National pipe thread

Threaded pipe and elbow. The pipe has a male NPT thread, while the elbow's is female.

National Pipe Thread Taper (NPT) is a U.S. standard for tapered threads used on threaded pipes and fittings. In contrast to straight threads that are found on a bolt, a taper thread will pull tight and therefore make a fluid-tight seal. In America, William Sellers set the standard for nuts, bolts, and screws which became the National Pipe Tapered Thread (NPT) in 1864.^[1]

Usage

Threaded pipes can provide an effective seal for pipes transporting liquids, gases, steam, and hydraulic fluid. These threads are now used in materials other than steel and brass, including PTFE,^[2] PVC, nylon, bronze, and cast iron.

The taper on NPT threads allows them to form a seal when torqued as the flanks of the threads compress against each other, as opposed to parallel/straight thread fittings or compression fittings in which the threads merely hold the pieces together and do not provide the seal. As the thread body is tapered (0.75 in/ft or 62.5 mm/m) a larger diameter keeps compressing into a smaller diameter and finally forms a seal (no clearance remains between the crests and roots of the threads because of the taper). This means that NPT fittings should be burr-free and lubricated using a lubricating material like lubricating paste or tape. The use of tape also helps to limit corrosion on the threads, which otherwise can make future disassembly nearly impossible.

Commonly used sizes are ¹⁄₈, ¹⁄₄, ³⁄₈, ¹⁄₂, ³⁄₄, 1, 1 ¹⁄₄, 1 ¹⁄₂, and 2 inch, appearing on pipes and fittings by most U.S. suppliers. Sizes smaller than ¹⁄₈ inch are occasionally used for compressed air, while sizes larger than 2 inches are uncommon, due to the use of alternative methods of joining that are used with these larger sizes.

Specifications

NPT is defined by ANSI/ASME standard B1.20.1.^[3]

Pipe threads are different from machine-screw and bolt threads. Those are designated NC (national coarse) and NF (national fine.) The biggest difference is the taper on pipe threads.

The taper rate for all NPT threads is 1 in 16 (³⁄₄ inch per foot or 62.5 millimeters per meter) measured by the change of diameter (of the pipe thread) over distance. The angle between the taper and the center axis of the pipe is tan⁻¹(¹⁄₃₂) = 1.7899° = 1° 47′ 24″.

Nominal Pipe Size (NPS) is loosely related to the inside diameter of Schedule 40 pipe. Because of the pipe wall thickness, the actual diameter of the threads is larger than the NPS, considerably so for small NPS. Pipe of other schedules with a certain NPS has different wall thickness, but the same outside diameter and thread profile as Schedule 40, so the inside diameter of the pipe is therefore different from the NPS.

Thread form

NPTE and NPS threads have a 60° included angle and have a Sellers thread form (flattened peaks and valleys).

NPTF

A semi-compatible variant called National Pipe Taper Fuel (NPTF), also called Dryseal American National Standard Taper Pipe Thread, defined by ASME B1.20.3, is designed to provide a more leak-free seal without the use of teflon tape or other sealant compound. NPTF threads are the same basic shape but with crest and root heights adjusted for an interference fit, eliminating the spiral leakage path.

Informal Subsets

MPT

MPT can mean Male Pipe Thread or Mechanical Pipe Thread (a non-tapered variety) and is a subset of NPT for male connections.

FPT

FPT means Female Pipe Thread and is a subset of NPT for female connections.

Table of standard sizes

See also

References

Further reading

• Oberg, Erik; Franklin D. Jones; Holbrook L. Horton; Henry H. Ryffel (2000). ed. Christopher J. McCauley, Riccardo Heald, and Muhammed Iqbal Hussain, ed. Machinery's Handbook (26th edition ed.). New York: Industrial Press Inc. ISBN 0-8311-2635-3. 

External links

• ASME B1.20.-1983 Pipe Threads, General Purpose, Inch
• pipeandhose.com