HP Integrity Servers

HP Integrity Superdome, or the "black" one

HP Integrity are a series of server computers produced by Hewlett-Packard since 2003, based on the Itanium processor architecture. The Integrity brand name was inherited by HP from Tandem Computers via Compaq.

General

HP supports the Windows Server, HP-UX 11i, OpenVMS, NonStop, Red Hat Enterprise Linux and SUSE Linux Enterprise Server operating systems on Integrity servers.[1]

Early Integrity servers were based on two closely related chipsets. The zx1 chipset supported up to 4 CPUs and up to 8 PCI-X busses. They consisted of three distinct application-specific integrated circuits; a memory and I/O controller, a scalable memory adapter and an I/O adapter. The PA-8800 and PA-8900 microprocessors use the same bus as the Itanium 2 processors, allowing HP to also use this chipset for the HP 9000 servers and C8000 workstations.

The memory and I/O controller can be attached directly to up to 12 DDR SDRAM slots. If more slots than this are needed, two scalable memory adapters can be attached instead, allowing up to 48 memory slots. The chipset supports DIMM sizes up to 4 GB, theoretically allowing a machine to support up to 192 GB of RAM, although the largest supported configuration was 128 GB.

The sx1000 chipset supported up to 64 CPUs and up to 192 PCI-X buses. The successor chipsets are the zx2 and sx2000 respectively.

Entry-level servers

rx1600 series

The 1U rx1600 server is based on the zx1 chipset and has support for one or two 1 GHz Deerfield Itanium 2 CPUs. The 1U rx1620 server is based on the zx1 chipset and has support for one or two 1.3/1.6 GHz Fanwood Itanium 2 CPUs.

Common for the series is:

Optional features are:

The series support five operating systems:

rx2600 series

The 2U rx2600 server is based on the zx1 chipset and has support for one or two 1.0/1.4 GHz Deerfield/Madison, 1.3 GHz Madison or 1.5 GHz Madison CPUs. The 2U rx2620 server is based on the zx1 chipset and has support for one or two 1.6 GHz Fanwood/Madison or 1.4/1.6 GHz Montecito CPUs. The 2U rx2660 server is based on the zx2 chipset and has support for one or two 1.6 GHz Montvale or 1.42/1.66 GHz Montvale CPUs.

Common for the series is:

Optional features are:

The series support four operating systems:

rx2800 series

The 2U rx2800 i2 server used the Intel Itanium 9300 series chipset with 8, 4 or 2 processor cores available. Among features common for the series:[2]

The series supports three operating systems: HP-UX 11i v3, OpenVMS v 8.4 for Itanium, and Windows Server for Itanium.

rx3600

The 4U rx3600 is based on the zx2 chipset and has two CPU sockets which support Montecito or Montvale processors. It supports up to 96 GB of main memory, using 24 four-gigabyte DIMMs.

Standard features include:

Optional features:

rx4600 series

The 7U rx4610 utilizes Itanium 1 CPUs with support for up to four single-core CPUs, 64GB RAM and 10 PCI 64-bit slots. The 4U rx4640 utilizes Itanium 2 CPUs with support for up to four dual-core CPUs, 128 GB RAM and 6 PCI-X slots.

Both of these models come with integrated USB and video as default, which enables support for Microsoft Windows operating systems. The rx4640 is architecturally the same box as the rp4440, and can be changed from PA-RISC to Itanium 2 support with the flip of a switch.

rx5670

The discontinued 7U rx5670 server has four CPU sockets which support McKinley and Madison processors. It is zx1-based and can have up to 48 DIMM slots, supporting 256 MB to 2 GB DIMMs which must be loaded in matched sets of four (quads). It has 9 PCI-X slots and 1 PCI slot available.

rx6600

The 7U rx6600 is based on the zx2 chipset and has four CPU sockets that support Montecito and Montvale CPUs. It supports 384 GB memory using 48 eight-gigabyte DIMMs.

Standard features include:

Optional features:

Mid-range servers

HP Integrity rx7640 servers

HP's mid-range and high-end (Superdome) servers are based on cell boards, sometimes called cells,[3] which contain the chipset, Processors, memory, and I/O bus. This design allows the servers to be divided into hardware partitions, or groups of cell boards. Each partition is able to perform as if it were a separate server.

rx7600 series

The 10U rx7620 is based on the SX1000 chipset which supports both PA-RISC and Itanium 2 CPUs. The 10U rx7640 is based on the SX2000 chipset which supports both PA-RISC and Itanium 2 CPUs.

The rx7600 series are the smallest cell-based servers from HP. Just like the bigger rx8600 (see below) and the HP Superdome (see below), these servers can be partitioned, either as one big partition (two cells in one partition) or as two independent cells.

rx8600 series

The 17U rx8620 is based on the SX1000 chipset which supports both PA-RISC and Itanium 2 CPUs. The 17U rx8640 is based on the SX2000 chipset which supports both PA-RISC and Itanium 2 CPUs.

Just like the smaller rx7600 (see above) and the HP Superdome (see below), the rx8600 can be partitioned using any combination of the four available cell boards (minimum of one, maximum of four separated partitions).

The maximum number of partitions is four when used with an I/O-expander unit. Because each partition requires an available I/O slot, and the rx8600 series' integrated I/O-chassis statically maps its two I/O slots to cell board 0 and 1, an rx8600 series system is limited to two partitions unless an IOX is installed.

Cells can be freely moved from a rx7600 series to a rx8600 series as long as the chipset is the same on the cells, and the firmware is compatible.

High-end servers

Superdome

Main article: HP Superdome

The Superdome server is available in several models, including the SD-16, SD-32, and SD-64. HP announced Superdome 2 in April 2010, offering resiliency improvements, a modular, bladed design, common components and crossbar fabric that routes transactions to the optimal pathway between blades and I/O.[4] Superdome 2 addresses requirements for high-performance computing by providing flexible scalability and fault tolerance necessary for mission-critical workloads.[5]

In November 2011 HP announced Project Odyssey, a development roadmap to unify server architectures on a single platform. The roadmap includes blades with Intel Xeon processors for the HP Superdome 2 enclosure (code name “DragonHawk”) and the scalable c-Class blade enclosures (code named “HydraLynx”), while supporting Windows and Linux environments with features from HP-UX within the next two years.[6]

References

External links