Electrical resistivity and conductivity

This article is about electrical conductivity in general. For other types of conductivity, see Conductivity. For specific applications in electrical elements, see Electrical resistance and conductance.

Electrical resistivity (also known as resistivity, specific electrical resistance, or volume resistivity) is an intrinsic property that quantifies how strongly a given material opposes the flow of electric current. A low resistivity indicates a material that readily allows the movement of electric charge. Resistivity is commonly represented by the Greek letter ρ (rho). The SI unit of electrical resistivity is the ohm⋅metre (Ω⋅m)^[1]^[2]^[3] although other units like ohm⋅centimetre (Ω⋅cm) are also in use. As an example, if a 1 m × 1 m × 1 m solid cube of material has sheet contacts on two opposite faces, and the resistance between these contacts is 1 Ω, then the resistivity of the material is 1 Ω⋅m.

Electrical conductivity or specific conductance is the reciprocal of electrical resistivity, and measures a material's ability to conduct an electric current. It is commonly represented by the Greek letter σ (sigma), but κ (kappa) (especially in electrical engineering) or γ (gamma) are also occasionally used. Its SI unit is siemens per metre (S/m) and CGSE unit is reciprocal second (s⁻¹).

Another related quantity, widely used in the literature of plasma physics, is the magnetic diffusivity defined as $\eta=\rho/\mu_0\equiv 1/\sigma \mu_0$ where $\mu_0$ is the magnetic permeability. The unit of the magnetic diffusivity, in SI, is $mA^2 \Omega N^{-1}$ .

Definition

Resistors or conductors with uniform cross-section

A piece of resistive material with electrical contacts on both ends.

Many resistors and conductors have a uniform cross section with a uniform flow of electric current, and are made of one material. (See the diagram to the right.) In this case, the electrical resistivity ρ (Greek: rho) is defined as:

\rho = R \frac{A}{\ell}, \,\!

where

R is the electrical resistance of a uniform specimen of the material (measured in ohms, Ω)

$\ell$ is the length of the piece of material (measured in metres, m)

A is the cross-sectional area of the specimen (measured in square metres, m²).

The reason resistivity is defined this way is that it makes resistivity an intrinsic property, unlike resistance. All copper wires, irrespective of their shape and size, have approximately the same resistivity, but a long, thin copper wire has a much larger resistance than a thick, short copper wire. Every material has its own characteristic resistivity – for example, resistivity of rubber is far larger than copper's.

In a hydraulic analogy, passing current through a high-resistivity material is like pushing water through a pipe full of sand—while passing current through a low-resistivity material is like pushing water through an empty pipe. If the pipes are the same size and shape, the pipe full of sand has higher resistance to flow. Resistance, however, is not solely determined by the presence or absence of sand. It also depends on the length and width of the pipe: short or wide pipes have lower resistance than narrow or long pipes.

The above equation can be transposed to get Pouillet's law (named after Claude Pouillet):

R = \rho \frac{\ell}{A}. \,\!

The resistance of a given material increases with length, but decrease with increasing cross-sectional area. From the above equations, resistivity has SI units of ohm⋅metre. Other units like ohm⋅cm or ohm⋅inch are also sometimes used.

The formula $R = \rho \ell / A$ can be used to intuitively understand the meaning of a resistivity value. For example, if $A=1\text{m}^2$ and $\ell=1\text{m}$ (forming a cube with perfectly conductive contacts on opposite faces), then the resistance of this element in ohms is numerically equal to the resistivity of the material it is made of in ohm-meters. Likewise, a 1 ohm⋅cm material would have a resistance of 1 ohm if contacted on opposite faces of a 1 cm×1 cm×1 cm cube.

Conductivity σ (Greek: sigma) is defined as the inverse of resistivity:

\sigma=\frac{1}{\rho}. \,\!

Conductivity has SI units of siemens per meter (S/m).

General definition

The above definition was specific to resistors or conductors with a uniform cross-section, where current flows uniformly through them. A more basic and general definition starts from the fact that an electric field inside a material makes electric current flow. The electrical resistivity ρ is defined as the ratio of the electric field to the density of the current it creates:

\rho=\frac{E}{J}, \,\!

where

ρ is the resistivity of the conductor material (measured in ohm⋅metres, Ω⋅m),

E is the magnitude of the electric field (in volts per metre, V⋅m⁻¹),

J is the magnitude of the current density (in amperes per square metre, A⋅m⁻²),

in which E and J are inside the conductor.

Conductivity is the inverse:

\sigma=\frac{1}{\rho} = \frac{J}{E}. \,\!

For example, rubber is a material with large ρ and small σ—because even a very large electric field in rubber makes almost no current flow through it. On the other hand, copper is a material with small ρ and large σ—because even a small electric field pulls a lot of current through it.

Causes of conductivity

Band theory simplified

Filling of the electronic Density of states in various types of materials at equilibrium. Here the vertical axis is energy while the horizontal axis is the Density of states for a particular band in the material listed. In metals and semimetals the Fermi level E_F lies inside at least one band. In insulators and semiconductors the Fermi level is inside a band gap; however, in semiconductors the bands are near enough to the Fermi level to be thermally populated with electrons or holes.

Quantum mechanics states that electrons in an atom cannot take on any arbitrary energy value. Rather, the electrons must occupy fixed energy levels, and values between these levels are impossible. When a large number of such allowed energy levels are spaced close together (in energy-space)—i.e., have similar (minutely differing)—energies, we can talk about these energy levels together as an "energy band." There can be many such energy bands in a material, depending on the atomic number {number of electrons (if atom is neutral)} and their distribution (besides external factors like environmental modification of the energy bands).

The material's electrons seek to minimize the total energy in the material by going to low energy states; however, the Pauli exclusion principle means that they cannot all go to the lowest state. The electrons instead "fill up" the band structure starting from the bottom. The characteristic energy level up to which the electrons have filled is called the Fermi level. The position of the Fermi level with respect to the band structure is very important for electrical conduction: only electrons in energy levels near the Fermi level are free to move around since the electrons can easily jump among the partially occupied states in that region. In contrast, the low energy states are rigidly filled with a fixed number of electrons at all times, and the high energy states are empty of electrons at all times.

In metals there are many energy levels near the Fermi level, meaning that there are many electrons available to move. This is what causes the high electronic conductivity in metals.

An important part of band theory is that there may be forbidden bands in energy: energy intervals that contain no energy levels. In insulators and semiconductors, the number of electrons happens to be just the right amount to fill a certain integer number of low energy bands, exactly to the boundary. In this case, the Fermi level falls within a band gap. Since there are no available states near the Fermi level, and the electrons are not freely movable, the electronic conductivity is very low.

In metals

Like balls in a Newton's cradle, electrons in a metal quickly transfer energy from one terminal to another, despite their own negligible movement.

A metal consists of a lattice of atoms, each with an outer shell of electrons that freely dissociate from their parent atoms and travel through the lattice. This is also known as a positive ionic lattice.^[4] This 'sea' of dissociable electrons allows the metal to conduct electric current. When an electrical potential difference (a voltage) is applied across the metal, the resulting electric field causes electrons to drift towards the positive terminal. The actual drift velocity of electrons is very small, in the order of magnitude of a meter per hour. However, as the electrons are densely packed in the material, the electromagnetic field is propagated through the metal at the speed of light.^[5] The mechanism is similar to transfer of momentum of balls in a Newton's cradle.^[6]

Near room temperatures, metals have resistance. The primary cause of this resistance is the collision of electrons with the atoms that make up the crystal lattice. This acts to scatter electrons and lose their energy on collisions rather than on linear movement through the lattice. Also contributing to resistance in metals with impurities are the resulting imperfections in the lattice.^[7]

The larger the cross-sectional area of the conductor, the more electrons per unit length are available to carry the current. As a result, the resistance is lower in larger cross-section conductors. The number of scattering events encountered by an electron passing through a material is proportional to the length of the conductor. The longer the conductor, therefore, the higher the resistance. Different materials also affect the resistance.^[8]

In semiconductors and insulators

Main articles: Semiconductor and Insulator (electricity)

In metals, the Fermi level lies in the conduction band (see Band Theory, above) giving rise to free conduction electrons. However, in semiconductors the position of the Fermi level is within the band gap, approximately half-way between the conduction band minimum and valence band maximum for intrinsic (undoped) semiconductors. This means that at 0 kelvin, there are no free conduction electrons, and the resistance is infinite. However, the resistance continues to decrease as the charge carrier density in the conduction band increases. In extrinsic (doped) semiconductors, dopant atoms increase the majority charge carrier concentration by donating electrons to the conduction band or accepting holes in the valence band. For both types of donor or acceptor atoms, increasing dopant density reduces resistance. Hence, highly doped semiconductors behave metallically. At very high temperatures, the contribution of thermally generated carriers dominate over the contribution from dopant atoms, and the resistance decreases exponentially with temperature.

In ionic liquids/electrolytes

Main article: Conductivity (electrolytic)

In electrolytes, electrical conduction happens not by band electrons or holes, but by full atomic species (ions) traveling, each carrying an electrical charge. The resistivity of ionic liquids varies tremendously by the concentration – while distilled water is almost an insulator, salt water is a very efficient electrical conductor. In biological membranes, currents are carried by ionic salts. Small holes in the membranes, called ion channels, are selective to specific ions and determine the membrane resistance.

Superconductivity

Main article: Superconductivity

The electrical resistivity of a metallic conductor decreases gradually as temperature is lowered. In ordinary conductors, such as copper or silver, this decrease is limited by impurities and other defects. Even near absolute zero, a real sample of a normal conductor shows some resistance. In a superconductor, the resistance drops abruptly to zero when the material is cooled below its critical temperature. An electric current flowing in a loop of superconducting wire can persist indefinitely with no power source.^[9]

In 1986, researchers discovered that some cuprate-perovskite ceramic materials have a critical temperature above 90 K (−183 °C). Such a high transition temperature is theoretically impossible for a conventional superconductor, so the researchers named these conductors high-temperature superconductors. Liquid nitrogen boils at 77 K, facilitating many experiments and applications that are less practical at lower temperatures. In conventional superconductors, electrons are held together in pairs by an attraction mediated by lattice phonons. The best available model of high-temperature superconductivity is still somewhat crude. There is a hypothesis that electron pairing in high-temperature superconductors is mediated by short-range spin waves known as paramagnons.^[10]

Plasma

Main article: Plasma (physics)

Lightning is an example of plasma present at Earth's surface. Typically, lightning discharges 30,000 amperes at up to 100 million volts, and emits light, radio waves, X-rays and even gamma rays.^[11] Plasma temperatures in lightning can approach 28,000 Kelvin (28,000 °C) (50,000 °F) and electron densities may exceed 10²⁴ m⁻³.

Plasmas are very good electrical conductors and electric potentials play an important role. The potential as it exists on average in the space between charged particles, independent of the question of how it can be measured, is called the plasma potential, or space potential. If an electrode is inserted into a plasma, its potential generally lies considerably below the plasma potential, due to what is termed a Debye sheath. The good electrical conductivity of plasmas makes their electric fields very small. This results in the important concept of quasineutrality, which says the density of negative charges is approximately equal to the density of positive charges over large volumes of the plasma (n_e = <Z>n_i), but on the scale of the Debye length there can be charge imbalance. In the special case that double layers are formed, the charge separation can extend some tens of Debye lengths.

The magnitude of the potentials and electric fields must be determined by means other than simply finding the net charge density. A common example is to assume that the electrons satisfy the Boltzmann relation:

n_e \propto e^{e\Phi/k_BT_e}.

Differentiating this relation provides a means to calculate the electric field from the density:

\vec{E} = (k_BT_e/e)(\nabla n_e/n_e).

It is possible to produce a plasma that is not quasineutral. An electron beam, for example, has only negative charges. The density of a non-neutral plasma must generally be very low, or it must be very small. Otherwise, the repulsive electrostatic force dissipates it.

In astrophysical plasmas, Debye screening prevents electric fields from directly affecting the plasma over large distances, i.e., greater than the Debye length. However, the existence of charged particles causes the plasma to generate, and be affected by, magnetic fields. This can and does cause extremely complex behavior, such as the generation of plasma double layers, an object that separates charge over a few tens of Debye lengths. The dynamics of plasmas interacting with external and self-generated magnetic fields are studied in the academic discipline of magnetohydrodynamics.

Plasma is often called the fourth state of matter after solid, liquids and gases.^[12]^[13] It is distinct from these and other lower-energy states of matter. Although it is closely related to the gas phase in that it also has no definite form or volume, it differs in a number of ways, including the following:

Property	Gas	Plasma
Electrical conductivity	Very low: Air is an excellent insulator until it breaks down into plasma at electric field strengths above 30 kilovolts per centimeter.^[14]	Usually very high: For many purposes, the conductivity of a plasma may be treated as infinite.
Independently acting species	One: All gas particles behave in a similar way, influenced by gravity and by collisions with one another.	Two or three: Electrons, ions, protons and neutrons can be distinguished by the sign and value of their charge so that they behave independently in many circumstances, with different bulk velocities and temperatures, allowing phenomena such as new types of waves and instabilities.
Velocity distribution	Maxwellian: Collisions usually lead to a Maxwellian velocity distribution of all gas particles, with very few relatively fast particles.	Often non-Maxwellian: Collisional interactions are often weak in hot plasmas and external forcing can drive the plasma far from local equilibrium and lead to a significant population of unusually fast particles.
Interactions	Binary: Two-particle collisions are the rule, three-body collisions extremely rare.	Collective: Waves, or organized motion of plasma, are very important because the particles can interact at long ranges through the electric and magnetic forces.

Resistivity and conductivity of various materials

Main article: Electrical resistivities of the elements (data page)

A conductor such as a metal has high conductivity and a low resistivity.
An insulator like glass has low conductivity and a high resistivity.
The conductivity of a semiconductor is generally intermediate, but varies widely under different conditions, such as exposure of the material to electric fields or specific frequencies of light, and, most important, with temperature and composition of the semiconductor material.

The degree of doping in semiconductors makes a large difference in conductivity. To a point, more doping leads to higher conductivity. The conductivity of a solution of water is highly dependent on its concentration of dissolved salts, and other chemical species that ionize in the solution. Electrical conductivity of water samples is used as an indicator of how salt-free, ion-free, or impurity-free the sample is; the purer the water, the lower the conductivity (the higher the resistivity). Conductivity measurements in water are often reported as specific conductance, relative to the conductivity of pure water at 7002298140000000000♠25 °C. An EC meter is normally used to measure conductivity in a solution. A rough summary is as follows:

Material	Resistivity ρ (Ω·m)
Superconductors	0
Metals	10⁻⁸
Semiconductors	variable
Electrolytes	variable
Insulators	10¹⁶

This table shows the resistivity, conductivity and temperature coefficient of various materials at 20 °C (68 °F, 293 K)

Material	ρ (Ω·m) at 7002293140000000000♠20 °C	σ (S/m) at 7002293140000000000♠20 °C	Temperature coefficient^{[note 1]} (K⁻¹)	Reference
Carbon (graphene)	6992100000000000000♠1.00×10⁻⁸	7008100000000000000♠1.00×10⁸	-0.0002	^[15]
Silver	6992159000000000000♠1.59×10⁻⁸	7007630000000000000♠6.30×10⁷	0.0038	^[16]^[17]
Copper	6992168009999999999♠1.68×10⁻⁸	7007596000000000000♠5.96×10⁷	0.003862	^[18]
Annealed copper^{[note 2]}	6992172009999900000♠1.72×10⁻⁸	7007580000000000000♠5.80×10⁷	0.00393	^[19]
Gold^{[note 3]}	6992244000000000000♠2.44×10⁻⁸	7007410000000000000♠4.10×10⁷	0.0034	^[16]
Aluminium^{[note 4]}	6992281990000000000♠2.82×10⁻⁸	7007350000000000000♠3.50×10⁷	0.0039	^[16]
Calcium	6992336009999999999♠3.36×10⁻⁸	7007298000000000000♠2.98×10⁷	0.0041
Tungsten	6992560000000000000♠5.60×10⁻⁸	7007179000000000000♠1.79×10⁷	0.0045	^[16]
Zinc	6992590000000000000♠5.90×10⁻⁸	7007169000000000000♠1.69×10⁷	0.0037	^[20]
Nickel	6992699000000000000♠6.99×10⁻⁸	7007143000000000000♠1.43×10⁷	0.006
Lithium	6992928000000000000♠9.28×10⁻⁸	7007108000000000000♠1.08×10⁷	0.006
Iron	6993100000000000000♠1.00×10⁻⁷	7007100000000000000♠1.00×10⁷	0.005	^[16]
Platinum	6993106000000000000♠1.06×10⁻⁷	7006943000000000000♠9.43×10⁶	0.00392	^[16]
Tin	6993109000000000000♠1.09×10⁻⁷	7006917000000000000♠9.17×10⁶	0.0045
Carbon steel (1010)	6993143000000000000♠1.43×10⁻⁷	7006699000000000000♠6.99×10⁶		^[21]
Lead	6993220000000000000♠2.20×10⁻⁷	7006455000000000000♠4.55×10⁶	0.0039	^[16]
Titanium	6993420000000000000♠4.20×10⁻⁷	7006238000000000000♠2.38×10⁶	X
Grain oriented electrical steel	6993459999999999999♠4.60×10⁻⁷	7006217000000000000♠2.17×10⁶		^[22]
Manganin	6993482000000000000♠4.82×10⁻⁷	7006207000000000000♠2.07×10⁶	0.000002	^[23]
Constantan	6993490000000099999♠4.90×10⁻⁷	7006204000000000000♠2.04×10⁶	0.000008	^[24]
Stainless steel^{[note 5]}	6993690000000000000♠6.90×10⁻⁷	7006145000000000000♠1.45×10⁶		^[25]
Mercury	6993980000000099999♠9.80×10⁻⁷	7006102000000000000♠1.02×10⁶	0.0009	^[23]
Nichrome^{[note 6]}	6994110000000000000♠1.10×10⁻⁶	7005670000000000000♠6.7×10⁵	6996400000000000000♠0.0004	^[16]
GaAs	6997100000000000000♠1.00×10⁻³ to 7008100000000000000♠1.00×10⁸	6992100000000000000♠1.00×10⁻⁸ to 7003100000000000000♠10³		^[26]
Carbon (amorphous)	6996500000000000000♠5.00×10⁻⁴ to 6996800000000000000♠8.00×10⁻⁴	7003125000000000000♠1.25×10³ to 7003200000000000000♠2×10³	−0.0005	^[16]^[27]
Carbon (graphite)^{[note 7]}	6994249990000099999♠2.50×10⁻⁶ to 6994499990000099999♠5.00×10⁻⁶ //basal plane 6997300000000000000♠3.00×10⁻³ ⊥basal plane	7005200000000000000♠2.00×10⁵ to 7005300000000000000♠3.00×10⁵ //basal plane 7002330000000000000♠3.30×10² ⊥basal plane		^[28]
Carbon (diamond)	7012100000000000000♠1.00×10¹²	~6987100000000000000♠10⁻¹³		^[29]
Germanium^{[note 8]}	6999460000000000000♠4.60×10⁻¹	2.17	−0.048	^[16]^[17]
Sea water^{[note 9]}	6999200000000000000♠2.00×10⁻¹	7000480000000000000♠4.80		^[30]
Swimming pool water^{[note 10]}	6999333000000000000♠3.33×10⁻¹ to 6999400000000000000♠4.00×10⁻¹	6999250000000000000♠0.25 to 6999300000000000000♠0.30		^[31]
Drinking water^{[note 11]}	7001200000000000000♠2.00×10¹ to 7003200000000000000♠2.00×10³	6996500000000000000♠5.00×10⁻⁴ to 6998500000000000000♠5.00×10⁻²
Silicon^{[note 8]}	7002640000000000000♠6.40×10²	6997156000000000000♠1.56×10⁻³	3001250000000000000♠−0.075	^[16]
Wood (damp)	7003100000000000000♠1.00×10³ to 7004100000000000000♠1.00×10⁴	6996100000000000000♠10⁻⁴ to 6997100000000000000♠10⁻³		^[32]
Deionized water^{[note 12]}	7005180000000000000♠1.80×10⁵	6994550000000000000♠5.50×10⁻⁶		^[33]
Glass	7011100000000000000♠10.0×10¹⁰ to 7015100000000000000♠10.0×10¹⁴	6985100000000000000♠10⁻¹⁵ to 6989100009999900000♠10⁻¹¹	?	^[16]^[17]
Hard rubber	7013100000000000000♠1.00×10¹³	6986100009999900000♠10⁻¹⁴	?	^[16]
Wood (oven dry)	7014100000000000000♠1.00×10¹⁴ to 7016100000000000000♠1.00×10¹⁶	6984100000000000000♠10⁻¹⁶ to 6986100009999900000♠10⁻¹⁴		^[32]
Sulfur	7015100000000000000♠1.00×10¹⁵	6984100000000000000♠10⁻¹⁶	?	^[16]
Air	7016130000000000000♠1.30×10¹⁶ to 7016330000000000000♠3.30×10¹⁶	6985300000000000000♠3×10⁻¹⁵ to 6985800000000000000♠8×10⁻¹⁵		^[34]
PEDOT:PSS	6997100000000000000♠1.00×10⁻³ to 6999100000000000000♠1.00×10⁻¹	7001100000000000000♠1×10¹ to 7003100000000000000♠1×10³	?
Fused quartz	7017750000000000000♠7.50×10¹⁷	6982130000000000000♠1.30×10⁻¹⁸	?	^[16]
PET	7021100000000000000♠10.0×10²⁰	6979100009999999999♠10⁻²¹	?
Teflon	7023099999999900000♠10.0×10²² to 7025100000000000000♠10.0×10²⁴	6975100000000000000♠10⁻²⁵ to 6977100000000099999♠10⁻²³	?

The effective temperature coefficient varies with temperature and purity level of the material. The 20 °C value is only an approximation when used at other temperatures. For example, the coefficient becomes lower at higher temperatures for copper, and the value 0.00427 is commonly specified at 7002273140000099999♠0 °C.^[35]

The extremely low resistivity (high conductivity) of silver is characteristic of metals. George Gamow tidily summed up the nature of the metals' dealings with electrons in his science-popularizing book, One, Two, Three...Infinity (1947): "The metallic substances differ from all other materials by the fact that the outer shells of their atoms are bound rather loosely, and often let one of their electrons go free. Thus the interior of a metal is filled up with a large number of unattached electrons that travel aimlessly around like a crowd of displaced persons. When a metal wire is subjected to electric force applied on its opposite ends, these free electrons rush in the direction of the force, thus forming what we call an electric current." More technically, the free electron model gives a basic description of electron flow in metals.

Wood is widely regarded as an extremely good insulator, but its resistivity is sensitively dependent on moisture content, with damp wood being a factor of at least 7010100000000000000♠10¹⁰ worse insulator than oven-dry.^[32] In any case, a sufficiently high voltage – such as that in lightning strikes or some high-tension powerlines – can lead to insulation breakdown and electrocution risk even with apparently dry wood.

Temperature dependence

Linear approximation

The electrical resistivity of most materials changes with temperature. If the temperature T does not vary too much, a linear approximation is typically used:

\rho(T) = \rho_0[1+\alpha (T - T_0)]

where $\alpha$ is called the temperature coefficient of resistivity, $T_0$ is a fixed reference temperature (usually room temperature), and $\rho_0$ is the resistivity at temperature $T_0$ . The parameter $\alpha$ is an empirical parameter fitted from measurement data. Because the linear approximation is only an approximation, $\alpha$ is different for different reference temperatures. For this reason it is usual to specify the temperature that $\alpha$ was measured at with a suffix, such as $\alpha_{15}$ , and the relationship only holds in a range of temperatures around the reference.^[36] When the temperature varies over a large temperature range, the linear approximation is inadequate and a more detailed analysis and understanding should be used.

Metals

In general, electrical resistivity of metals increases with temperature. Electron–phonon interactions can play a key role. At high temperatures, the resistance of a metal increases linearly with temperature. As the temperature of a metal is reduced, the temperature dependence of resistivity follows a power law function of temperature. Mathematically the temperature dependence of the resistivity ρ of a metal is given by the Bloch–Grüneisen formula:

\rho(T)=\rho(0)+A\left(\frac{T}{\Theta_R}\right)^n\int_0^{\frac{\Theta_R}{T}}\frac{x^n}{(e^x-1)(1-e^{-x})}dx

where $\rho(0)$ is the residual resistivity due to defect scattering, A is a constant that depends on the velocity of electrons at the Fermi surface, the Debye radius and the number density of electrons in the metal. $\Theta_R$ is the Debye temperature as obtained from resistivity measurements and matches very closely with the values of Debye temperature obtained from specific heat measurements. n is an integer that depends upon the nature of interaction:

n=5 implies that the resistance is due to scattering of electrons by phonons (as it is for simple metals)
n=3 implies that the resistance is due to s-d electron scattering (as is the case for transition metals)
n=2 implies that the resistance is due to electron–electron interaction.

If more than one source of scattering is simultaneously present, Matthiessen's Rule (first formulated by Augustus Matthiessen in the 1860s) ^[37]^[38] says that the total resistance can be approximated by adding up several different terms, each with the appropriate value of n.

As the temperature of the metal is sufficiently reduced (so as to 'freeze' all the phonons), the resistivity usually reaches a constant value, known as the residual resistivity. This value depends not only on the type of metal, but on its purity and thermal history. The value of the residual resistivity of a metal is decided by its impurity concentration. Some materials lose all electrical resistivity at sufficiently low temperatures, due to an effect known as superconductivity.

An investigation of the low-temperature resistivity of metals was the motivation to Heike Kamerlingh Onnes's experiments that led in 1911 to discovery of superconductivity. For details see History of superconductivity.

Semiconductors

Main article: Semiconductor

In general, intrinsic semiconductor resistivity decreases with increasing temperature. The electrons are bumped to the conduction energy band by thermal energy, where they flow freely, and in doing so leave behind holes in the valence band, which also flow freely. The electric resistance of a typical intrinsic (non doped) semiconductor decreases exponentially with temperature:

\rho= \rho_0 e^{-aT}\,

An even better approximation of the temperature dependence of the resistivity of a semiconductor is given by the Steinhart–Hart equation:

1/T = A + B \ln(\rho) + C (\ln(\rho))^3 \,

where A, B and C are the so-called Steinhart–Hart coefficients.

This equation is used to calibrate thermistors.

Extrinsic (doped) semiconductors have a far more complicated temperature profile. As temperature increases starting from absolute zero they first decrease steeply in resistance as the carriers leave the donors or acceptors. After most of the donors or acceptors have lost their carriers the resistance starts to increase again slightly due to the reducing mobility of carriers (much as in a metal). At higher temperatures it behaves like intrinsic semiconductors as the carriers from the donors/acceptors become insignificant compared to the thermally generated carriers.^[39]

In non-crystalline semiconductors, conduction can occur by charges quantum tunnelling from one localised site to another. This is known as variable range hopping and has the characteristic form of

\rho = A\exp(T^{-1/n})

where n = 2, 3, 4, depending on the dimensionality of the system.

Complex resistivity and conductivity

When analyzing the response of materials to alternating electric fields (dielectric spectroscopy), in applications such as electrical impedance tomography,^[40] it is necessary to replace resistivity with a complex quantity called impeditivity (in analogy to electrical impedance). Impeditivity is the sum of a real component, the resistivity, and an imaginary component, the reactivity (in analogy to reactance). The magnitude of impeditivity is the square root of sum of squares of magnitudes of resistivity and reactivity.

Conversely, in such cases the conductivity must be expressed as a complex number (or even as a matrix of complex numbers, in the case of anisotropic materials) called the admittivity. Admittivity is the sum of a real component called the conductivity and an imaginary component called the susceptivity.

An alternative description of the response to alternating currents uses a real (but frequency-dependent) conductivity, along with a real permittivity. The larger the conductivity is, the more quickly the alternating-current signal is absorbed by the material (i.e., the more opaque the material is). For details, see Mathematical descriptions of opacity.

Tensor equations for anisotropic materials

Some materials are anisotropic, meaning they have different properties in different directions. For example, a crystal of graphite consists microscopically of a stack of sheets, and current flows very easily through each sheet, but moves much less easily from one sheet to the next.^[28]

For an anisotropic material, it is not generally valid to use the scalar equations

J = \sigma E \,\, \rightleftharpoons \,\, E = \rho J . \,\!

For example, the current may not flow in exactly the same direction as the electric field. Instead, the equations are generalized to the 3D tensor form^[41]^[42]

\mathbf{J} = \sigma \mathbf{E} \,\, \rightleftharpoons \,\, \mathbf{E} = \rho \mathbf{J} \,\!

where the conductivity σ and resistivity ρ are rank-2 tensors (in other words, 3×3 matrices). The equations are compactly illustrated in component form (using index notation and the summation convention):^[43]

J_i = \sigma_{ij} E_j \,\, \rightleftharpoons \,\, E_i = \rho_{ij} J_j . \,\!

The σ and ρ tensors are inverses (in the sense of a matrix inverse). The individual components are not necessarily inverses; for example, σ_xx may not be equal to 1/ρ_xx.

Resistance versus resistivity in complicated geometries

If the material's resistivity is known, calculating the resistance of something made from it may, in some cases, be much more complicated than the formula $R = \rho \ell /A$ above. One example is Spreading Resistance Profiling, where the material is inhomogeneous (different resistivity in different places), and the exact paths of current flow are not obvious.

In cases like this, the formulas

J = \sigma E \,\, \rightleftharpoons \,\, E = \rho J \,\!

must be replaced with

\mathbf{J}(\mathbf{r}) = \sigma(\mathbf{r}) \mathbf{E}(\mathbf{r}) \,\, \rightleftharpoons \,\, \mathbf{E}(\mathbf{r}) = \rho(\mathbf{r}) \mathbf{J}(\mathbf{r}), \,\!

where E and J are now vector fields. This equation, along with the continuity equation for J and the Poisson's equation for E, form a set of partial differential equations. In special cases, an exact or approximate solution to these equations can be worked out by hand, but for very accurate answers in complex cases, computer methods like finite element analysis may be required.

Resistivity density products

In some applications where the weight of an item is very important resistivity density products are more important than absolute low resistivity – it is often possible to make the conductor thicker to make up for a higher resistivity; and then a low resistivity density product material (or equivalently a high conductance to density ratio) is desirable. For example, for long distance overhead power lines, aluminium is frequently used rather than copper because it is lighter for the same conductance.

Material	Resistivity (nΩ·m)	Density (g/cm³)	Resistivity-density product (nΩ·m·g/cm³)	Resistivity-density relative to copper
Sodium	47.7	0.97	46	30.66˙%
Lithium	92.8	0.53	49	32.66˙%
Calcium	33.6	1.55	52	34.66˙%
Potassium	72.0	0.89	64	42.66˙%
Beryllium	35.6	1.85	66	44%
Aluminium	26.50	2.70	72	48%
Magnesium	43.90	1.74	76.3	50.86˙%
Copper	16.78	8.96	150	100%
Silver	15.87	10.49	166	110.66˙%
Gold	22.14	19.30	427	284.66˙%
Iron	96.1	7.874	757	504.66˙%

Silver, although it is the least resistive metal known, has a high density and does poorly by this measure. Calcium and the alkali metals have the best resistivity-density products, but are rarely used for conductors due to their high reactivity with water and oxygen. Aluminium is far more stable. Two other important attributes, price and toxicity, exclude the (otherwise) best choice: Beryllium. Thus, aluminium is usually the metal of choice when the weight or cost of a conductor is the driving consideration.

Notes

↑ The numbers in this column increase or decrease the significand portion of the resistivity. For example, at 30 °C (303 K), the resistivity of silver is 6992165000000000000♠1.65×10⁻⁸. This is calculated as Δρ = α ΔT ρ_o where ρ_o is the resistivity at 7002293140000000000♠20 °C (in this case) and α is the temperature coefficient.
↑ Referred to as 100% IACS or International Annealed Copper Standard. The unit for expressing the conductivity of nonmagnetic materials by testing using the eddy-current method. Generally used for temper and alloy verification of aluminium.
↑ Gold is commonly used in electrical contacts because it does not easily corrode.
↑ Commonly used for high voltage power lines
↑ 18% chromium/ 8% nickel austenitic stainless steel
↑ Nickel-iron-chromium alloy commonly used in heating elements.
↑ Graphite is strongly anisotropic.
↑ 8.0 8.1 The resistivity of semiconductors depends strongly on the presence of impurities in the material.
↑ Corresponds to an average salinity of 35 g/kg at 7002293140000000000♠20 °C.
↑ The pH should be around 8.4 and the conductivity in the range of 2.5 - 3 mS/cm. The lower value is appropriate for freshly prepared water. The conductivity is used for the determination of TDS (total dissolved particles).
↑ This value range is typical of high quality drinking water and not an indicator of water quality
↑ Conductivity is lowest with monatomic gases present; changes to 6996120000000000000♠1.2×10⁻⁴ upon complete de-gassing, or to 6995750000000000000♠7.5×10⁻⁵ upon equilibration to the atmosphere due to dissolved CO₂

References

↑ Lowrie. Fundamentals of Geophysics. Cambridge University Press. pp. 254–. ISBN 978-1-139-46595-3.
↑ Narinder Kumar (2003). Comprehensive Physics XII. Laxmi Publications. pp. 282–. ISBN 978-81-7008-592-8.
↑ Eric Bogatin (2004). Signal Integrity: Simplified. Prentice Hall Professional. pp. 114–. ISBN 978-0-13-066946-9.
↑ Bonding (sl). ibchem.com
↑ "Current versus Drift Speed". The physics classroom. Retrieved 20 August 2014.
↑ Lowe, Doug (2012). Electronics All-in-One For Dummies. John Wiley & Sons. ISBN 978-0-470-14704-7.
↑ "Current Electricity - Lesson 3 - Electrical Resistance". The physics classroom. Retrieved 20 August 2014.
↑ Suresh V Vettoor Electrical Conduction and Superconductivity. ias.ac.in. September 2003
↑ John C. Gallop (1990). SQUIDS, the Josephson Effects and Superconducting Electronics. CRC Press. pp. 3, 20. ISBN 0-7503-0051-5.
↑ D. Pines (2002). "The Spin Fluctuation Model for High Temperature Superconductivity: Progress and Prospects". The Gap Symmetry and Fluctuations in High-Tc Superconductors. NATO Science Series: B: 371. New York: Kluwer Academic. pp. 111–142. doi:10.1007/0-306-47081-0_7. ISBN 0-306-45934-5.
↑ See Flashes in the Sky: Earth's Gamma-Ray Bursts Triggered by Lightning
↑ Yaffa Eliezer, Shalom Eliezer, The Fourth State of Matter: An Introduction to the Physics of Plasma, Publisher: Adam Hilger, 1989, ISBN 978-0-85274-164-1, 226 pages, page 5
↑ Bittencourt, J.A. (2004). Fundamentals of Plasma Physics. Springer. p. 1. ISBN 9780387209753.
↑ Hong, Alice (2000). "Dielectric Strength of Air". The Physics Factbook.
↑ Physicists Show Electrons Can Travel More Than 100 Times Faster in Graphene. Newsdesk.umd.edu (2008-03-24). Retrieved on 2014-02-03.
↑ 16.0 16.1 16.2 16.3 16.4 16.5 16.6 16.7 16.8 16.9 16.10 16.11 16.12 16.13 16.14 Raymond A. Serway (1998). Principles of Physics (2nd ed.). Fort Worth, Texas; London: Saunders College Pub. p. 602. ISBN 0-03-020457-7.
↑ 17.0 17.1 17.2 David Griffiths (1999) [1981]. "7. Electrodynamics". In Alison Reeves. Introduction to Electrodynamics (3rd ed.). Upper Saddle River, New Jersey: Prentice Hall. p. 286. ISBN 0-13-805326-X. OCLC 40251748. |accessdate= requires |url= (help)
↑ Douglas Giancoli (2009) [1984]. "25. Electric Currents and Resistance". In Jocelyn Phillips. Physics for Scientists and Engineers with Modern Physics (4th ed.). Upper Saddle River, New Jersey: Prentice Hall. p. 658. ISBN 0-13-149508-9. |accessdate= requires |url= (help)
↑ Copper wire tables : United States. National Bureau of Standards : Free Download & Streaming : Internet Archive. Archive.org (2001-03-10). Retrieved on 2014-02-03.
↑ Physical constants. (PDF format; see page 2, table in the right lower corner)]. Retrieved on 2011-12-17.
↑ AISI 1010 Steel, cold drawn. Matweb
↑ "JFE steel" (PDF). Retrieved 2012-10-20.
↑ 23.0 23.1 Douglas C. Giancoli (1995). Physics: Principles with Applications (4th ed.). London: Prentice Hall. ISBN 0-13-102153-2.
(see also Table of Resistivity. hyperphysics.phy-astr.gsu.edu)
↑ John O'Malley (1992) Schaum's outline of theory and problems of basic circuit analysis, p. 19, McGraw-Hill Professional, ISBN 0-07-047824-4
↑ Glenn Elert (ed.), "Resistivity of steel", The Physics Factbook, retrieved and archived 16 June 2011.
↑ Milton Ohring (1995). Engineering materials science, Volume 1 (3rd ed.). Academic Press. p. 561. ISBN 0125249950.
↑ Y. Pauleau, Péter B. Barna, P. B. Barna (1997) Protective coatings and thin films: synthesis, characterization, and applications, p. 215, Springer, ISBN 0-7923-4380-8.
↑ 28.0 28.1 Hugh O. Pierson, Handbook of carbon, graphite, diamond, and fullerenes: properties, processing, and applications, p. 61, William Andrew, 1993 ISBN 0-8155-1339-9.
↑ Lawrence S. Pan, Don R. Kania, Diamond: electronic properties and applications, p. 140, Springer, 1994 ISBN 0-7923-9524-7.
↑ Physical properties of sea water. Kayelaby.npl.co.uk. Retrieved on 2011-12-17.
↑ . chemistry.stackexchange.com
↑ 32.0 32.1 32.2 Transmission Lines data. Transmission-line.net. Retrieved on 2014-02-03.
↑ R. M. Pashley , M. Rzechowicz, L. R. Pashley, and M. J. Francis (2005). "De-Gassed Water is a Better Cleaning Agent". The Journal of Physical Chemistry B 109 (3): 1231–8. doi:10.1021/jp045975a. PMID 16851085.
↑ S. D. Pawar, P. Murugavel, D. M. Lal (2009). "Effect of relative humidity and sea level pressure on electrical conductivity of air over Indian Ocean". Journal of Geophysical Research 114: D02205. Bibcode:2009JGRD..11402205P. doi:10.1029/2007JD009716.
↑ Copper Wire Tables. US Dep. of Commerce. National Bureau of Standards Handbook. February 21, 1966
↑ M.R. Ward (1971) Electrical Engineering Science, pp. 36–40, McGraw-Hill.
↑ A. Matthiessen, Rep. Brit. Ass. 32, 144 (1862)
↑ A. Matthiessen, Progg. Anallen, 122, 47 (1864)
↑ J. Seymour (1972) Physical Electronics, chapter 2, Pitman
↑ Otto H. Schmitt, University of Minnesota Mutual Impedivity Spectrometry and the Feasibility of its Incorporation into Tissue-Diagnostic Anatomical Reconstruction and Multivariate Time-Coherent Physiological Measurements. otto-schmitt.org. Retrieved on 2011-12-17.
↑ J.R. Tyldesley (1975) An introduction to Tensor Analysis: For Engineers and Applied Scientists, Longman, ISBN 0-582-44355-5
↑ G. Woan (2010) The Cambridge Handbook of Physics Formulas, Cambridge University Press, ISBN 978-0-521-57507-2
↑ K.F. Riley, M.P. Hobson, S.J. Bence (2010) Mathematical methods for physics and engineering, Cambridge University Press, ISBN 978-0-521-86153-3

External links

"Electrical Conductivity". Sixty Symbols. Brady Haran for the University of Nottingham. 2010.