Q-switching

Q-switching, sometimes known as giant pulse formation or Q-spoiling,[1] is a technique by which a laser can be made to produce a pulsed output beam. The technique allows the production of light pulses with extremely high (gigawatt) peak power, much higher than would be produced by the same laser if it were operating in a continuous wave (constant output) mode. Compared to modelocking, another technique for pulse generation with lasers, Q-switching leads to much lower pulse repetition rates, much higher pulse energies, and much longer pulse durations. The two techniques are sometimes applied together.

Q-switching was first proposed in 1958 by Gordon Gould,[2] and independently discovered and demonstrated in 1961 or 1962 by R.W. Hellwarth and F.J. McClung using electrically switched Kerr cell shutters in a ruby laser.[3]

Principle of Q-switching

Q-switching is achieved by putting some type of variable attenuator inside the laser's optical resonator. When the attenuator is functioning, light which leaves the gain medium does not return, and lasing cannot begin. This attenuation inside the cavity corresponds to a decrease in the Q factor or quality factor of the optical resonator. A high Q factor corresponds to low resonator losses per roundtrip, and vice versa. The variable attenuator is commonly called a "Q-switch", when used for this purpose.

Initially the laser medium is pumped while the Q-switch is set to prevent feedback of light into the gain medium (producing an optical resonator with low Q). This produces a population inversion, but laser operation cannot yet occur since there is no feedback from the resonator. Since the rate of stimulated emission is dependent on the amount of light entering the medium, the amount of energy stored in the gain medium increases as the medium is pumped. Due to losses from spontaneous emission and other processes, after a certain time the stored energy will reach some maximum level; the medium is said to be gain saturated. At this point, the Q-switch device is quickly changed from low to high Q, allowing feedback and the process of optical amplification by stimulated emission to begin. Because of the large amount of energy already stored in the gain medium, the intensity of light in the laser resonator builds up very quickly; this also causes the energy stored in the medium to be depleted almost as quickly. The net result is a short pulse of light output from the laser, known as a giant pulse, which may have a very high peak intensity.

There are two main types of Q-switching:

Active Q-switching

Here, the Q-switch is an externally controlled variable attenuator. This may be a mechanical device such as a shutter, chopper wheel, or spinning mirror/prism placed inside the cavity, or (more commonly) it may be some form of modulator such as an acousto-optic device or an electro-optic device — a Pockels cell or Kerr cell. The reduction of losses (increase of Q) is triggered by an external event, typically an electrical signal. The pulse repetition rate can therefore be externally controlled.

Modulators generally allow a faster transition from low to high Q, and provide better control. An additional advantage of modulators is that the rejected light may be coupled out of the cavity and can be used for something else. Alternatively, when the modulator is in its low-Q state, an externally generated beam can be coupled into the cavity through the modulator. This can be used to "seed" the cavity with a beam that has desired characteristics (such as transverse mode or wavelength). When the Q is raised, lasing builds up from the initial seed, producing a Q-switched pulse that has characteristics inherited from the seed.

Passive Q-switching

In this case, the Q-switch is a saturable absorber, a material whose transmission increases when the intensity of light exceeds some threshold. The material may be an ion-doped crystal like Cr:YAG, which is used for Q-switching of Nd:YAG lasers, a bleachable dye, or a passive semiconductor device. Initially, the loss of the absorber is high, but still low enough to permit some lasing once a large amount of energy is stored in the gain medium. As the laser power increases, it saturates the absorber, i.e., rapidly reduces the resonator loss, so that the power can increase even faster. Ideally, this brings the absorber into a state with low losses to allow efficient extraction of the stored energy by the laser pulse. After the pulse, the absorber recovers to its high-loss state before the gain recovers, so that the next pulse is delayed until the energy in the gain medium is fully replenished. The pulse repetition rate can only indirectly be controlled, e.g. by varying the laser's pump power and the amount of saturable absorber in the cavity. Direct control of the repetition rate can be achieved by using a pulsed pump source as well as passive Q-switching.

Variants

Regenerative amplifier. Red line: Laser beam. Red box: Gain medium. Top: AOM-based design. Bottom: The Pockel’s cell-based design needs thin film polarizers. The direction of the emitted pulse depends on the timing.

Typical performance

A typical Q-switched laser (e.g. a Nd:YAG laser) with a resonator length of e.g. 10 cm can produce light pulses of several tens of nanoseconds duration. Even when the average power is well below 1 W, the peak power can be many kilowatts. Large-scale laser systems can produce Q-switched pulses with energies of many joules and peak powers in the gigawatt region. On the other hand, passively Q-switched microchip lasers (with very short resonators) have generated pulses with durations far below one nanosecond and pulse repetition rates from hundreds of hertz to several megahertz (MHz)

Applications

Q-switched lasers are often used in applications which demand high laser intensities in nanosecond pulses, such as metal cutting or pulsed holography. Nonlinear optics often takes advantage of the high peak powers of these lasers, offering applications such as 3D optical data storage and 3D microfabrication. However, Q-switched lasers can also be used for measurement purposes, such as for distance measurements (range finding) by measuring the time it takes for the pulse to get to some target and the reflected light to get back to the sender. It can be also used in chemical dynamic study, e.g. temperature jump relaxation study.[4]

Q-switched lasers are also used to remove tattoos. They are used to shatter tattoo pigment into particles that are cleared by the body's lymphatic system. Full removal can take between six and twenty treatments depending on the amount and colour of ink, spaced at least a month apart, using different wavelengths for different coloured inks. Nd:YAG lasers are currently the most favoured lasers due to their high peak powers, high repetition rates and relatively low costs. In 2013 a picosecond laser was introduced based on clinical research which appears to show better clearance with 'difficult' colours such as green and light blue.

See also

References

  1. ↑ Früngel, Frank B. A. (2014). Optical Pulses - Lasers - Measuring Techniques. Academic Press. p. 192. ISBN 9781483274317. Retrieved 1 February 2015.
  2. ↑ Taylor, Nick (2000). LASER: The inventor, the Nobel laureate, and the thirty-year patent war. New York: Simon & Schuster. ISBN 0-684-83515-0. p. 93.
  3. ↑ McClung, F.J.; Hellwarth, R.W. (1962). "Giant optical pulsations from ruby". Journal of Applied Physics 33 (3): 828–829. doi:10.1063/1.1777174.
  4. ↑ Reiner, J. E.; Robertson, J. W. F.; Burden, D. L.; Burden, L. K.; Balijepalli, A.; Kasianowicz, J. J. (2013). "Temperature Sculpting in Yoctoliter Volumes". Journal of the American Chemical Society. doi:10.1021/ja309892e. ISSN 0002-7863.