Line code

An example of coding a binary signal using rectangular pulse amplitude modulation with polar non-return-to-zero code An example of Bipolar encoding, or AMI. Encoding of 11011000100 in Manchester encoding An example of Differential Manchester encoding An example of Biphase mark code An example of MLT-3 encoding.

In telecommunication, a line code (also called digital baseband modulation or digital baseband transmission method) is a code chosen for use within a communications system for baseband transmission purposes. Line coding is often used for digital data transport.

Line coding

Line coding consists of representing the digital signal to be transported by an amplitude- and time-discrete signal that is optimally tuned for the specific properties of the physical channel (and of the receiving equipment). The waveform pattern of voltage or current used to represent the 1s and 0s of a digital data on a transmission link is called line encoding. The common types of line encoding are unipolar, polar, bipolar, and Manchester encoding.

For reliable clock recovery at the receiver, one usually imposes a maximum run length constraint on the generated channel sequence, i.e., the maximum number of consecutive ones or zeros is bounded to a reasonable number. A clock period is recovered by observing transitions in the received sequence, so that a maximum run length guarantees such clock recovery, while sequences without such a constraint could seriously hamper the detection quality.

After line coding, the signal is put through a "physical channel", either a "transmission medium" or "data storage medium".^[1][2] Sometimes the characteristics of two very different-seeming channels are similar enough that the same line code is used for them. The most common physical channels are:

• the line-coded signal can directly be put on a transmission line, in the form of variations of the voltage or current (often using differential signaling).
• the line-coded signal (the "baseband signal") undergoes further pulse shaping (to reduce its frequency bandwidth) and then modulated (to shift its frequency) to create an "RF signal" that can be sent through free space.
• the line-coded signal can be used to turn on and off a light source in free-space optical communication, most commonly used in an infrared remote control.
• the line-coded signal can be printed on paper to create a bar code.
• the line-coded signal can be converted to magnetized spots on a hard drive or tape drive.
• the line-coded signal can be converted to pits on an optical disc.

Unfortunately, most long-distance communication channels cannot transport a DC component. The DC component is also called the disparity, the bias, or the DC coefficient. The simplest possible line code, called unipolar because it has an unbounded DC component, gives too many errors on such systems.

Most line codes eliminate the DC component – such codes are called DC-balanced, zero-DC, DC-free, zero-bias, DC equalized, etc. There are three ways of eliminating the DC component:

• Use a constant-weight code. In other words, each transmitted code word is corrected such that every code word that contains some positive or negative levels also contains enough of the opposite levels, such that the average level over each code word is zero. For example, Manchester code and Interleaved 2 of 5.
• Use a paired disparity code. In other words, the transmitter has to make sure that every code word that averages to a negative level is paired with another code word that averages to a positive level. Therefore it must keep track of the running DC buildup, and always pick the code word that pushes the DC level back towards zero. The receiver is designed so that either code word of the pair decodes to the same data bits. For example, AMI, 8B10B, 4B3T, etc.
• Use a scrambler. For example, the scrambler specified in RFC 2615 for 64b/66b encoding.

Unfortunately, several long-distance communication channels have polarity ambiguity. There are three ways of providing unambiguous reception of "0" bits or "1" bits over such channels:

• differential coding
• MLT-3 encoding
• invert the whole stream when inverted syncwords are detected

Line coding should make it possible for the receiver to synchronize itself to the phase of the received signal. If the synchronization is not ideal, then the signal to be decoded will not have optimal differences (in amplitude) between the various digits or symbols used in the line code. This will increase the error probability in the received data.

It is also preferred for the line code to have a structure that will enable error detection. Note that the line-coded signal and a signal produced at a terminal may differ, thus requiring translation.

A line code will typically reflect technical requirements of the transmission medium, such as optical fiber or shielded twisted pair. These requirements are unique for each medium, because each one has different behavior related to interference, distortion, capacitance and loss of amplitude.

Common line codes

Optical line codes:

• Carrier-Suppressed Return-to-Zero
• Alternate-Phase Return-to-Zero
• Three of Six, Fiber Optical (TS-FO)

See also

• Channel coding
• Source coding
• Modulation
• Physical layer
• Self-synchronizing code and bit synchronization

References

•  This article incorporates public domain material from the General Services Administration document "Federal Standard 1037C" (in support of MIL-STD-188).

External links

• Line Codes Analyzer: tool for graphical comparison of line codes
• Line Coding Lecture No. 9
• Line Coding in Digital Communication

Line coding (digital baseband transmission) Main articles Unipolar encoding Bipolar encoding On-off keying Basic line codes Return to zero (RZ) Non-return-to-zero, level (NRZ/NRZ-L) Non-return-to-zero, inverted (NRZ-I) Non-return-to-zero, space (NRZ-S) Manchester Differential Manchester/biphase (Bi-φ) Extended line codes Conditioned Diphase 4B3T 4B5B 2B1Q Alternate mark inversion Modified AMI code Coded mark inversion MLT-3 encoding Hybrid ternary code 6b/8b encoding 8b/10b encoding 64b/66b encoding Eight-to-fourteen modulation Delay/Miller encoding TC-PAM Optical line codes Carrier-suppressed return-to-zero Alternate-phase return-to-zero See also: Baseband Baud Bit rate Digital signal Digital transmission Ethernet physical layer Pulse modulation methods Pulse-amplitude modulation (PAM) Pulse code modulation (PCM) Serial communication Category:Line codes