Custer Channel Wing

CCW-5 Channel Wing
Front view of the second CCW-5 preserved by the Mid-Atlantic Air Museum in Reading, Pennsylvania
Role Experimental aircraft
National origin United States
Manufacturer Custer Channel Wing Corporation
Designer Willard Ray Custer
First flight 13 July 1953
Introduction 1953
Status preserved in a museum
Produced 1953-1964
Number built 2
Developed from CCW-1 Channel Wing

The Custer Channel Wing was a series of American-built experimental aircraft designs of the 1940s and 1950s incorporating a half-barrel shaped section to each wing.

Initial design

Willard Custer filed a United States patent in 1929 for a wing design incorporating a semi-circular channel or "half barrel" shape in which an engine was to be fitted in pusher mode. Custer claimed that this layout, the channel wing, which gave STOL operating capabilities, resulted in a design "which is an aircraft not an airplane. It does not plane the air to fly, rather it brings the air to the lift surfaces and reduces pressure to fly at 8 to 11 mph"[1]

Development

CCW-1

The prototype Custer CCW-1 single-seat test aircraft displayed at the National Air and Space Museum facility at Silver Hill, Maryland in April 1982
Channel Wing concept testing at Langley

The first aircraft to incorporate Custer's concept was the CCW-1 which was fitted with a single-seat and was powered by two 75 h.p. Lycoming O-145 pusher engines. Registered NX30090 in the FAAs experimental category, the sole example first flew on 12 November 1942 during a solo flight that was quite unintentional. Custer, who was a non-pilot, taxied the aircraft in a demonstration for financial backers and it suddenly became airborne. A hard landing followed, and one landing gear collapsed, but this did not dampen his backers' enthusiasm.[1] This aircraft was donated to the National Air and Space Museum and displayed at Silver Hill, Maryland.[2]

The CCW-1 was test flown by Frank D. Kelley, who would become a partner in the National Aircraft Corporation with Custer. The Channelwing concept was demonstrated with scale wind tunnel tests for the Army Air forces in Dayton in June 1944, and again in 1946 with 53 different configurations.[3]

CCW-2

This was an evolution of the CCW-1 as a single-seat test bed and used an adapted uncovered fuselage of a Taylorcraft BC-12 light aircraft, replacing the single engine with two pusher engines fitted each side of the fuselage and placed within the wing channels.[4] The sole example N1375V first flew on 3 July 1948. It was flown for about 100 hours of testing with take-off and landing being made within 45–65 ft. Despite the claim of "flying better than a conventional aircraft" it was calculated that a stock Piper Cub was more efficient, lifting 18 lbs/h.p. versus the CCW-2s 11 lbs/h.p.[1] The CCW-3 and CCW-4 designations were not used.

CCW-5

Main article: Custer CCW-5

During the early 1950s, Custer formed the Custer Channel Wing Corporation to develop and build the five-seat CCW-5 design which was intended for commercial sale. The first example N6257C was designed by Custer but built by the Baumann Corporation of Santa Barbara, California. It utilised an adapted fuselage and tail assembly of a Baumann Brigadier. Power was from two pusher 225 h.p. Continental O-470 engines. The first flight was made on 13 July 1953.[1]

Rear view of the second CCW-5 showing the fixing of the pusher engine within the wing channels.

Custer persisted with his design and built the second example N5855V at the Custer Channel Wing Corp factory. It again used a Baumann Brigadier fuselage and tail assembly. Although several firms expressed interest in production of the design, all failed to provide sufficient funds. This aircraft first flew on 19 June 1964.[1]

The CCW-5 accommodated five persons, and its power plants are suspended in the centre of the 6 ft-chord wing channels on tubular frameworks attached to the wing spars. The aircraft draws air through the channels at high velocity, decreasing pressure over the wings and increasing lift. The CCW-5 was claimed to be capable of flying at a sustained speed of 35 mph.[5] Production deliveries were scheduled to commence during 1965, but this was never achieved.

Operational history

The CCW-5 continued to make developments flights during the 1960s and 1970s, but no production orders were obtained. The second example was donated to the Mid-Atlantic Air Museum at Reading Airport, Pennsylvania and is on restricted display.[6]

Specifications (CCW-5)

Data from Green, 1965, p.223

General characteristics

Performance

See also


Notes

  1. ↑ 1.0 1.1 1.2 1.3 1.4 aerofiles.com
  2. ↑ Ogden, 2007, p.298
  3. ↑ Kent A. Mitchell (Spring 1998). "Mr.Custer and His Channel Wing Airplanes". AAHS Journal.
  4. ↑ Flight, 4 January 1952
  5. ↑ Green, 1965, p.223
  6. ↑ Ogden, 2007, p.453

References

  • Green, William (1965). The Aircraft of the World. Macdonald & Co (Publishers Ltd.
  • Ogden, Bob (2007). Aviation Museums and Collections of North America. Air-Britain (Historians). ISBN 978-0-85130-385-7.

External links

Wikimedia Commons has media related to Custer Channel Wing.