Melt flow index

From Wikipedia, the free encyclopedia

Melt flow index or MFI is a measure of the ease of flow of the melt of a thermoplastic polymer. It is defined as the mass of polymer, in grams, flowing in ten minutes through a capillary of a specific diameter and length by a pressure applied via prescribed alternative gravimetric weights for alternative prescribed temperatures.[1] The method is described in the similar standards ASTM D1238 [2] and ISO 1133.[3]

Melt flow rate is an indirect measure of molecular weight, with high melt flow rate corresponding to low molecular weight. At the same time, melt flow rate is a measure of the ability of the material's melt to flow under pressure. Melt flow rate is inversely proportional to viscosity of the melt at the conditions of the test, though it should be borne in mind that the viscosity for any such material depends on the applied force. Ratios between two melt flow rate values for one material at different gravimetric weights are often used as a measure for the broadness of the molecular weight distribution.

Melt flow rate is very commonly used for polyolefins, polyethylene being measured at 190°C and polypropylene at 230°C. The plastics converter should choose a material with a melt index so high that he can easily form the polymer in the molten state into the article intended, but on the other hand so low that the mechanical strength of the final article will be sufficient for its use.

Measurement

The procedure for determining MFI is as follows:

  1. A small amount of the polymer sample (around 4 to 5 grams) is taken in the specially designed MFI apparatus . The apparatus consists of a small die inserted into the apparatus, with the diameter of the die generally being around 2 mm.
  2. The material is packed properly inside the barrel to avoid formation of air pockets.
  3. A piston is introduced which acts as the medium that causes extrusion of the molten polymer.
  4. The sample is preheated for a specified amount of time: 5 min at 190°C for polyethylene and 6 min at 230°C for polypropylene.
  5. After the preheating a specified weight is introduced onto the piston. Examples of standard weights are 2.16 kg, 5 kg, etc.
  6. The weight exerts a force on the molten polymer and it immediately starts flowing through the die.
  7. A sample of the melt is taken after desired period of time and is weighed accurately.
  8. MFI is expressed as grams of polymer/10 minutes of total time of the test

Synonyms of Melt Flow Index are Melt Flow Rate and Melt Index. More commonly used are their abbreviations: MFI, MFR and MI.

Confusingly, MFR may also indicate "melt flow ratio", the ratio between two melt flow rates at different gravimetric weights. More accurately, this should be reported as FRR (flow rate ratio), or simply flow ratio. FRR is commonly used as an indication of the way in which rheological behavior is influenced by the molecular mass distribution of the material.

MFI is often used to determine how a polymer will process. However MFI takes no account of the shear, shear rate or shear history and as such is not a good measure of the processing window of a polymer. The MFI device is not an extruder in the conventional polymer processing sense in that there is no screw to compress, heat and shear the polymer. MFI additionally does not take account of long chain branching nor the differences between shear and elongational rheology. Therefore two polymers with the same MFI will not behave the same under any given processing conditions.[4]

References

  1. ↑ A. V. Shenoy, D. R. Saini: Melt Flow Index: More Than Just a Quality Control Parameter. Part I., Advances in Polymer Technology, vol 6, No. 1, pages 1 – 58.
  2. ↑ ASTM D1238-04
  3. ↑ ISO 1133:1997.
  4. ↑ P. Prentice, Rheology and its role in plastics processing: No.12, p25, Section 3.1.3, 1995

External links

This article is issued from Wikipedia. The text is available under the Creative Commons Attribution/Share Alike; additional terms may apply for the media files.