ISO 898

ISO 898 is an international standard that defines mechanical and physical properties for metric fasteners. This standard is the origin for other standards that define properties for similar metric fasteners, such as SAE J1199 and ASTM F568M.^[1] It is divided into five (nonconsecutive) parts:

1. Bolts, screws and studs with specified property classes – Coarse thread and fine pitch thread^[2]

2. Nuts with specified proof load values – Coarse thread^[3]

5. Set screws and similar threaded fasteners not under tensile stresses^[4]

6. Nuts with specified proof load values – Fine pitch thread^[5]

7. Torsional test and minimum torques for bolts and screws with nominal diameters 1 mm to 10 mm^[6]

With exception to part 7, which defines test standards, the parts of this standard define properties for fasteners made of carbon steel and alloy steel. The standards define that the testing must be performed at ambient temperatures, which is defined as between 10 and 35 °C (50 and 95 °F). The standards do not cover fasteners that would otherwise apply but require special properties, such as weldability or corrosion resistance.^[2][3][4]

Part 1

Part 1 defines the mechanical properties of bolts, screws, and studs. It specifically applies to fasteners that have an ISO metric screw thread as defined in ISO 68-1. The properties are defined for M1.6-39 with coarse threads and M8-39 with fine threads. The diameter and pitch combinations must adhere to ISO 261 and ISO 262 and the thread tolerances must adhere to ISO 965 parts 1, 2, and 4.^[2]

Part 1 does not specify properties for fasteners that have head geometries that reduce the shear strength of the fastener, such as low head screws and countersunk heads. It also excludes set screws, which are covered under part 5.^[2]

Part 2

Part 2 defines the mechanical properties for coarse threaded nuts up to an M39 size and a height of at least half the nominal diameter.^[3]

Part 5

Part 5 defines the mechanical properties for set screws and other fasteners not under tensile stresses. It defines properties for sizes M1.6 through M24.^[4]

Part 6

Part 6 is the same as part 2 except for fine threaded nuts that range from M8 to M39. Note that the working temperature range for these fasteners is −50 to 300 °C (−58 to 572 °F)^[5]

Part 7

Part 7 defines how to perform torsional tests on bolts and screws that have a nominal diameter less than or equal to 10 mm. This standard only applies to short screws and bolts with a nominal diameter between 3 and 10 mm.^[6]

References

Bibliography

• Bickford, John H.; Nassar, Sayed (1998), Handbook of bolts and bolted joints, CRC Press, ISBN 978-0-8247-9977-9 .

Further reading

• Blake, Alexander (1986), What every engineer should know about threaded fasteners: materials and design, CRC Press, ISBN 978-0-8247-7554-4 .
• Hagiwara, Masaya; Sakai, Hiroaki (2007), "Verification of the Design Concept on Nuts in Bolt/Nut Assembly for Revision of ISO 898-2 and ISO 898-6", Journal of Advanced Mechanical Design, Systems, and Manufacturing 1 (5): 755–762, doi:10.1299/jamdsm.1.755 .
• Timings, Roger Leslie (2005), Newnes mechanical engineer's pocket book (3rd ed.), Newnes, pp. 196–234, ISBN 978-0-7506-6508-7 .

External links

• Mechanical properties of common ISO property classes

ISO standards by standard number List of ISO standards / ISO romanizations / IEC standards 1–9999 1 2 3 4 5 6 7 9 16 31 -0 -1 -2 -3 -4 -5 -6 -7 -8 -9 -10 -11 -12 -13 128 216 217 226 228 233 259 269 302 306 428 518 519 639 -1 -2 -3 -5 -6 646 690 732 764 843 898 965 1000 1004 1007 1073-1 1413 1538 1745 1989 2014 2015 2022 2047 2108 2145 2146 2240 2281 2709 2711 2788 2852 3029 3103 3166 -1 -2 -3 3297 3307 3602 3864 3901 3977 4031 4157 4217 4909 5218 5428 5775 5776 5800 5964 6166 6344 6346 6385 6425 6429 6438 6523 6709 7001 7002 7098 7185 7200 7498 7736 7810 7811 7812 7813 7816 8000 8178 8217 8571 8583 8601 8632 8652 8691 8807 8820-5 8859 -1 -2 -3 -4 -5 -6 -7 -8 -8-I -9 -10 -11 -12 -13 -14 -15 -16 8879 9000/9001 9075 9126 9293 9241 9362 9407 9506 9529 9564 9594 9660 9897 9945 9984 9985 9995 10000–19999 10006 10116 10118-3 10160 10161 10165 10179 10206 10218 10303 -11 -21 -22 -28 -238 10383 10487 10585 10589 10646 10664 10746 10861 10957 10962 10967 11073 11170 11179 11404 11544 11783 11784 11785 11801 11898 11940 (-2) 11941 11941 (TR) 11992 12006 12182 12207 12234-2 13211 -1 -2 13216 13250 13399 13406-2 13407 13450 13485 13490 13567 13568 13584 13616 14000 14031 14224 14289 14396 14443 14496 -2 -3 -6 -10 -11 -12 -14 -17 -20 14644 -1 -2 -3 -4 -5 -6 -7 -8 -9 14649 14651 14698 -2 14750 14764 14882 14971 15022 15189 15288 15291 15292 15398 15408 15444 -3 15445 15438 15504 15511 15686 15693 15706 -2 15707 15897 15919 15924 15926 15926 WIP 15930 16023 16262 16612-2 16750 16949 (TS) 17024 17025 17203 17369 17799 18000 18004 18014 18245 18629 18916 19005 19011 19092 (-1 -2) 19114 19115 19125 19136 19439 19500 19501 19502 19503 19505 19506 19507 19508 19509 19510 19752 19757 19770 19775-1 19794-5 19831 20000+ 20000 20022 20121 21000 21047 21500 21827:2002 22000 23270 23271 23360 24517 24613 24617 24707 25178 25964 26000 26300 26324 27000 series 27000 27001:2005 27001:2013 27002 27003 27004 27005 27006 27007 27729 27799 28000 29110 29148 29199-2 29500 30170 31000 32000 38500 42010 80000 -1 -2 -3 -4 -5 -6 -7 -8 -9 -10 -11 -12 -13 -14 Categories ISO standards ISO 639 ISO 3166 ISO / IEC standards OSI protocols All articles with prefix "ISO"