock Center required only 145.[37] The trussed tube concept was applied to many later skyscrapers, including the Onterie Center, Citigroup Center and Bank of China Tower.[53]

Bundled tube

An important variation on the tube frame is the "bundled tube", which uses several interconnected tube frames. The Willis Tower in Chicago used this design, employing nine tubes of varying height to achieve its distinct appearance. The bundled tube structure meant that "buildings no longer need be boxlike in appearance: they could become sculpture."[38]

The elevator conundrum

The invention of the elevator was a precondition for the invention of skyscrapers, given that most people would not (or could not) climb more than a few flights of stairs at a time. The elevators in a skyscraper are not simply a necessary utility, like running water and electricity, but are in fact closely related to the design of the whole structure: a taller building requires more elevators to service the additional floors, but the elevator shafts consume valuable floor space. If the service core, which contains the elevator shafts, becomes too big, it can reduce the profitability of the building. Architects must therefore balance the value gained by adding height against the value lost to the expanding service core.[54] Many tall buildings use elevators in a non-standard configuration to reduce their footprint. Buildings such as the former World Trade Center Towers and Chicago's John Hancock Center use sky lobbies, where express elevators take passengers to upper floors which serve as the base for local elevators. This allows architects and engineers to place elevator shafts on top of each other, saving space. Sky lobbies and express elevators take up a significant amount of space, however, and add to the amount of time spent commuting between floors. Other buildings, such as the Petronas Towers, use double-deck elevators, allowing more people to fit in a single elevator, and reaching two floors at every stop. It is possible to use even more than two levels on an elevator, although this has never been done. The main problem with double-deck elevators is that they cause everyone in the elevator to stop when only people on one level need to get off at a given floor.

Buildings with sky lobbies include the World Trade Center, Petronas Twin Towers and Taipei 101. The 44th-floor sky lobby of the John Hancock Center also featured the first high-rise indoor swimming pool, which remains the highest in America.[55]

Economic rationale

Skyscrapers are usually situated in city centers where the price of land is high. Constructing a skyscraper becomes justified if the price of land is so high that it makes economic sense to build upwards as to minimize the cost of the land per the total floor area of a building. Thus the construction of skyscrapers is dictated by economics and results in skyscrapers in a certain part of a large city unless a building code restricts the height of buildings. Skyscrapers are rarely seen in small cities and they are characteristic of large cities, because of the critical importance of high land prices for the construction of skyscrapers. Usually only office, commercial and hotel users can afford the rents in the city center and thus most tenants of skyscrapers are of these classes. Some skyscrapers have been built in areas where the bedrock is near surface, because this makes constructing the foundation cheaper, for example this is the case in Midtown Manhattan and Lower Manhattan, in New York City, but not in-between these two parts of the city.

Today, skyscrapers are an increasingly common sight where land is expensive, as in the centers of big cities, because they provide such a high ratio of rentable floor space per unit area of land.

\text{Simple price of floor area (currency/}\mathrm{m}^2\text{)} = \frac{\text{price of land area (currency)}} {\text{total floor area (}\mathrm{m}^2\text{)}}

One problem with skyscrapers is car parking. In the largest cities most people commute via public transport, but for smaller cities a lot of parking spaces are needed. Multi-storey car parks are impractical to build very tall, so a lot of land area is needed.

Environmental impact

30 St Mary Axe in London is an example of a modern environmentally friendly skyscraper.

The environmental impact of skyscrapers and whether instead of skyscrapers multiple smaller, lighter buildings would be more environmentally friendly or sustainable is under debate. The concept of a skyscraper is a product of the industrialized age, made possible by cheap fossil fuel derived energy and industrially refined raw materials such as steel and concrete. The construction of skyscrapers was enabled by steel frame construction that surpassed brick and mortar construction starting at the end of the 19th century and finally surpassing it in the 20th century together with reinforced concrete construction as the price of steel decreased and labour costs increased.

The amount of steel, concrete and glass needed to construct a single skyscraper is large, and these materials represent a great deal of embodied energy. Skyscrapers are thus energy intensive buildings, but skyscrapers have a long lifespan, for example the Empire State Building in New York City, United States completed in 1931 and is still in active use. Skyscrapers have considerable mass, which means that they must be built on a sturdier foundation than would be required for shorter, lighter buildings. Building materials must also be lifted to the top of a skyscraper during construction, requiring more energy than would be necessary at lower heights. Furthermore, a skyscraper consumes a lot of electricity because potable and non-potable water have to be pumped to the highest occupied floors, skyscrapers are usually designed to be mechanically ventilated, elevators are generally used instead of stairs, and natural lighting cannot be utilized in rooms far from the windows and the windowless spaces such as elevators, bathrooms and stairwells.

Skyscrapers can be artificially lighted and the energy requirements can be covered by renewable energy or other electricity generation of low greenhouse gas emissions. Heating and cooling of skyscrapers can be efficient, because of centralized HVAC systems, heat radiation blocking windows and small surface area of the building. There is Leadership in Energy and Environmental Design (LEED) certification for skyscrapers. For example the Empire State Building received a gold Leadership in Energy and Environmental Design rating in September 2011 and the Empire State Building is the tallest LEED certified building in the United States, proving that skyscrapers can be environmentally friendly. Also the 30 St Mary Axe in London, the United Kingdom is an environmentally friendly skyscraper.

In the lower levels of a skyscraper a larger percentage of the building cross section must be devoted to the building structure and services than is required for lower buildings:

In low-rise structures, the support rooms (chillers, transformers, boilers, pumps and air handling units) can be put in basements or roof space—areas which have low rental value. There is, however, a limit to how far this plant can be located from the area it serves. The farther away it is the larger the risers for ducts and pipes from this plant to the floors they serve and the more floor area these risers take. In practice this means that in highrise buildings this plant is located on 'plant levels' at intervals up the building.

Further information: Bird-skyscraper collisions

History of the tallest skyscrapers

At the beginning of the 20th century, New York City was a center for the Beaux-Arts architectural movement, attracting the talents of such great architects as Stanford White and Carrere and Hastings. As better construction and engineering technology became available as the century progressed, New York and Chicago became the focal point of the competition for the tallest building in the world. Each city's striking skyline has been composed of numerous and varied skyscrapers, many of which are icons of 20th-century architecture:

Momentum in setting records passed from the United States to other nations with the opening of the Petronas Twin Towers in Kuala Lumpur, Malaysia, in 1998. The record for the world's tallest building has remained in Asia since the opening of Taipei 101 in Taipei, Taiwan, in 2004. A number of architectural records, including those of the world's tallest building and tallest free-standing structure, moved to the Middle East with the opening of the Burj Khalifa in Dubai, United Arab Emirates.

This geographical transition is accompanied by a change in approach to skyscraper design. For much of the twentieth century large buildings took the form of simple geometrical shapes. This reflected the "international style" or modernist philosophy shaped by Bauhaus architects early in the century. The last of these, the Willis Tower and World Trade Center towers in New York, erected in the 1970s, reflect the philosophy. Tastes shifted in the decade which followed, and new skyscrapers began to exhibit postmodernist influences. This approach to design avails itself of historical elements, often adapted and re-interpreted, in creating technologically modern structures. The Petronas Twin Towers recall Asian pagoda architecture and Islamic geometric principles. Taipei 101 likewise reflects the pagoda tradition as it incorporates ancient motifs such as the ruyi symbol. The Burj Khalifa draws inspiration from traditional Islamic art. Architects in recent years have sought to create structures that would not appear equally at home if set in any part of the world, but that reflect the culture thriving in the spot where they stand.

The following list measures height of the roof.[61] The more common gauge is the "highest architectural detail"; such ranking would have included Petronas Towers, built in 1998.

Built Building City Country RoofFloorsPinnacle Current status
1870 Equitable Life Building New York City United States 43 m142 ft 8 Destroyed by fire in 1912
1889 Auditorium Building Chicago United States 82 m269 ft17 106 m349 ft Standing
1890 New York World Building New York City United States 94 m309 ft20 106 m349 ft Demolished in 1955
1894 Manhattan Life Insurance Building New York City United States 106 m348 ft 18 Demolished in 1963
1895 Milwaukee City Hall Milwaukee United States 108 m353 ft 15 Standing
1899 Park Row Building New York City United States 119 m391 ft 30 Standing
1901 Philadelphia City Hall Philadelphia United States 155.8 m511 ft 9 167 m548 ft Standing
1908 Singer Building New York City United States 187 m612 ft 47 Demolished in 1968
1909 Met Life Tower New York City United States 213 m700 ft50 Standing
1913 Woolworth Building New York City United States 241 m792 ft57 Standing
1930 40 Wall Street New York City United States 70283 m927 ft Standing
1930 Chrysler Building New York City United States 282.9 m927 ft77 319 m1,046 ft Standing
1931 Empire State Building New York City United States 381 m1,250 ft102 443 m1,454 ft Standing
1972 World Trade Center (North Tower) New York City United States 417 m1,368 ft110 526.3 m1,727 ft Destroyed in 2001 in the September 11 attacks
1974 Willis Tower (formerly Sears Tower) Chicago United States 442 m1,450 ft 108 527 m1,729 ft Standing
2004 Taipei 101 Taipei Taiwan 449 m 1,474 ft 101 509 m 1,671 ft Standing
2008 Shanghai World Financial Center Shanghai China 487 m 1,599 ft 101 492 m 1,614 ft Standing
2010 Burj Khalifa Dubai United Arab Emirates 828 m 2,717 ft 163 829.8 m 2,722 ft Standing
Taipei 101, formerly the world's tallest skyscraper, was the first to exceed the half-kilometer mark. 
The iconic World Trade Center twin towers were destroyed in 2001. 
The Willis Tower in Chicago was the world's tallest building from 1974 to 1998, and is now the second tallest in the Western Hemisphere. 
The Petronas Twin Towers in Kuala Lumpur. 
Tower 2 of the International Finance Centre in Hong Kong is one of the 20 tallest buildings in the world. 

Future developments

At the time Taipei 101 broke the half-km mark in height, it was already technically possible to build structures towering over a km above the ground. Proposals for such structures have been put forward, including the Kingdom Tower to be built in Jeddah, Saudi Arabia,[62][63] Burj Mubarak Al Kabir in Kuwait and Azerbaijan Tower in Baku. Kilometer-plus structures present architectural challenges that may eventually place them in a new architectural category.[64]

The following skyscrapers, all contenders for being among the tallest in their city or region, are under construction and due to be completed in the next few years:

See also

References

  1. "The Tallest 20 in 2020: Entering the Era of the Megatall". CTBUH. 8 December 2011. Retrieved 19 October 2012.
  2. "skyscraper (building)". Britannica.com. September 11, 2001. Retrieved 2011-11-25.
  3. For more on the origins of the term skyscraper, see "Skyscrapers," Magical Hystory Tour: The Origins of the Commonplace & Curious in America (1 September 2010)
  4. Charles E. Peterson (October 1950). "Ante-Bellum Skyscraper". Journal of the Society of Architectural Historians 9:3: 25–28.
  5. Ivars Peterson (5 April 1986). "The first skyscraper – new theory that Home Insurance Building was not the first". CBS Interactive. Retrieved 2010-01-06. "In my view, we can no longer argue that the Home Insurance Building was the first skyscraper," says Carl W. Condit, now retired from Northwestern University in Evanston, Ill., and author of several books on Chicago architecture. "The claim rests on an unacceptably narrow idea of what constitutes a high-rise commercial building," he says."If there is a building in which all these technical factors—structural system, elevator, utilities—converge at the requisite level of maturity," argues Condit, "it's the Equitable Life Assurance Building in New York." Completed in 1870, the building rose 7½ stories, twice the height of its neighbors.
  6. Data Standards: high-rise building (ESN 18727), Emporis Standards, accessed on line 16 October 2009.
  7. Data Standards: skyscraper (ESN 24419), Emporis Standards, accessed on line 16 October 2009.
  8. "Penza State University of Architecture and Construction; Before The Workshop (1) Tower". Fondazione-delbianco.org. 31 August 1939. Retrieved 2011-06-05.
  9. "Huge New Rogers Skyscraper Proposed". skyscrapernews.com. 3 December 2007. Retrieved 2007-12-03. ...their eleventh proper skyscraper, that is by definition buildings above 150 meters
  10. A.F.K. "The Project Gutenberg eBook of The Cathedral Church of Lincoln, by A.F. Kendric, B.A". Gwydir.demon.co.uk. Retrieved 2011-06-05.
  11. 11.0 11.1 Gregory S. Aldrete: "Daily Life in the Roman City: Rome, Pompeii and Ostia", 2004, ISBN 978-0-313-33174-9, p.79f.
  12. Strabo, 5.3.7
  13. Alexander G. McKay: Römische Häuser, Villen und Paläste, Feldmeilen 1984, ISBN 3-7611-0585-1 p. 231
  14. Papyrus Oxyrhynchus 2719, in: Katja Lembke, Cäcilia Fluck, Günter Vittmann: Ägyptens späte Blüte. Die Römer am Nil, Mainz 2004, ISBN 3-8053-3276-9, p.29
  15. 15.0 15.1 Werner Müller: "dtv-Atlas Baukunst I. Allgemeiner Teil: Baugeschichte von Mesopotamien bis Byzanz", 14th ed., 2005, ISBN 978-3-423-03020-5, p.345
  16. Behrens-Abouseif, Doris (1992). Islamic Architecture in Cairo. Brill Publishers. p. 6. ISBN 90-04-09626-4.
  17. Mortada, Hisham (2003). Traditional Islamic principles of built environment. Routledge. p. viii. ISBN 0-7007-1700-5.
  18. 18.0 18.1 Old Walled City of Shibam, UNESCO
  19. Helfritz, Hans (April 1937). "Land without shade". Journal of the Royal Central Asian Society 24 (2): 201–16. doi:10.1080/03068373708730789.
  20. Shipman, J. G. T. (June 1984). "The Hadhramaut". Asian Affairs 15 (2): 154–62. doi:10.1080/03068378408730145.
  21. "Shrewsbury Flax Mill: Funding for offices and restoration". http://www.bbc.co.uk/news''. BBC News. 30 July 2013. Retrieved 30 July 2013.
  22. "Oriel Chambers". Liverpool Architectural Society. Retrieved 2009-07-14.
  23. Manchester School of Architecture video YouTube
  24. Building Design Architect's website, 8 January 2010
  25. Smith, Chrysti M. (2006). Verbivore's Feast: Second Course: More Word & Phrase Origins. Farcountry Press. p. 289. ISBN 9781560374022. Retrieved 2012-01-19. The word skyscraper, in its architectural context, was first applied to the Home Insurance Building, completed in Chicago in 1885.
  26. Dupré, Judith. Skyscrapers. New York: Black Dog & Leventhal, 1996. Print.
  27. "The Plan Comes Together - Encyclopedia of Chicago". Encyclopedia.chicagohistory.org. Retrieved 2013-07-27.
  28. "Royal Liver Building". Encyclopædia Britannica. Retrieved 2011-06-23.
  29. Hultin, Olof; Bengt O H Johansson; Johan Mårtelius; Rasmus Wærn (1998). The Complete Guide to Architecture in Stockholm. Stockholm: Arkitektur Förlag. p. 62. ISBN 91-86050-43-5.
  30. A Dictionary of Architecture and Landscape Architecture. Oxford University Press. 2006. p. 880. ISBN 0-19-860678-8.
  31. Nordenson, Guy (2008). Seven Structural Engineers: The Felix Candela Lectures. New York City: Museum of Modern Art. p. 21. ISBN 0870707035.
  32. "Mies van der Rohe Dies at 83; Leader of Modern Architecture". The New York Times. August 17, 1969. Retrieved 2007-07-21. Mies van der Rohe, one of the great figures of 20th-century architecture.
  33. 33.0 33.1 Tall Buildings and Urban Habitat - Lynn Beadle - Google Books. Books.google.com. Retrieved 2014-03-12.
  34. "News Article". .lehigh.edu. 2007-03-15. Retrieved 2014-03-12.
  35. Mir M. Ali, Kyoung Sun Moon. "Structural developments in tall buildings: current trends and future prospects". Architectural Science Review (September 2007). Retrieved 2008-12-10.
  36. 36.0 36.1 36.2 Ali, Mir M. (2001). "Evolution of Concrete Skyscrapers: from Ingalls to Jin mao". Electronic Journal of Structural Engineering 1 (1): 2–14. Retrieved 2008-11-30.
  37. 37.0 37.1 Alfred Swenson & Pao-Chi Chang (2008). "Building construction: High-rise construction since 1945". Encyclopædia Britannica. Retrieved 2008-12-09.
  38. 38.0 38.1 38.2 Stephen Bayley (5 January 2010). "Burj Dubai: The new pinnacle of vanity". The Daily Telegraph. Retrieved 2010-02-26.
  39. Billington, David P. (1985). The Tower and the Bridge: The New Art of Structural Engineering. Princeton University Press. pp. 234–5. ISBN 0-691-02393-X.
  40. "List of Tallest skyscrapers in Chicago". Emporis.com. 15 June 2009. Retrieved 2011-06-05.
  41. "Tall Buildings In Numbers Vanity Height". Ctbuh.org. Retrieved 2013-09-21.
  42. "CTBUH releases list of supertall towers with highest percentages of 'vanity height'". World Architecture News. Retrieved 2013-09-21.
  43. "Most of the World's Tallest Buildings Game the System With 'Vanity Height' - Jenny Xie". The Atlantic Cities. 2013-09-09. Retrieved 2013-09-21.
  44. Lecher, Colin. "The World's Tallest Skyscrapers Have A Dirty Little Secret | Popular Science". Popsci.com. Retrieved 2013-09-21.
  45. The Associated Press (2013-09-07). "World's tallest skyscapers? Only if 'useless' needles count". NY Daily News. Retrieved 2013-09-21.
  46. Life-Cycle and Sustainability of Civil Infrastructure Systems: Proceedings ... - Google Books. Books.google.com. Retrieved 2014-03-12.
  47. Adam, Robert. "How to Build Skyscrapers". City Journal. Retrieved 20 September 2014.
  48. 48.0 48.1 48.2 "Lehigh University: Fazlur Rahman Khan Distinguished Lecture Series". Lehigh.edu. Retrieved 2013-06-14.
  49. Leslie, Thomas (June 2010). "Built Like Bridges: Iron, Steel, and Rivets in the Nineteenth-century Skyscraper". Journal of the Society of Architectural Historians 69 (2). University of California Press. pp. 234–261. Abstract only.
  50. "Evolution of Concrete Skyscrapers". Retrieved 2007-05-14.
  51. Alfred Swenson & Pao-Chi Chang (2008). "building construction". Encyclopædia Britannica. Retrieved 2008-12-09.
  52. "Top 10 world's tallest steel buildings". Constructionweekonline.com. Retrieved 2013-06-14.
  53. Dr. D. M Chan. "Introduction to Tall building Structures" (PDF). Teaching.ust.hk. p. 34.
  54. "How Skyscrapers Work: Making it Functional". HowStuffWorks. Retrieved 2008-10-30.
  55. John Hancock Center, Emporis
  56. Edward Robb Ellis (2005). The Epic of New York City: A Narrative History. Carroll & Graf publishers. pp. 405–415. ISBN 0-7867-1436-0. Retrieved 2011-06-05.
  57. "Chrysler Building. Quote: An exhibition in the building's lobby reports the height as 1046". Skyscraperpage.com. Retrieved 2011-06-05.
  58. Emporis GmbH. "– Chrysler Building statistics". Emporis.com. Retrieved 2011-06-05.
  59. "America's Favorite Architecture: Chrysler Building ranked 9th". Favoritearchitecture.org. Retrieved 2011-06-05.
  60. Pollak, Michael (23 April 2006). "75 YEARS: F. Y. I.". The New York Times. Retrieved 2009-10-31.
  61. "The World's Tallest Buildings | Statistics". Emporis. Retrieved 2014-03-12.
  62. "Kingdom Tower". Arabnews.com. 13 October 2008. Retrieved 2011-06-05.
  63. "Zawya". Zawya. Retrieved 2011-06-05.
  64. Owainati, Sadek (3 November 2008). "Reaching for the stars". ArabianBusiness.com. Retrieved 2008-11-15.
  65. Woollard, Deidre (29 November 2008). "Shanghai Tower Breaks Ground – Luxist". Luxist.com. Retrieved 2011-06-05.
  66. "Shanghai Center main building will reach 632 meters". People's Daily Online. 18 August 2008. Retrieved 2008-08-19.
  67. 上海中心大厦项目环境影响报告书简本公示 (PDF) (in Chinese). Envir.gov.cn. 13 August 2008. Retrieved 2008-08-14.
  68. "Shanghai Center". Emporis. Retrieved 2008-05-17.
  69. "Tallest Chinese building features indoor gardens". Shanghai Daily. 24 July 2008. Retrieved 2008-08-09.
  70. "Council on Tall Buildings and Urban Habitat, '100 Future tallest buildings in the world'". Retrieved 2012-08-15.
  71. "Millennium Tower of Frankfurt at". DE /: Emporis.com. Retrieved 2014-03-12.

Further reading

External links

Wikimedia Commons has media related to Skyscrapers.