Steam-assisted gravity drainage

Steam Assisted Gravity Drainage (SAGD) is an Enhanced oil recovery technology for producing heavy crude oil and bitumen. It is an advanced form of steam stimulation in which a pair of horizontal wells are drilled into the oil reservoir, one a few metres above the other. High pressure steam is continuously injected into the upper wellbore to heat the oil and reduce its viscosity, causing the heated oil to drain into the lower wellbore, where it is pumped out. Dr. Roger Butler, engineer at Imperial Oil from 1955 to 1982, invented the steam assisted gravity drainage (SAGD) in the 1970s. Butler "developed the concept of using horizontal pairs of wells and injected steam to develop certain deposits of bitumen considered too deep for mining. "^[1][2] In 1983 Butler became director of technical programs for the Alberta Oil Sands Technology and Research Authority (AOSTRA),^[1][3] a crown corporation created by Premier Lougheed to promote new technologies for oil sands and heavy crude oil production. AOSTRA quickly supported SAGD as a promising innovation in oil sands extraction technology.^[2]

Steam Assisted Gravity Drainage (SAGD) and Cyclic Steam Stimulation (CSS) are two commercially applied primal thermal recovery processes used in the oil sands (Jiang 2009)^[4] in Geological formation sub-units, such as Grand Rapids Formation, Clearwater Formation, McMurray Formation, General Petroleum Sand, Lloydminster Sand, of the Mannville Group, a Stratigraphic range in the Western Canadian Sedimentary Basin.

Canada is the single largest supplier of imported oil to the United States—even larger, despite popular conceptions, than Saudi Arabia, Venezuela, or Nigeria. There are two primary methods of oil sands recovery. The strip-mining technique is known best. However, the more recent steam-assisted gravity drainage technique (SAGD) is better suited to deeper deposits. Much of the future growth of production in the Canadian oil sands will be from SAGD.(Glassman & 2011 9)^[5]

Description

In the SAGD process, two parallel horizontal oil wells are drilled in the formation, one about 4 to 6 metres above the other. The upper well injects steam, and the lower one collects the heated crude oil or bitumen that flows out of the formation, along with any water from the condensation of injected steam. The basis of the process is that the injected steam forms a "steam chamber" that grows vertically and horizontally in the formation. The heat from the steam reduces the viscosity of the heavy crude oil or bitumen which allows it to flow down into the lower wellbore. The steam and gases rise because of their low density compared to the heavy crude oil below, ensuring that steamundefined is not produced at the lower production well. The gases released, which include methane, carbon dioxide, and usually some hydrogen sulfide, tend to rise in the steam chamber, filling the void space left by the oil and, to a certain extent, forming an insulating heat blanket above the steam. Oil and water flow is by a countercurrent, gravity driven drainage into the lower well bore. The condensed water and crude oil or bitumen is recovered to the surface by pumps such as progressive cavity pumps that work well for moving high-viscosity fluids with suspended solids.

Sub-cool is the difference between the saturation temperature (boiling point) of water at the producer pressure and the actual temperature at the same place where the pressure is measured. The higher the liquid level above the producer the lower the temperature and higher is the sub-cool. However real life reservoirs are invariably heterogeneous therefore it becomes extremely difficult to achieve a uniform sub-cool along the entire horizontal length of a well. As a consequence many operators, when faced with uneven stunted steam chamber development, allow a small quantity of steam to enter into the producer to keep the bitumen in the entire wellbore hot hence keeping its viscosity low with the added benefit of transferring heat to colder parts of the reservoir along the wellbore. Another variation sometimes called Partial SAGD is used when operators deliberately circulate steam in the producer following a long shut-in period or as a startup procedure. Though a high value of sub-cool is desirable from a thermal efficiency standpoint as it generally includes reduction of steam injection rates but it also results in slightly reduced production due to a corresponding higher viscosity and lower mobility of bitumen caused by lower temperature. Another drawback of very high sub-cool is the possibility of steam pressure eventually not being enough to sustain steam chamber development above the injector, sometimes resulting in collapsed steam chambers where condensed steam floods the injector and precludes further development of the chamber.

Operating the injection and production wells at approximately reservoir pressure eliminates the instability problems that plague all high-pressure steam processes and SAGD produces a smooth, even production that can be as high as 70% to 80% of oil in place in suitable reservoirs. The process is relatively insensitive to shale streaks and other vertical barriers to steam and fluid flow because, as the rock is heated, differential thermal expansion causes fractures in it, allowing steam and fluids to flow through. This allows recovery rates of 60% to 70% of oil in place, even in formations with many thin shale barriers. Thermally, SAGD is twice as efficient as the older cyclic steam stimulation (CSS) process, and it results in far fewer wells being damaged by high pressure. Combined with the higher oil recovery rates achieved, this means that SAGD is much more economic than pressure-driven steam process where the reservoir is reasonably thick.^[6]

History

The gravity drainage idea was originally conceived by Dr. Roger Butler, an engineer for Imperial Oil in the 1970s^[1][2] In 1975 Imperial Oil transferred Butler from Sarnia, Ontario to Calgary, Alberta to head their heavy oil research effort, Butler was able to pursued the concept. He tested the concept with Imperial Oil in 1980, in a pilot at Cold Lake which featured one of the first horizontal wells in the industry, with vertical injectors.

Alberta Oil Sands Technology and Research Authority (AOSTRA) 1974

In 1974, former Premier of Alberta created the Alberta Oil Sands Technology and Research Authority (AOSTRA) as an Alberta crown corporation to promote the development and use of new technology for oil sands and heavy crude oil production, and enhanced recovery of conventional crude oil. Its first facility was owned and operated by ten industrial participants and received ample government support (Deutsch and McLennan 2005)^[2] including from the Alberta Heritage Savings Trust Fund.^[7][8][9] One of the main targets of AOSTRA finding of suitable technologies for that part of the Athabasca Oil Sands that could not be recovered using conventional surface mining technologies.^[2]

AOSTRA Underground Test Facility 1984

In 1984, AOSTRA initiated the Underground Test Facility in the Athabasca Oil Sands, located between the MacKay Rivers and the Devon River west of the Syncrude plant as an in-situ SAGD bitumen recovery facility.^[2][10] It was there that they first test of twin (horizontal) SAGD wells took place, proving the feasibility of the concept, briefly achieving positive cash flow in 1992 at a production rate of about 2000 bbl/day from 3 well pairs. The idea was greatly furthered by the work of Roger Butler's Ph. D. student at the University of Calgary, Dr. Swapan Das.

Foster Creek

The Foster Creek plant in Alberta Canada, built in 1996, was the first commercial Steam-assisted gravity drainage (SAGD) project and by 2010 Foster Creek "became the largest commercial SAGD project in Alberta to reach royalty payout status. "^[10][11]

The original UTF SAGD wells were drilled horizontally from a tunnel in the limestone underburden, accessed with vertical mine shafts. The concept coincided with development of directional drilling techniques that allowed companies to drill horizontal wells accurately, cheaply and efficiently, to the point that it became hard to justify drilling a conventional vertical well any more. With the low cost of drilling horizontal well pairs, and the very high recovery rates of the SAGD process (up to 60% of the oil in place), SAGD is economically attractive to oil companies.

Current applications

This technology is now being exploited due to increased oil prices. While traditional drilling methods were prevalent up until the 1990s, high crude prices of the 21st Century are encouraging more unconventional methods (such as SAGD) to extract crude oil. The Canadian oil sands have many SAGD projects in progress, since this region is home of one of the largest deposits of bitumen in the world (Canada and Venezuela have the world's largest deposits).

The SAGD process allowed the Alberta Energy Resources Conservation Board (ERCB) to increase its proven oil reserves to 179 billion barrels, which raised Canada's oil reserves to the third highest in the world after Venezuela and Saudi Arabia and approximately quadrupled North American oil reserves. As of 2011, the oil sands reserves stand at around 169 billion barrels.

Disadvantages

Oil and water nexus

SAGD, a thermal recovery process, consumes large quantities of water(Glassman & 2011 4)^[5] and natural gas. "Petroleum from the Canadian oil sands extracted via surface mining techniques can consume 20 times more water than conventional oil drilling." However, by 2011 there was inadequate data on the amount of water used in the increasingly important steam-assisted gravity drainage technique (SAGD) method.(Glassman & 2011 4)

Use of natural gas for steam generation

As in all thermal recovery processes, cost of steam generation is a major part of the cost of oil production. Historically, natural gas has been used as a fuel for Canadian oil sands projects, due to the presence of large stranded gas reserves in the oil sands area. However, with the building of natural gas pipelines to outside markets in Canada and the United States, the price of gas has become an important consideration. The fact that natural gas production in Canada has peaked and is now declining is also a problem. Other sources of generating heat are under consideration, notably gasification of the heavy fractions of the produced bitumen to produce syngas, using the nearby (and massive) deposits of coal, or even building nuclear reactors to produce the heat.

Use of water for steam generation

A source of large amounts of fresh and brackish water and large water re-cycling facilities are required in order to create the steam for the SAGD process. Water is a popular topic for debate in regards to water use and management. As of 2008, American petroleum production (not limited to SAGD) generates over 5 billion gallons of produced water every day.^[12][13] The concern of using large amounts of water has little to do with proportion of water used, rather the quality of the water. Traditionally close to 70 million meters cubed of the water volume that was used in the SAGD process was fresh, surface, water. There has been a significant reduction in fresh water use as of 2010, when approximately 18 million cubic meters were used. Though to offset the drastic reduction in fresh water use, industry has began to significantly increase the volume of saline groundwater involved. This, as well as other, more general water saving techniques have allowed surface water usage by oil sands operations to decrease by more than threefold since production first began.^[14] Relying upon gravity drainage, SAGD also requires comparatively thick and homogeneous reservoirs, and so is not suitable for all heavy-oil production areas.

Alternative methods

By 2009 the two commercially applied primal thermal recovery processes, Steam Assisted Gravity Drainage (SAGD) and Cyclic Steam Stimulation (CSS), were used in oil sands production in the Clearwater and Lower Grand Rapids Formations in the Cold Lake Area in Alberta. (Jiang 2009)^[4]

Cyclic Steam Stimulation (CSS)

Canadian Natural Resources use "employs cyclic steam or "huff and puff" technology to develop bitumen resources. This technology requires one well bore and the production consists of the injection and production phases. First steam is "injected for several weeks, mobilizing cold bitumen". Then the flow "on the injection well is reversed producing oil through the same injection well bore. The injection and production phases together comprise one cycle. "Steam is re-injected to begin a new cycle when oil production rates fall below a critical threshold due to the cooling of the reservoir. "(CNRL 2013)^[15] Cyclic Steam Stimulation (CSS) also has a number of CSS Follow-up or Enhancement Processes, including Pressure Up and Blow Down (PUBD), Mixed Well Steam Drive and Drainage (MWSDD), Vapor Extraction (Vapex), Liquid Addition to Steam for Enhanced Recovery of Bitumen (LASER) and HPCSS Assisted SAGD and Hybrid Process. (Jiang 2009)^[4]

High pressure cyclic steam stimulation (HPCSS)

HPCSS Assisted SAGD and Hybrid Process: "Roughly 35 per cent of all in situ production in the Alberta oil sands uses a technique called High Pressure Cyclic Steam Stimulation (HPCSS), which cycles between two phases: first, steam is injected into an underground oil sands deposit to soften the bitumen; then, the resulting hot mixture of bitumen and steam (called a “bitumen emulsion”) is pumped up to the surface. The process is then repeated multiple times. "(Severson-Baker 2013)^[16] An Alberta Energy Regulator (AER) news release explained the difference between high pressure cyclic steam stimulation (HPCSS) and steam assisted gravity drainage (SAGD). "HPCSS has been used in oil recovery in Alberta for more than 30 years. The method involves injecting high-pressure steam into a reservoir over a prolonged period of time. As heat softens the bitumen and water dilutes and separates the bitumen from the sand, the pressure creates cracks and openings through which the bitumen can flow back into the steam-injector wells. HPCSS differs from steam assisted gravity drainage (SAGD) operations where steam is injected at lower pressures without fracturing the reservoir and uses gravity drainage as the primary recovery mechanism. "(2013 AER)^[17]

In the Clearwater Formation near Cold Lake, Alberta the High Pressure Cyclic Steam Stimulation (HPCSS) is used. (Jiang 2009)^[4] There are both horizontal and vertical wells. Injection is at fracture pressure. There is a 60 m to 180 m spacing for horizontal wells. Vertical wells are spaced at 2 to 8 Acre spacing for vertical wells. The development can be as low as 7 m net pay. It is used in areas generally with no to minimal bottom water or top gas. The CSOR is 3.3 to 4.5. The ultimate recovery is predicted at 15 to 35%.(Jiang 2009)^[4] SAGD thermal recovery method is also used in Clearwater and Lower Grand Rapids Formations with Horizontal Well Pairs (700 to 1000 m), Operating pressure 3 to 5 MPa, Burnt Lake SAGD was started with higher operating pressure close to dilation pressure, 75 m to 120 m spacing, Development to as low as 10 m net pay, In areas with or without bottom water, CSOR: 2.8 to 4.0 (at 100% quality), Predicted ultimate recovery: 45% to 55%.(Jiang 2009)^[4]

Canadian Natural Resources Limited’s (CNRL) Primrose and Wolf Lake in situ oil sands project near Cold Lake, Alberta in the Clearwater Formation, operated by CNRL subsidiary Horizon Oil Sands, use the high pressure cyclic steam stimulation (HPCSS). (2013 AER)

Vapor Extraction (Vapex)

Alternative enhanced oil recovery mechanisms include VAPEX (for Vapor Extraction), Electro-Thermal Dynamic Stripping Process (ET-DSP), and ISC (for In Situ Combustion). VAPEX, a "gravity-drainage process that uses vapourized solvents rather than steam to displace or produce heavy oil and reduce its viscosity, was also invented by Butler.^[18]

ET-DSP is a patented process that uses electricity to heat oil sands deposits to mobilize bitumen allowing production using simple vertical wells. ISC uses oxygen to generate heat that diminishes oil viscosity; alongside carbon dioxide generated by heavy crude oil displace oil toward production wells. One ISC approach is called THAI for Toe to Heel Air Injection.^[18]

See also

• Steam injection (oil industry)
• Enhanced oil recovery
• Alberta Oil Sands Technology and Research Authority
• Cenovus
• Heavy crude oil
• Oil shale
• Oil sands
• Mazut

Notes

References

External links

• SAGD process with a focus on Reverse Emulsions
• Description of SAGD and SAGD history
• Example Supplier of SAGD components
• Key Supplier of SAGD components
• Key Supplier of SAGD boilers