Rover K engine

From Wikipedia, the free encyclopedia
This article is about the Rover engine. For the Honda engine series of the same name, see Honda K engine.
A 1.8T DOHC K-Series engine in a MG 7

The K-Series engine is a series of engines built by Powertrain Ltd, a sister company of MG Rover. The engine was built in two forms: a straight-four cylinder, available with SOHC and DOHC, ranging from 1.1 L to 1.8 L; and the KV6 V6 variation.

Design history

The cylinder block of a United Kingdom Rover K-series 16-valve DOHC engine with damp liner cylinders

The K-Series was introduced in 1988 by Rover Group as a powerplant for the Rover 200 car. It was revolutionary in that it was the first volume production implementation of the low pressure sand casting technique. This works by injecting liquid aluminium into an upturned sand mould from below. In this way any oxide film always remains on the surface of the casting and is not stirred into the casting structure. This production technology overcame many of the inherent problems of casting aluminium components and consequently permitted lower casting wall thickness and higher strength to weight ratios. However, the process required the use of heat treated LM25 material which gave the engines a reputation for being fragile. An engine overheat would often result in the material becoming annealed and rendering the components scrap. The aluminium engine blocks were fitted with spun cast iron cylinder liners that were initially manufactured by GKN's Sheepbridge Stokes of Chesterfield, but replaced by spun cast iron liners made by Goetze after some seminal research conducted by Charles Bernstein at Longbridge, which proved influential even to Ducati for their race engines. Unfortunately a large number of aftermarket engines, the so-called "VHPD"s" were built with the old substandard GKNs by Minister, Lotus and PTP well after the Goetze liner's introduction to the production line in 2000.


The engine was introduced initially in 1.1 L single overhead cam and 1.4 L dual overhead cam versions. The engines were held together as a sandwich of components by long through-bolts which held the engine under compression, though this construction is not unknown in early lightweight fighter engines from the First World War. It had also been used in motorcycle engines and Triumph Car's "Sabrina" race engine. As Honda stopped providing Rover with engines after the end of their relationship, but well before the BMW takeover, an enlargement of the K Series design to 1.6 and 1.8 litres was carried out. This was done by using larger diameter cylinder liners and also increasing the stroke. The change required a block redesign with the removal of the cylinder block's top deck and a change from "wet" liners to "damp" liners.[1] The plastic throttle body fitted to the engine until 2001 was manufactured by the SU Carburettor company - they also included aluminium and larger sized bodies.

The two types of head that were bolted to the common four-cylinder block were designated K8 (8 valves) and K16 (16 valves). A later head design also incorporated a Rover-designed Variable Valve Control (VVC) unit (derived from an expired AP patent). This allowed more power to be developed without compromising low-speed torque and flexibility. The VVC system constantly alters the inlet cam period, resulting in a remarkably flexible drive - the torque curve of a VVC K-series engine is virtually flat throughout the rev range and power climbs steadily with no fall-off whatsoever until the rev limiter kicks in at 7,200 rpm.

By comparison, the V6 engines are more conventional engines that do not make use of the through bolts to hold the head to the block.

Engine management

K8 engine

Early K8 engines used a single SU KIF carburetter with a manual choke and a breaker-less distributor mounted on the end of the camshaft. MEMS Single point injection became standard with the launch of the Rover 100 in 1994.

K16

K16 models used MEMS With a 1.6 ECU on 1990 to 1994 or a 1.9 ECU On 1995 onwards electronic engine management in either Single Point or Multi Point forms, with a single coil on the back of the engine block and a distributor cap and rotor arm on the end of the inlet camshaft. MEMS 2J was used on the VVC engine, to control the Variable Valve Control and also the distributorless ignition system, which was necessary thanks to having camshaft drive belts at both ends of the engine. With the launch of the Rover 25 and Rover 45 in 1999, MEMS 3 was introduced, with twin coils and sequential injection.

KV6

Early KV6 as used in the Rover 800 used MEMS 2J, which controlled the three wasted spark coil packs and variable intake manifold geometry. The later KV6 used Siemens EMS 2000.

Model range

1100

All 1100 engines displace 1.1 L (1,120 cc/68 cu in). Four variations were created:

  • SOHC K8 8-valve, Carburettor, 60 hp (44 kW)
  • SOHC K8 8-valve, SPI, 60 hp (44 kW)
  • SOHC K8 8-valve, MPI, 60 hp (44 kW)
  • DOHC K16 16-valve, MPI, 75 hp (55 kW)

Cars that came with the 1100:

  • Rover Metro
  • Rover 100
  • Rover 200
  • Rover 25

1400

1.4-litre DOHC K-Series engine in a MG ZR

Engine Codes: 14K2F (8V), 14K4F (16V), 14K16 (16V)?

All 1400 engines displace 1.4 L (1,396 cc/85 cu in). Six variations were created:

  • SOHC K8 8-valve, Carburettor, 75 hp (55 kW)
  • SOHC K8 8-valve, SPI, 75 hp (55 kW)
  • SOHC K8 8-valve, MPI, 75 hp (55 kW)
  • DOHC K16 16-valve, SPI, 90 hp (66 kW)
  • DOHC K16 16-valve, MPI, 82 hp (61 kW)
  • DOHC K16 16-valve, MPI, 103 hp (76 kW)

The K16 82 hp variant is exactly the same as the 103 hp (77 kW) version, apart from a restrictive throttle body designed to lower the car's insurance group; the 90 hp (67 kW) Spi features single-point fuel injection rather than the multi-point of the later engine.

Cars that came with the 1400:

1600

Engine Code: 16K4F

All 1600 engines displace 1.6 L (1,588 cc/96 cu in). Two variations were created:

  • DOHC K16 16-valve, MPI, 109 hp (80 kW)
  • DOHC K16 16-valve, MPI, 111 hp (82 kW)

Cars that came with the 1600:

1800

Engine Codes: 18K4F, 18K4K (VVC variants)

All 1800 engines displace 1.8 L (1,795 cc/109 cu in). Six variations were created:

  • DOHC K16 16-valve, MPI, 117 to 120 hp (86 to 88 kW)
  • DOHC K16 16-valve, MPI, 136 hp (100 kW)
  • DOHC K16 16-valve, MPI, VVC, 145 hp (107 kW)
  • DOHC K16 16-valve, MPI, VVC, 160 hp (118 kW)
  • DOHC K16 16-valve, MPI, turbocharged, 150 to 160 hp (110 to 118 kW)
  • DOHC K16 VHPD - Very High Performance Derivative 16-valve, MPI, 177 hp (130 kW) or 192 hp (142 kW) (Lotus version) (Uses VVC unique cylinder head casting (similar to VVC casting), has big valves, but with fixed cam timing - No development input was requested from Rover)

Cars that came with the 1800:

References

  1. ↑ Adcock, Ian (1996). Project Phoenix: the birth of the MGF. Bloomsbury. p. 175. ISBN 0-7475-2695-8. 

Further reading

  • Engine Overhaul Manual. Rover K-Series. MG Rover Group. 
  • Hammill, Des (2008). The Rover K-series 16V Engine. 1989-2005. CP Press. ISBN 1-84155-688-2. 
This article is issued from Wikipedia. The text is available under the Creative Commons Attribution/Share Alike; additional terms may apply for the media files.