Data I/O

Data I/O
Public (NASDAQ: DAIO)
Founded 1969
Headquarters Redmond, Washington, United States
Website www.dataio.com

Data I/O Corporation is a manufacturer of programming and automated device handling systems for programmable integrated circuits. The company is headquartered in Redmond, Washington with sales and engineering offices worldwide.[1]

History

Data I/O was incorporated in 1969.[2] Before the IBM PC was introduced, the company developed equipment that allowed electronic designers to program the very first non-volatile semiconductor devices with data stored on punched cards or ASCII-encoded (eight-level) punched paper tape. Over the next three decades the company rode the non-volatile technology wave forward as Bi-Polar, EPROM, EEPROM, NOR FLASH, Antifuse, FRAM and, most recently, NAND FLASH devices were introduced by a myriad of semiconductor vendors.

While not manufacturing any semiconductors itself, Data I/O's core business is the design and manufacture of equipment that transfers data into various non-volatile semiconductor devices. In modern times, these devices commonly fall into three categories: Flash Memory, Microcontroller devices, and Programmable Logic Devices.

Current Products

Introduced in 2000, Data I/O FlashCORE technology is optimized for programming of NAND and NOR based Flash memory devices and Flash-based microcontrollers and is sold in FlashPAK, PS-System, FLX500, and ProLINE-RoadRunner programmer models spanning engineering use to high-volume offline and inline "just-in-time" manufacturing. Data I/O provides Tasklink for Windows software to set up FlashCORE programmers and specify data sources. In addition, they develop software that manages automated and remote programming, secures data, and manages device serialization. Many of these work with TaskLink while others are independent software packages.

Data I/O manufactures two programmers which can accommodate DIP (through-hole) devices. These would be the Plus-48 and the Optima. Both are aimed at the small, (relatively) low-cost, desktop programmer (engineering) market.

Legacy Products

Data I/O Model 29B Universal Programmer with a UniPak 2

Data I/O has a rich history of programmer models, representing an evolution of the technology from which programmable devices were created. One of their first attempts at a 'Universal' programmer was the Model 1, Model 5 (TTL-Sequencer based), Model 9 (Microprocessor based),and the System 19 (introduced in the late 1970s). It utilized a variety of interchangeable device sockets and configuration plug-in printed-circuit cards, consisting mainly of resistors, diodes and jumpers, to allow reading and programming of a wider variety of memory devices than had previously been achieved.

The early 1980s saw the introduction of the System 29 series. The first model in this family, the 29A, added more user RAM, and eliminated the need for configuration cards by offering keypad-programmable 'Family' and 'Pinout' codes to configure the programmer for a still-wider range of devices. Introduced along with the 29A was the 'Unipak,' a large plug-in adapter which featured several different sizes of ZIF sockets to reduce the need for changing socket modules. Since the Unipak was limited to dealing with memory devices, an additional accessory series, called the 'LogicPak,' was introduced to handle programmable logic devices (PALs, GALs, etc.)

Later models feature both a series of fixed sockets and an interchangeable socket module in one housing. Memory devices up to 40 pins in size could be read or programmed with the simple installation of the appropriate socket module. The 29B chassis could accommodate up to 1MB of user RAM.

Around 1987, Data I/O made a major leap forward by introducing the first of the 'Unifamily' programmers in the form of the 'Unisite.' This was their first engineering programmer to feature software-programmable pin drivers, a technology which allows any pin of the device socket to be configured, through software, for power, ground, or nearly any type of programming waveform. The first model in this line, the Unisite-40, featured a removable module with a single 40-pin DIP ZIF socket, called the SITE-40, and space to install optional programming adapters to the right of this DIP module. Such modules included the 'SetSite,' a module containing eight 40-pin ZIF sockets to allow gang programming of up to eight identical memory devices, and the 'ChipSite,' an early multi-socket module accommodating several sizes of PLCC and SOIC DIP packages with 'clamshell' ZIF sockets.

The final successor to the ChipSite unit was the PinSite. This featured a universal programming base which could accept a variety of socket adapters, including those for chips packaged in PGA, QFP, TSOP, and many others. There was even a special connection module made available which could, through the Pinsite's base, allow the Unisite to serve as the programming source in automated device handlers in factory floor environments.

The Unifamily was also the first series of Data I/O's programmers to feature a built-in user menu in their operating software. All the programmer required for basic operation was a dumb terminal, hooked up via an RS232 serial port. Facilities were also provided for computer-based remote control via a second serial port.

As for operating software, the early Unifamily all booted and ran from software stored on 720k floppy diskettes (in the case of the Unisite) or on 1.44MB floppies (in the case of other Unifamily members). This software consists of the operator's menu system, self-test routines, and device algorithms. Later in production, an option for installation of a miniature hard drive was provided (See MSM, or Mass Storage Module, below). The Unisite is the only programmer which still requires true 720k floppies for non-MSM operation, or updating the MSM's software without the aid of external PC-based software.

The Unisite was truly the flagship model of the Unifamily line, selling for over $35,000 new in a typical configuration and staying in active production for at least 20 years. Data I/O, in an effort to make the Unifamily line more attractive to companies with tighter budgets, introduced several other programmers utilizing the same programmable pin-driver technology as the Unisite, all selling for (typically) under $10,000 new. These included the model 2900, 3900, 3980, and 3980XPi. These units varied in capabilities, primarily in terms of the number of pin drivers they came with. The basic 2900 featured 44 drivers, while the 39xx series all had 88. Data I/O developed a proprietary multiplexing scheme which allowed Unifamily programmers, equipped with their maximum number of hardware pin drivers, to handle devices with up to 240 pins.

Other differences in the series are minor. They all share a common base design, in terms of their pin-driver technology, and they all feature the ability to boot and run from floppy diskettes and provide an internal menu.

The differences are primarily in features. The Unisite, within less than a year of entering production, was revised in the form of a new DIP module, referred to as the 'Site48.' As its name implies, this adapter had 48 pins in its DIP socket, and remained the standard for many years. Its successor, the Site48-HS, is functionally identical to the Site48, but utilizes solid-state switching for the socket pins instead of the electromechanical relays present in earlier adapters. The 2900 and 39xx series used electromechanical relays throughout their production life.

The Unisites also featured 512K of user RAM, standard. Field-installable upgrade kits, consisting of a separate memory board, an appropriate number of 30-pin SIMMs, a mounting bracket and interconnecting cable, were made available to upgrade these early units to 1MB or 8MB, depending on the user's budget. As an example, the price for the 8MB upgrade kit was around $495 in the mid-1990s. These early kits required considerable labor to install, including extensive disassembly of the programmer, as the memory board was designed to mount under the main circuit board.

In response to these difficulties, as well as improvements in available technology, the Unisite's main circuit board soon received some major revisions. These included the removal of most of the DIP-based DRAM chips, and the addition of two 30-pin memory module sockets on the main board itself. With these changes, upgrading the programmer's available RAM became much easier, requiring only the removal of the top cover, installation of two SIMMs, and replacing one PAL chip.

The MSM (Mass Storage Module)

The revisions to the UniSite's main board were also done to support a new option. Around the same time, Data I/O created the 'MSM,' or Mass Storage Module. This consisted of an additional circuit board containing a miniature hard disk drive (either a 2.5 inch PATA/IDE device or a PCMCIA Type III card drive, depending on the MSM's revision level) and appropriate interface circuitry. All the programmer's operating software and device algorithms could be transferred to the MSM's drive in less than a half-hour, rendering the programmer completely independent from floppy diskettes.

The MSM option is still available today, though it takes a very different form. The last and latest revision of this device is entirely solid-state, consisting of a single large FPGA chip as the board's glue logic, an SPROM (Serial Programmable Read-Only Memory) chip, containing the FPGA's operating code, a few SRAM chips for buffering and a solid-state or 'Flash' drive.

The MSM was (and still is) an optional, field-installable module for the 3900 and Unisite. Unisite programmers require 8MB of user RAM and controller board revision 701-2313-00 or higher to utilize this option. In addition, the MSM will not function with Unifamily operating software revisions below 6.6.

There has been recent (2011) discussion, on the Yahoo Groups forum Data_IO_EPROM, regarding plans for a do-it-yourself MSM. The information package is said to be available in the group's file area on Yahoo, and it has also been said the device is considerably less expensive to build than Data I/O's option kit.

All 3900 series programmers are MSM-compatible at the hardware level. Again, however, recognition and use of the MSM in software requires Unifamily version 6.6 or above. Successful installation of the MSM in a 3900 programmer automatically turns it into the model 3980.

Addition of the MSM option also adds another option, if one is technically inclined enough to create the cabling and connectors required to use it: A high-speed parallel port interface which supplements the programmer's serial port. When used in conjunction with a Windows-based PC, and Data I/O's TaskLink software, the parallel port greatly enhances the speed of data transfers to and from the programmer. As one example, a 1MB data file takes at least two minutes to be transferred into or out of a Unifamily programmer via the serial port at its highest available speed (19200 baud). The same file, transferred with the parallel port's help, takes around 30–40 seconds.

Any Unifamily programmer with 'XPi' after its name (Unisite-XPi, 3980-XPi) will, unless someone has manually removed it, already have the MSM and parallel port options installed as standard equipment. These programmers represent the last and latest of the Unifamily line and, although no longer in production, are still considered fully supported by Data I/O.

References

  1. ↑ http://www.data-io.com/corporate/about.asp
  2. ↑ DAIO: Profile for DATA IO CP - Yahoo! Finance

External links