Fillet weld

Fillet welding refers to the process of joining two pieces of metal together whether they be perpendicular or at an angle. These welds are commonly referred to as Tee joints which are two pieces of metal perpendicular to each other or Lap joints which are two pieces of metal that overlap and are welded at the edges. The weld is aesthetically triangular in shape and may have a concave, flat or convex surface depending on the welder’s technique. Welders use fillet welds when connecting flanges to pipes, welding cross sections of infrastructure, and when fastening metal by bolts isn't strong enough.[1]

Making a fillet weld with gas metal arc welding

Aspects

Parts of a fillet weld

There are 5 pieces to each Fillet weld known as the Root, Toe, Face, Leg and Throat.[2] The root of the weld is the part of deepest penetration which is the opposite angle of the Hypotenuse. The toes of the weld are essentially the edges or the points of the hypotenuse. The face of the weld is the outer visual or hypotenuse that you see when looking at a fillet weld. The legs are the opposite and adjacent sides to the triangular fillet weld. The leg length is usually designated as the size of the weld. The throat of the weld is the distance from the center of the face to the root of the weld. Typically the depth of the throat should be at least as thick as the thickness of metal you are welding.[1]

Notation

Fillet weld notation
Intermittent fillet welds

Fillet welding notation is important to recognize when reading blueprints. The use of this notation tells the welder exactly what is expected from the manufacturer. The symbol for a fillet weld is in the shape of a triangle. This triangle will lay either below a flat line or above it with an arrow coming off of the flat line pointing to a joint. If the triangle is positioned below the line, then the weld is going to be on the arrow side. If the triangle is positioned above the line then the weld is going to be on the opposite side of the arrow. When you find an arrow pointing to a joint with two triangles, one sitting below and one sitting above the line even with each other, then there is intended to be a fillet weld on the arrow side of the joint as well as the opposite side of the joint.[3] If the weld is to be continuous around a piece of metal such as a pipe or square, then a small circle will be around the point where the flat line and arrow pointing to the joint are connected.[4] Manufacturers also include the strength that the weld must be. This is indicated by a letter and number combination just before the flat line. Examples of this are "E70" meaning the arc electrode must have a tensile strength of 70,000 pounds-force per square inch (480,000 kPa; 4,900 kgf/cm2). There are also symbols that describe the aesthetics of the weld. A gentle curve pointing away from the hypotenuse means a concave weld is required, a straight line parallel with the hypotenuse calls for a flat faced weld, and a gentle curve towards the hypotenuse calls for a convex weld. The surface of the weld can be manipulated either by welding technique or by use of machining or grinding tools after the weld is completed. When reading a manufacturers blueprints, you might also come across weld dimensions. The weld can be sized in many different ways such as the length of the weld, the measurements of the legs of the weld, and the spaces between welds. Along with a triangle, there will usually be a size for the weld for example (1⁄8”x3⁄8”) to the left of the triangle. This means that the vertical leg of the weld is to be 1⁄8” whereas the horizontal leg is to 3⁄8”. To the right of the triangle, there will be a measurement of exactly how long the weld is supposed to be.[5] If the measurements of the drawing are in mm the welds are likewise measured in mm. For example the weld would be 3 x 10, the mm being understood automatically.

Intermittent fillet welds

An intermittent fillet weld is one that is not continuous across a joint. These welds are portrayed as a set of two numbers to the right of the triangle instead of just one. The first number as mentioned earlier refers to the length of the weld. The second number, separated from the first by a “-”, refers to the pitch. The pitch is a measurement from midpoint to midpoint of the intermittent welds. Intermittent welding is used when either a continuous weld is not necessary, or when a continuous weld threatens the joint by warping. In some cases intermittent welds are staggered on both sides of the joint. In this case, the notation of the two triangles aren't directly on top of each other. Instead, the side of the joint to receive the first weld will have a triangle further to the left than the following side’s triangle notation. As an end result of alternating intermittent fillet welds at each side side, the space between welds on one side of the joint will be the midpoint of the opposite side’s weld.[6]

See also

Notes

  1. ↑ 1.0 1.1 Althouse p.185
  2. ↑ Hultenius p.3
  3. ↑ Althouse p.186-190
  4. ↑ Haque, pages 2-6
  5. ↑ Haque, p. 4
  6. ↑ Althouse p.189

References