Phantom power

This article is about the use in microphones. For power consumed by appliances while they are off, see standby power. For other uses, see Phantom Power (disambiguation).
"Phantom voltage" redirects here. For unintentional voltages in power distribution systems, see stray voltage.

Phantom power, in the context of professional audio equipment, is a method for transmitting DC electric power through microphone cables to operate microphones that contain active electronic circuitry.[1] It is best known as a convenient power source for condenser microphones, though many active direct boxes also use it. The technique is also used in other applications where power supply and signal communication take place over the same wires.

Phantom power supplies are often built into mixing desks, microphone preamplifiers and similar equipment. In addition to powering the circuitry of a microphone, traditional condenser microphones also use phantom power for polarizing the microphone's transducer element. Three variants of phantom power, called P12, P24 and P48, are defined in the international standard IEC 61938.[2]

A condenser microphone requires power to produce a DC polarizing voltage and to power an internal amplifier required to drive long cables

Technical information

Phantom powering consists of a phantom circuit where direct current is applied equally through the two signal lines of a balanced audio connector (in modern equipment, usually an XLR connector). The supply voltage is referenced to the ground pin of the connector (pin 1 of an XLR), which normally is connected to the cable shield or a ground wire in the cable or both. When phantom powering was introduced, one of its advantages was that the same type of balanced, shielded microphone cable that studios were already using for dynamic microphones could be used for condenser microphones. This is in contrast to microphones with vacuum-tube circuitry, most of which require special, multi-conductor cables.[note 1]

One method of supplying phantom power. A microphone or other device can obtain DC power from either signal line to ground terminal, and two capacitors block this DC from appearing at the output. R1 and R2 should be 6.8k ohms for 48 volt phantom, and R3 should not be used.

With phantom power, the supply voltage is effectively invisible to balanced microphones that do not use it, which includes most dynamic microphones. A balanced signal consists only of the differences in voltage between two signal lines; phantom powering places the same DC voltage on both signal lines of a balanced connection. This is in marked contrast to another, slightly earlier method of powering known as "parallel powering" or "T-powering" (from the German term Tonaderspeisung), in which DC was overlaid directly onto the signal in differential mode. Connecting a conventional microphone to an input that had parallel powering enabled could very well damage the microphone.

Many mixer boards have a switch for turning phantom power on or off; in most high-end equipment this can be done individually by channel, or on smaller mixers all mic channels can be either on or off, also this can be done in groups in most mid-range boards and some smaller ones. If it is desired to disconnect phantom power from one channel only, this can be done by using a 1:1 isolation transformer or blocking capacitors. Phantom powering can cause equipment malfunction or even damage if used with cables or adapters that connect one side of the input to ground, or if certain equipment other than microphones is connected to it.

Instrument amplifiers rarely provide phantom power. To use equipment requiring it with these amplifiers, a separate power supply must be inserted into the line. These are readily available commercially, or alternatively are one of the easier projects for the amateur electronics constructor.

History

Phantom powering was used in telephone systems since the introduction of the rotary-dial telephone in 1919 before it was applied to condenser microphones. One such application in the telephone system was to provide a DC signaling path around transformer connected amplifiers in analogue line transmission systems. The first known commercially available phantom-powered microphone was the Schoeps model CMT 20, which came out in 1964, built to the specifications of French radio with 9–12 volt DC phantom power; the positive pole of this powering was grounded. Microphone preamplifiers of the Nagra IV-series tape recorders offered this type of powering as an option for many years and Schoeps continued to support "negative phantom" until the CMT series was discontinued in the mid-1970s, but it is obsolete now.

In 1966, Neumann GmbH of Berlin, Germany, presented a new type of transistorized microphone to the Norwegian Broadcasting Corporation, NRK. Norwegian Radio had requested phantom-powered operation. Since NRK already had 48 V available in their studios for their emergency lighting systems, this voltage was used for powering the new microphones (model KM 84), and is the origin of 48-V phantom power. This arrangement was later standardized in DIN 45596.

The prevailing international standard, IEC 61938, defines 48-volt, 24-volt, and 12-volt phantom powering. The signal conductors are positive, both fed through resistors of equal value (for 48-volt phantom powering, the standard value is 6.8 kΩ), and the shield is ground. The 6.8 kΩ value is not critical, but the resistors must be matched to within 0.4% or better to maintain good common-mode rejection in the circuit. The 24-volt version of phantom powering, proposed quite a few years after the 12 and 48 V versions, was also included in the DIN standard and is in the IEC standard, but it was never widely adopted by equipment manufacturers.

An external phantom power supply.

Caveats

Some microphones offer a choice of internal battery powering or (external) phantom powering. In some such microphones it is advisable to remove the internal batteries when phantom power is being used since batteries may corrode and leak chemicals. Other microphones are specifically designed to switch over to the internal batteries if an external supply fails, which may be useful.

Phantom powering is not always implemented correctly or adequately, even in professional-quality preamps, mixers, and recorders. In part this is because first-generation (late-1960s through mid-1970s) 48-volt phantom-powered condenser microphones had simple circuitry and required only small amounts of operating current (typically less than 1 mA per microphone), so the phantom supply circuits typically built into recorders, mixers, and preamps of that time were designed on the assumption that this current would be adequate. The original DIN 45596 phantom-power specification called for a maximum of 2 mA. This practice has carried forward to the present; many 48-volt phantom power supply circuits, especially in low-cost and portable equipment, simply cannot supply more than 1 or 2 mA total without breaking down. Some circuits also have significant additional resistance in series with the standard pair of supply resistors for each microphone input; this may not affect low-current microphones much, but it can disable microphones that need more current.

Mid-1970s and later condenser microphones designed for 48-volt phantom powering often require much more current (e.g., 2–4 mA for Neumann transformerless microphones, 4–5 mA for the Schoeps CMC ("Colette") series and Josephson microphones, 5–6 mA for most Shure KSM-series microphones, 8 mA for CAD Equiteks and 10 mA for Earthworks). The IEC standard gives 10 mA as the maximum allowed current per microphone. If its required current is not available, a microphone may still put out a signal, but it cannot deliver its intended level of performance. The specific symptoms vary somewhat, but the most common result will be reduction of the maximum sound-pressure level that the microphone can handle without overload (distortion). Some microphones will also show lower sensitivity (output level for a given sound-pressure level).

Most ground lift switches have the unwanted effect of disconnecting phantom power. There must always be a DC current path between pin 1 of the microphone and the negative side of the 48 volt supply, if power is to reach the microphone's electronics. Lifting the ground, which is normally pin 1, breaks this path and disables the phantom power supply.

If there is a fault in the cable, phantom power may damage some vintage mics.[3] Equipment damage is also possible if a phantom-powered input is configured for connection to an unbalanced dynamic microphone[4] or electronic musical instruments.[5] The transient generated when a microphone is hot-plugged into an input with active phantom power can damage downstream equipment and possibly the preamp circuit of the input.[6] It is considered good practice to disable phantom power to devices that don't require it.[7][8]

Digital phantom power

Digital microphones complying with the AES 42 standard may be provided with phantom power at 10 volts, impressed on both audio leads and ground. This supply can furnish up to 250 mA to digital microphones. A keyed variation of the usual XLR connector, the XLD connector, may be used to prevent accidental interchange of analog and digital devices.[9]

Other microphone powering techniques

T-power, also known as A-B powering[10] or 12T, described in DIN 45595, is an alternative to phantom powering that is still widely used in the world of production film sound. Most mixers and recorders intended for that market have a T-power option. Many older Sennheiser and Schoeps microphones use this powering method, although newer recorders and mixers are phasing out this option. Adapter barrels, and dedicated power supplies, are made to accommodate T powered microphones. There is no audible difference between microphones featuring this method and microphones with P48 powering. In this scheme, 12 volts is applied through 180 ohm resistors between the microphone's "hot" terminal (XLR pin 2) and the microphone's "cold" terminal (XLR pin 3). This results in a 12 volt potential difference with significant current capability across pins 2 and 3, which would likely cause permanent damage if applied to a dynamic or ribbon microphone.

Line powering, or plug-in-power (PiP), is the low-current 3 V to 5 V supply provided at the microphone jack of some consumer equipment, such as portable recorders and computer sound cards. It is unlike phantom power since there is no shield connection on these jacks. Instead, a low voltage (around +5 volts) is connected to the tip and ring of the 3.5 mm jack through resistors around 2.2 kilohms, with return through the sleeve; the DC power is in common with the audio signal from the microphone. Capacitors are used to block the DC from subsequent audio frequency circuits. It is often used for powering electret microphones, which will not function without power. It is suitable only for powering microphones specifically designed for use with this type of power supply. Damage may result if these microphones are connected to true (48 V) phantom power through a 3.5 mm to XLR adapter that connects the XLR shield to the 3.5 mm sleeve. [11] Plug-in-power is covered by Japanese standard CP-1203A:2007[12] A similar line-powering scheme is found in computer sound cards. Both plug-in-power and soundcard power are defined in a not-yet-released version of IEC 61938.

Some condenser microphones can be powered with a 1.5 volt cell contained in a small compartment in the microphone or in an external housing.

These alternative powering schemes are sometimes improperly referred to as "phantom power" and should not be confused with true 48-volt phantom powering described above.

Phantom power is also used by workers in avionics to describe the DC bias voltage used to power aviation microphones, which use a lower voltage than professional audio microphones. Phantom power used in this context is 8 to 16 volts DC in series with a 470 ohm (nominal) resistor as specified in RTCA Inc. standard DO-214.[13] These microphones evolved from the carbon microphones used in the early days of aviation and the telephone which relied on a DC bias voltage across the carbon microphone element.

Other uses

Phantom power is also used in applications other than microphones:

Notes

  1. ↑ There are phantom-powered vacuum tube microphones, such as the Microtech Gefell UM900 and Audio-Technica AT3060

See also

References

  1. ↑ David Miles Huber, Robert E. Runstein Modern Recording Techniques, Focal Press 2009 ISBN 0-240-81069-4, page 117
  2. ↑ http://webstore.iec.ch/webstore/webstore.nsf/Artnum_PK/21724
  3. ↑ "Can phantom power damage your microphones?". 2012-05-24. Retrieved 2013-06-05. Sending Phantom Power to an old (prior to 1970 design) ribbon microphone without an isolating transformer, while using a bad cable, which has the ground (pin 1) shorted to pin 2 or pin 3 of the XLR. This is the one classic example why everybody says - do not send phantom power to ribbon microphones, but the chances of this “perfect storm” to happen are really not that big.
  4. ↑ Gary Davis (1989). The Sound Reinforcement Handbook. Hal Leonard Corporation. p. 130. ISBN 9781617745454.
  5. ↑ "Q. Has phantom power damaged this keyboard?". Sound on Sound. January 2013. Retrieved 2013-06-05.
  6. ↑ Bortoni, Rosalfonso; Kirkwood, Wayne (March 2010). "The 48-Volt Phantom Menace Returns". Audio Engineering Society.
  7. ↑ "Ribbon Mics and Phantom Power". Royer. Retrieved 2013-06-05.
  8. ↑ Tomlinson Holman (2012-11-12). Sound for Film and Television. CRC Press. p. 304. ISBN 9781136046094.
  9. ↑ Francis Rumsey; John Watkinson (2004). Digital interface handbook third edition. Elsevier. p. 204. ISBN 0-240-51909-4.
  10. ↑ Michael Talbot-Smith Sound assistance, Focal Press, 1999 ISBN 0-240-51572-2, pages 94,95
  11. ↑ http://www.microphone-data.com/media/filestore/articles/Powering%20mics-10.pdf Chris Woolf Powering Microphones, retrieved 2013 April 28
  12. ↑ http://www.jeita.or.jp/cgi-bin/standard_e/list.cgi?cateid=1&subcateid=6
  13. ↑ http://www.rtca.org/ RTCA DO-214

External links