Hot pressing

Hot pressing is a high-pressure, low-strain-rate powder metallurgy process for forming of a powder or powder compact at a temperature high enough to induce sintering and creep processes.^[1] This is achieved by the simultaneous application of heat and pressure.

Hot pressing is mainly used to fabricate hard and brittle materials. One large use is in the consolidation of diamond-metal composite cutting tools and technical ceramics. The densification works through particle rearrangement and plastic flow at the particle contacts. The loose powder or the pre-compacted part is in most of the cases filled to a graphite mould that allows induction or resistance heating up to temperatures of typically 2,400 °C (4,350 °F). Pressures of up to 50 MPa (7,300 psi) can be applied.other great use is in the pressing of different types of polymers.

Within hot pressing technology, three distinctly different types of heating can be found in use: induction heating, indirect resistance heating, and FAST / Direct Hot Pressing.

Inductive heating

Figure I: Conventional inductive heating

In this process heat is produced within the mould when it is subjected to a high frequency electromagnetic field, generated by using an induction coil coupled to an electronic generator. The mold is made out of graphite or steel, and pressure is applied by one or two cylinders onto the punches. The mold is positioned within the induction coil. The advantage here is that the pressure and the inductive power are completely independent. Even powders with a liquid phase are amenable to this process and low pressures are possible, too. Among the disadvantages are the expense of a high-frequency generator and the need for proper alignment. If the mold is placed off centre, the heat distribution is uneven. But the main disadvantage is the dependence of the process on good inductive coupling and thermal conductivity of the mold. The magnetic field can penetrate the mold only 0.5mm to 3mm. From there on, the heat has to be "transported" into the mold by the thermal conductivity of the mould material. Uniform heating is much more difficult if the air gap between the mold and the inductive coil is not the same all along the mould profile. Another potential problem is heating rate. Too high a heat up rate will result in high temperature differences between the surface and core that can destroy the mold.

Indirect resistance heating

Figure II: Indirect resistance heating

With indirect resistance heating technology, the mold is placed in a heating chamber. The chamber is heated by graphite heating elements. These elements are heated by electrical current. The heat is then transferred into the mold by convection. As the electrical energy heats the heating elements that then heat the mold in a secondary manner, the process is called indirect resistance heating.

Advantages are high achievable temperatures, independent from the conductivity of the mold and independent from heat and pressure. Main disadvantage is the time that it takes to heat up the mold. It takes relatively long for heat transfer to take place from the furnace atmosphere to the mold surface and subsequently throughout the cross-section of the mold.

Field Assisted Sintering Technique (FAST) / Direct Hot Pressing

Figure III: Direct hot pressing

The basic idea of sintering with electric current going through the mold is quite old. Resistance heating of cemented carbide powders was patented by Tayler^[2] as early as 1933. This method is currently undergoing renewed interest. When applying a standard (unpulsed) AC or DC current, it is often referred to as "FAST Direct Hot Pressing (FAST DHP)", which is a common term in many industries. Another common term is "Rapid Hot Pressing (RHP)". When applying a pulsed DC current, it is referred to as "Spark Plasma Sintering (SPS)". Both techniques are summarized under the generic term "Field Assisted Sintering Technique (FAST)".

The compelling reason for shortening the cycle time then was to avoid grain growth and also save energy. In direct hot pressing, the mold is directly connected to electrical power. The resistivity of the mold and the powder part generates the heat directly in the mold. This results in very high heating rates. Additionally, this leads to significant increase in the sintering activity of fine metal powder aggregates which makes short cycle times of a few minutes possible. Further, this process lowers the threshold sintering temperature and pressure compared to that required in conventional sintering processes. The previous two methods are both closely dependent on the an intrinsic property of the mold material, i.e., its thermal conductivity. With direct resistance heating, however, the heat is generated where it is needed.

Latest research suggests that there is no evident difference between sintering with pulsed or unpulsed current (SPS or FAST DHP). The same improved sinter results (compared to conventional sintering) can be achieved by all direct hot pressing techniques.^[3]

Applications

Recently, the manufacture of such critical items as sputtering targets and high-performance ceramic components, such as boron carbide, titanium diboride, and sialon, have been achieved. Using metal powder, the conductivity of the mold is ideal for fast heating of the work-piece. Molds that have a big diameter and relatively small height can be heated up very fast. The process is especially suitable for applications that need high heating rates, e.g. for materials that should not be kept at high temperatures too long or for processes that require fast heating rates for high productivity.

With the direct hot pressing technology, materials can be sintered to their final density. The near net-shape precision achieved is very high and saves in many cases mechanical reworking of the high grade materials that are often difficult to process.

In the friction material industry, direct hot pressing plays an increasing role for the production of sintered brake pads and clutches. Sintered brake pads are increasingly used for example for high speed train and motorcycle applications, as well as wind energy, ATVs, mountain bikes and for many industrial applications. Sintered clutch discs are predominantly used for heavy-duty trucks, vessels, tractors and other agricultural machines.

Research facilities such as universities and institutes take advantage of the short sinter cycles which help to speed up the research process.

Latest development work include metal-diamond-composite heat sinks, for example for LED and laser applications. Sintering metal-diamond compounds with direct hot presses, however, goes back to the 1950s since when it is commonly practised in the diamond tool industry.

Figure IV: Process layout of the co-sintering process; total cycle time 11.5 mins Key: Red/orange line: actual/set temperature Green line: densification of powder/green compact Dark blue/light blue: actual/set pressure

Notes